Home › General › MAINTENANCE › 1GR-FE OIL AND OIL FILTER
RM38G0E _V1 General _100461 MAINTENANCE _0470535 1GR-FE OIL AND OIL FILTER A

MAINTENANCE  1GR-FE OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

·

Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.

·

In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.



PROCEDURE

Hide 51410 1.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

a.
A485296C01
0,0 0,0 false
V100135

Bolt A
V100136

Bolt B


Remove the 5 bolts (A) and 4 bolts (B).


b.
A485297C01
0,0 0,0 false
V113147

Remove in this Direction


Move the side of No. 1 engine under cover assembly facing the front of the vehicle toward the LH side and detach the temporary holding guide.


c.
A482305C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the No. 1 engine under cover assembly facing the front of the vehicle while pulling the engine side cover sub-assembly RH and engine side cover sub-assembly LH, and then remove the No. 1 engine under cover assembly while detaching the 2 temporary holding guides facing the rear of the vehicle as shown in the illustration.


Hide 51455C 2.REMOVE NO. 2 ENGINE UNDER COVER SEAL

a.
A487288

Remove the 3 screws and No. 2 engine under cover seal.


Hide 3.DRAIN ENGINE OIL

a.

Remove the oil filler cap sub-assembly.


b.

Remove the oil pan drain plug and gasket, and drain the engine oil into a container.


c.

Install a new gasket and the oil pan drain plug.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 4.REMOVE OIL FILTER ELEMENT

a.
A484143C01
1.125,0.625 1.396,0.385 1.396,0.385 1.479,0.385 false 2.302,1.271 2.615,0.948 2.615,0.948 2.74,0.948 false 2.771,0.865 3.073,1.083 0.302,0.219 10 false *b 1.521,0.313 1.854,0.49 0.333,0.177 10 false *a
*a Pipe
*b Hose


Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.


b.
A484144

Remove the oil filter drain plug.


c.
A484145C01
0.479,2.958 1,2.958 true 0.417,2.073 0.531,1.948 0.531,1.948 0.688,1.948 true 0.344,2.365 0.604,2.365 0.604,2.365 0.979,2.51 true 0.458,2.594 0.865,2.594 0.865,2.594 1.24,2.74 true 0.688,3.177 1.208,3.177 true 0.719,1.865 0.896,2.031 0.177,0.167 10 false *1 0.177,2.292 0.344,2.448 0.167,0.156 10 true *2 0.313,2.521 0.521,2.688 0.208,0.167 10 false *3 0.344,2.885 0.583,3.083 0.24,0.198 10 false *4 0.531,3.104 0.802,3.302 0.271,0.198 10 false *5
*1 Cap
*2 Valve
*3 Pipe
*4 O-ring
*5 Hose


Install the pipe to the oil filter cap.

NOTICE:

If the O-ring is removed with the drain plug, install the O-ring together with the pipe.


HINT:

Use a container to catch the draining oil.



d.
A484146

Check that oil is drained from the oil filter. Then, disconnect the pipe and remove the O-ring as shown in the illustration.


e.
A484147C01
2.01,1.365 2.677,1.365 true 2.083,1.01 2.75,1.01 true 2.802,0.917 3.052,1.146 0.25,0.229 10 false *1 2.729,1.281 3.104,1.51 0.375,0.229 10 false SST
*1 Oil Filter Bracket Clip


Using SST, remove the oil filter cap.

SST
09228-06502  

NOTICE:

Do not remove the oil filter bracket clip.



f.
A484148C01
0.521,1.198 1.083,1.198 true 0.354,1.125 0.594,1.344 0.24,0.219 10 false *1
*1 O-ring


Remove the oil filter element and O-ring from the oil filter cap.

NOTICE:

Be sure to remove the O-ring (for the cap) by hand, without using any tools, to prevent damage to the groove for the O-ring in the cap.



Hide 5.INSTALL OIL FILTER ELEMENT

a.

Clean the inside of the oil filter cap, the threads and O-ring groove.


b.
A484149C01
1.406,1.083 1.552,0.844 1.552,0.844 1.708,0.844 true 3.083,1.167 3.135,0.917 3.135,0.917 3.219,0.917 true 1.74,0.76 1.938,0.948 0.198,0.188 10 false *1 0.813,1.813 1.125,2.073 0.313,0.26 10 false *a 2.5,1.813 2.781,2 0.281,0.188 10 false *b 3.26,0.833 3.427,1.063 0.167,0.229 10 false *1
*1 O-ring
*a Correct
*b Incorrect


Apply a light coat of engine oil to a new O-ring for the cap, and then install the O-ring to the groove of the oil filter cap.

NOTICE:
·

Be sure to install the O-ring in the proper location, otherwise oil may leak.

·

Do not twist the O-ring.




c.

Set a new oil filter element in the oil filter cap.


d.

Remove any dirt or foreign matter from the installation surface of the engine.


e.

Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.

NOTICE:

Do not pinch the O-ring for the cap.



f.
A484150C01
1.781,2.604 1.625,2.604 1.625,2.604 1.552,2.396 true 0.76,3.146 0.969,3.146 0.969,3.146 1.167,2.469 true 0.438,2.896 0.604,2.896 0.604,2.896 0.719,2.542 true 2.844,2.344 3.125,2.344 3.125,2.344 2.885,1.458 true 1.813,2.51 2.115,2.719 0.302,0.208 10 false *1 0.604,3.063 0.865,3.292 0.26,0.229 10 false *2 0.281,2.823 0.531,3.021 0.25,0.198 10 false *3 1.344,2.938 1.615,3.156 0.271,0.219 10 false *a 2.552,2.271 2.906,2.521 0.354,0.25 10 false SST
*1 Oil Filter Cap
*2 O-ring
*3 Oil Filter Bracket
*a No Gap


Using SST, tighten the oil filter cap.

SST
09228-06502  

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:

After tightening the oil filter cap, make sure that there is no gap and that the O-ring is not protruding.



g.
A484151C01
0.396,2.969 0.979,2.969 true 0.25,2.896 0.552,3.073 0.302,0.177 10 false *1
*1 O-ring


Apply a small amount of engine oil to a new drain plug O-ring and install the O-ring to the oil filter cap.

NOTICE:

Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.



h.

Install the oil filter drain plug.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:

Make sure that the O-ring does not get caught between the parts.



Hide 6.ADD ENGINE OIL

a.

Add clean engine oil.

NOTICE:
A308107

Do not allow engine oil to adhere to the moving parts of the belt tensioner, as this may cause malfunctions.

If engine oil is on the location indicated by the arrow, replace the belt tensioner.


Standard Engine Oil:
Oil Grade Oil Viscosity (SAE)
API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving", SN PLUS "resource-conserving" or SP "resource-conserving"; or ILSAC GF-6A multigrade engine oil 0W-20
5W-20
5W-30
10W-30


Standard Oil Capacity:
Item Specified Condition
Drain and refill without oil filter change 5.6 liters (5.9 US qts, 4.9 Imp. qts)
Drain and refill with oil filter change 6.1 liters (6.4 US qts, 5.4 Imp. qts)
Dry fill 7.1 liters (7.5 US qts, 6.2 Imp. qts)



Hide 8.INSPECT FOR OIL LEAK

a.

Start the engine. Make sure that there are no oil leaks from the area that was worked on.


Hide 51455C 9.INSTALL NO. 2 ENGINE UNDER COVER SEAL

a.

Install the No. 2 engine under cover seal with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 51410 10.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

a.
A482306C01
0,0 0,0 false
V113147

Install in this Direction


After attaching the 2 temporary holding guides of the No. 1 engine under cover assembly to the vehicle frame, set the No. 1 engine under cover assembly to the vehicle side while pulling the engine side cover sub-assembly RH and engine side cover sub-assembly LH as shown in the illustration.


b.
A485308C01
0,0 0,0 false
V113147

Install in this Direction


Move the side of No. 1 engine under cover assembly facing the front of the vehicle and attach the 2 temporary holding guides to the vehicle frame.


c.
A485296C01
0,0 0,0 false
V100135

Bolt A
V100136

Bolt B


Install the 5 bolts (A) and 4 bolts (B).

Torque:
for bolt (A) : 29 N*m (296 kgf*cm, 21 ft.*lbf)