Home › General › MAINTENANCE › 1GR-FE DRIVE BELT
RM38G0E _V1 General _100461 MAINTENANCE _0470534 1GR-FE DRIVE BELT A

MAINTENANCE  1GR-FE DRIVE BELT  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A487691N02
2.25,0.177 3.25,0.375 1,0.198 1.469,1.698 1.99,1.698 false 2.448,0.729 2.969,0.729 false 3.635,0.5 3.635,0.271 3.635,0.271 3.26,0.271 true 2.292,0.604 2.573,0.958 0.281,0.354 18 false 2 1.271,1.583 1.552,1.938 0.281,0.354 18 false 1 3.74,0.448 4.021,0.802 0.281,0.354 10 false x 2 2.313,0.208 3.333,0.448 1.021,0.24 8 false 5.0 (51, 44 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FAN AND GENERATOR V BELT 16361A (Click here) - -
2 RADIATOR RESERVE TANK ASSEMBLY 16470 - - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

PROCEDURE

Hide 16361A 1.INSTALL FAN AND GENERATOR V BELT

a.
A487694C01
2.313,1.146 2.521,1.146 true 4.51,3.292 4.99,3.292 true 0.396,0.156 0.677,0.51 0.281,0.354 18 false i 3.813,0.156 4.094,0.51 0.281,0.354 18 false ii 0.385,2.219 0.667,2.573 0.281,0.354 18 false iii 1.167,0.927 1.375,1.146 0.208,0.219 10 false *1 1.76,0.917 1.969,1.135 0.208,0.219 10 false *2 1.469,1.115 1.677,1.333 0.208,0.219 10 false *3 2.24,0.823 2.448,1.042 0.208,0.219 10 false *3 2.635,0.875 2.844,1.094 0.208,0.219 10 false *4 2.521,1.323 2.729,1.542 0.208,0.219 10 false *5 2.167,1.375 2.375,1.594 0.208,0.219 10 false *6 1.76,1.313 1.969,1.531 0.208,0.219 10 false *7 2.563,1.052 2.771,1.271 0.208,0.219 10 false *8 1.094,2.292 1.302,2.51 0.208,0.219 10 false *a 2.698,2.292 2.906,2.51 0.208,0.219 10 false *b 4.354,3.198 4.563,3.417 0.208,0.219 10 false *c
*1 Vane Pump Assembly *2 Water Pump Assembly
*3 No. 2 Idler Pulley Sub-assembly *4 Generator Assembly
*5 Compressor with Magnet Clutch *6 No. 1 Idler Pulley Sub-assembly
*7 Crankshaft Pulley *8 V-ribbed Belt Tensioner Assembly
*a Correct *b Incorrect
*c 5 mm Hexagon Wrench - -
V113147

Turn in this Direction
V113148

Remove in this Direction


i.

Set the fan and generator V belt onto each part.


ii.

While turning the belt tensioner counterclockwise, remove the 5 mm hexagon wrench.

NOTICE:

Make sure that the fan and generator V belt is properly installed to each pulley.



iii.

Check that the belt fits properly in the ribbed grooves.



Hide 16470 2.INSTALL RADIATOR RESERVE TANK ASSEMBLY

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)