Home › Engine / Hybrid System › 1GR-FE (LUBRICATION) › LUBRICATION SYSTEM
RM38G0E _51 Engine / Hybrid System _101208 1GR-FE LUBRICATION _0469491 LUBRICATION SYSTEM G

1GR-FE LUBRICATION  LUBRICATION SYSTEM  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:
·
A343690

To prevent injury due to contact with an operating fan and generator V-belt or cooling fan, keep your hands and clothing away from the fan and generator V-belt and cooling fans when working in the engine compartment with the engine running.

·
A343694

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
A343699

To prevent burns, do not remove the engine oil pressure switch assembly while the engine is hot.



PROCEDURE

Hide 1.CHECK ENGINE OIL QUALITY

a.

Check the oil for deterioration, water contamination, discoloration or thinning.

If the quality is visibly poor, replace the oil and oil filter element.

Click hereGeneral>MAINTENANCE>1GR-FE OIL AND OIL FILTER>REPLACEMENT


Hide 2.INSPECT ENGINE OIL LEVEL

a.

Warm up the engine, and then stop the engine and wait for 5 minutes.


b.

Check that the engine oil level is between the low and full level marks on the engine oil dipstick.

If the oil level is low, check for leakage and add oil up to the full level mark.

NOTICE:

Do not fill engine oil above the full level mark.


HINT:

A certain amount of engine oil will be consumed while driving. In the following situations, oil consumption may increase, and engine oil may need to be refilled in between oil maintenance intervals.

·

When the engine is new, for example directly after purchasing the vehicle or after replacing the engine.

·

If low quality oil or oil of an inappropriate viscosity is used.

·

When driving at a high engine speed or with a heavy load, when towing, or when driving while accelerating or decelerating frequently.

·

When idling for a long time, or when driving frequently through heavy traffic.


When judging the amount of oil consumption, keep in mind that the oil may have become diluted, making it difficult to judge the true level accurately.



Hide 3.INSPECT OIL PRESSURE

CAUTION:
·

To prevent injury due to contact with an operating fan and generator V-belt or cooling fan, keep your hands and clothing away from the fan and generator V-belt and cooling fans when working in the engine compartment with the engine running.

·

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·

To prevent burns, do not remove the engine oil pressure switch assembly while the engine is hot.



a.

Remove the engine oil pressure switch assembly.

Click hereEngine / Hybrid System>1GR-FE (LUBRICATION)>OIL PRESSURE SWITCH>REMOVAL


b.
A484140C01
2.771,1.229 3.094,1.229 true 3.135,1.135 3.365,1.396 0.229,0.26 10 false *a
*a Oil Pressure Gauge


Install an oil pressure gauge.


c.

Warm up the engine.


d.

Measure the engine oil pressure.

Standard Oil Pressure:
Condition Specified Condition
Idle 30 kPa (0.3 kgf/cm2, 4.4 psi) or higher
3000 rpm 200 kPa (2.0 kgf/cm2, 29 psi) or higher


If the result is not as specified, check the quality of the engine oil and check the oil paths for clogging. Repair or replace if necessary. If the engine oil pressure is still not as specified, check the oil pump.

Click hereEngine / Hybrid System>1GR-FE (LUBRICATION)>OIL PUMP>INSPECTION


e.

Remove the oil pressure gauge.


f.

Install the engine oil pressure switch assembly.

Click hereEngine / Hybrid System>1GR-FE (LUBRICATION)>OIL PRESSURE SWITCH>INSTALLATION