Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock)
RM38G0E _52 Drivetrain _100455 AXLE AND DIFFERENTIAL _0473040 REAR DIFFERENTIAL CARRIER ASSEMBLY(w/ Differential Lock) A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY(w/ Differential Lock)  DISASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (DISASSEMBLY)
C458048N01
3.688,3.021 4.188,3.021 true 1.135,1.292 1.302,1.292 true 2.063,1.323 2.146,1.49 2.146,1.49 2.313,1.49 true 2.406,0.844 2.406,0.448 2.406,0.448 2.531,0.448 true 2.875,0.99 2.979,1.281 2.979,1.281 3.115,1.281 true 3.802,0.563 3.917,0.208 3.917,0.208 4.083,0.208 true 1.656,2.917 1.583,3.167 1.583,3.167 1.417,3.167 true 1.552,3.625 2.292,3.552 2.292,3.552 2.458,3.552 true 3.323,0.906 3.365,1.083 3.365,1.083 3.5,1.083 true 4.375,0.625 4.417,0.844 4.417,0.844 4.5,0.844 true 2.167,5.333 2.25,5.5 2.25,5.5 2.417,5.5 true 6.156,5.271 6.281,5.271 6.281,5.271 6.406,4.958 true 6.615,0.198 6.875,0.198 true 5.292,3.583 5.292,3.26 5.292,3.26 5.458,3.26 true 4.406,4.521 4.51,4.875 4.51,4.875 4.677,4.875 true 3.563,4.365 3.76,3.896 3.76,3.896 3.927,3.896 true 3.24,4.802 3.354,5.125 3.354,5.125 3.521,5.125 true 4.156,3.417 4.385,3.417 true 6.094,4.417 6.177,4.208 6.177,4.208 6.344,4.208 true 2.75,4.896 2.865,5.219 2.865,5.219 3.031,5.219 true 6.063,0.063 6.729,0.438 0.667,0.375 18 false 2 - 5 4.51,0.073 4.927,0.417 0.417,0.344 18 false 18 2.5,5.354 2.885,5.688 0.385,0.333 18 false 1 4.458,2.896 4.875,3.24 0.417,0.344 18 false 11 5,4.74 5.417,5.083 0.417,0.344 18 false 14 4.656,0.708 5.021,1.01 0.365,0.302 18 false 15 3.552,0.938 3.969,1.281 0.417,0.344 18 false 17 3.188,1.156 3.542,1.5 0.354,0.344 18 false 9 3.052,0.281 3.406,0.625 0.354,0.344 18 false 8 2.781,1.333 3.198,1.677 0.417,0.344 18 false 7 0.938,1.167 1.26,1.521 0.323,0.354 18 false 6 5.844,3.115 6.26,3.458 0.417,0.344 18 false 12 5.854,5.146 6.271,5.49 0.417,0.344 18 false 11 4.344,3.74 4.76,4.083 0.417,0.344 18 false 16 3.813,4.99 4.229,5.333 0.417,0.344 18 false 19 1.083,3.021 1.458,3.365 0.375,0.344 18 false 10 3,3.427 3.375,3.771 0.375,0.344 18 false 13 4.167,2.688 4.625,2.885 0.458,0.198 10 false x 2 6.875,4.51 7.146,4.76 0.271,0.25 10 false x 2 4.427,3.323 4.688,3.542 0.26,0.219 10 false *2 6.417,4.104 6.677,4.323 0.26,0.219 10 false *2 3.094,5.135 3.406,5.333 0.313,0.198 10 false *1 0.99,3.073 1.25,3.292 0.26,0.219 10 false ● 0.802,1.208 1.063,1.427 0.26,0.219 10 false ● 4.563,0.74 4.729,0.948 0.167,0.208 10 false ● 4.406,0.115 4.573,0.323 0.167,0.208 10 false ● 2.833,3.469 3.042,3.698 0.208,0.229 10 false ● 2.875,0.333 3.135,0.552 0.26,0.219 10 false ● 4.219,3.792 4.427,4.021 0.208,0.229 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 SECURE REAR DIFFERENTIAL CARRIER ASSEMBLY 41110 - - -
2 INSPECT REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY 41204 - - -
3 INSPECT RUNOUT OF DIFFERENTIAL RING GEAR - - - -
4 INSPECT DIFFERENTIAL RING GEAR BACKLASH - (Click here) - -
5 INSPECT TOTAL PRELOAD - - - -
6 REAR DRIVE PINION NUT 41204B (Click here) - -
7 REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR 41204 (Click here) - -
8 REAR DIFFERENTIAL CARRIER OIL SEAL 41201C - - -
9 REAR DIFFERENTIAL DRIVE PINION OIL SLINGER 41214 - - -
10 WIRING HARNESS CONNECTOR - - - -
11 DIFFERENTIAL BEARING CAP - (Click here) - -
12 ELECTRONIC DIFFERENTIAL LOCK CASE SUB-ASSEMBLY 41303E (Click here) - -
13 DIFFERENTIAL LOCK INDICATOR SWITCH 84222Q - - -
14 DIFFERENTIAL DRIVE PINION - (Click here) - -
15 REAR DIFFERENTIAL DRIVE PINION BEARING SPACER 41231 - - -
16 REAR DRIVE PINION REAR BEARING (INNER) 41201A (Click here) - -
17 REAR DRIVE PINION FRONT BEARING (INNER) 41201B - - -
18 REAR DRIVE PINION FRONT BEARING (OUTER) 41201B (Click here) - -
19 REAR DRIVE PINION REAR BEARING (OUTER) 41201A (Click here) - -

*1 ADJUST SHIM *2 PLATE WASHER
● Non-reusable part - -

C458050N01
6.083,4.531 6.583,4.531 6.583,4.531 6.583,3.615 true 6.583,0.208 6.865,0.208 true 6.24,4.531 6.24,3.656 true 5.75,3.417 5.833,2.938 5.833,2.938 6.083,2.938 true 4.052,4.573 4.208,4.865 4.208,4.865 4.458,4.865 true 5.438,3.417 5.583,2.5 5.583,2.5 5.75,2.5 true 5.052,3.948 5.167,4.25 5.167,4.25 5.333,4.25 true 4.583,4.25 4.667,4.5 4.667,4.5 4.833,4.5 true 2.802,3.938 3.031,3.208 3.031,3.208 3.281,3.208 true 1.5,5.5 0.552,5.5 0.552,5.5 0.552,5.219 true 1.083,5.5 1.083,5.052 true 2.354,4.719 2.469,5.021 2.469,5.021 2.635,5.021 true 1.688,4.271 1.833,3.896 1.833,3.896 2,3.896 true 4.26,1.938 4.542,1.938 true 3.615,2.385 3.896,2.385 true 3.594,0.875 3.875,0.875 true 2.438,1.219 2.719,1.219 true 4.104,1.333 4.25,1 4.25,1 4.417,1 true 2.583,2.25 2.771,2.25 2.771,2.25 2.854,1.917 true 2.167,0.75 2.333,0.75 2.333,0.75 2.417,0.917 true 3.573,0.542 3.854,0.542 true 3.573,2.667 3.854,2.667 true 4.604,2.167 4.885,2.167 true 1.979,1.917 2.26,1.917 true 4.542,1.448 4.604,1.604 4.604,1.604 4.688,1.604 true 5.167,1.26 5.313,1.542 5.313,1.542 5.396,1.542 true 4.844,1.177 4.979,0.688 4.979,0.688 5.063,0.688 true 3.667,1.698 3.74,2.146 3.74,2.146 3.823,2.146 true 2.927,2.51 3.094,2.51 3.094,2.51 3.313,2.135 true 3.292,1.938 3.5,1.938 true 3.552,1.24 3.76,1.24 true 2.854,0.583 3.021,0.583 3.021,0.583 3.354,1.26 true 4.938,3.188 5,2.833 5,2.833 5.167,2.833 true 6.396,2.813 6.875,3.229 0.479,0.417 18 false 23 5.635,4.458 5.792,4.656 0.156,0.198 10 false ● 5.771,4.417 6.25,4.833 0.479,0.417 18 false 22 4.771,4.75 5.25,5.167 0.479,0.417 18 false 20 5.823,2.354 6.302,2.771 0.479,0.417 18 false 24 5.396,4.104 5.875,4.521 0.479,0.417 18 false 25 4.917,4.354 5.396,4.771 0.479,0.417 18 false 27 3.635,3.063 4.167,3.406 0.531,0.344 18 false 26 5.323,0.073 6.698,0.427 1.375,0.354 18 false 21, 28 , 29 1.99,5.365 2.469,5.698 0.479,0.333 18 false 22 1.844,5.385 2,5.583 0.156,0.198 10 false ● 2.688,4.927 3,5.125 0.313,0.198 10 false *1 2.063,3.813 2.375,4.01 0.313,0.198 10 false *2 4.604,1.844 4.917,2.042 0.313,0.198 10 false *3 3.958,2.302 4.271,2.5 0.313,0.198 10 false *3 3.938,0.792 4.25,0.99 0.313,0.198 10 false *3 2.25,1.135 2.51,1.333 0.26,0.198 10 false *3 4.479,0.896 4.792,1.094 0.313,0.198 10 false *4 2.406,2.156 2.656,2.354 0.25,0.198 10 false *5 4.938,2.073 5.25,2.271 0.313,0.198 10 false *6 1.979,0.656 2.292,0.854 0.313,0.198 10 false *6 3.906,0.448 4.219,0.646 0.313,0.198 10 false *6 3.927,2.573 4.135,2.792 0.208,0.219 10 false *6 1.792,1.823 2.042,2.021 0.25,0.198 10 false *7 5.458,1.448 5.771,1.646 0.313,0.198 10 false *8 5.125,0.615 5.438,0.813 0.313,0.198 10 false *9 4.74,1.521 5.052,1.719 0.313,0.198 10 false *10 3.854,2.063 4.167,2.323 0.313,0.26 10 false *11 3.042,1.865 3.354,2.125 0.313,0.26 10 false *12 2.667,2.427 3,2.677 0.333,0.25 10 false *13 3.833,1.146 4.146,1.406 0.313,0.26 10 false *12 2.615,0.49 2.948,0.74 0.333,0.25 10 false *13 1.427,5.208 1.771,5.438 0.344,0.229 10 false x 12 3.531,4.76 3.875,4.99 0.344,0.229 10 false x 3 5.021,3.115 5.365,3.344 0.344,0.229 10 false x 3 5.229,2.729 5.385,2.927 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

20 DIFFERENTIAL RING GEAR - (Click here) - -
21 INSPECT DIFFERENTIAL CASE ASSEMBLY RUNOUT - (Click here) - -
22 REAR DIFFERENTIAL CASE BEARING(INNER) 41301A (Click here) - -
23 DIFFERENTIAL SOLENOID WASHER - (Click here) - -
24 DIFFERENTIAL LOCK COIL 41451H - - -
25 DIFFERENTIAL LOCK PLUNGER - - - -
26 REAR DIFFERENTIAL CASE SUB-ASSEMBLY 41303E (Click here) - -
27 DIFFERENTIAL LOCK POSITION PLATE 41474A - - -
28 DIFFERENTIAL GEAR KIT - - - -
29 INSPECT DIFFERENTIAL CASE - - - -

*1 DIFFERENTIAL LOCK CAM RING *2 DIFFERENTIAL CASE LH
*3 DIFFERENTIAL PINION *4 DIFFERENTIAL SIDE GEAR (DOG CLUTCH)
*5 DIFFERENTIAL SIDE GEAR *6 REAR DIFFERENTIAL PINION THRUST WASHER
*7 REAR NO. 1 DIFFERENTIAL SIDE GEAR THRUST WASHER *8 REAR NO. 2 DIFFERENTIAL SIDE GEAR THRUST WASHER
*9 REAR NO. 3 DIFFERENTIAL SIDE GEAR THRUST WASHER *10 DIFFERENTIAL LOCK SPRING
*11 REAR DIFFERENTIAL PINION SHAFT *12 REAR NO. 2 DIFFERENTIAL PINION SHAFT
*13 REAR DIFFERENTIAL PINION SHAFT PIN - -
● Non-reusable part - -

PROCEDURE

Hide 41110 1.SECURE REAR DIFFERENTIAL CARRIER ASSEMBLY

a.
C458054


Hide 41204 2.INSPECT REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
C458055C01
4.344,1.604 4.51,1.76 0.167,0.156 10 true *a
*a 36 mm (1.42 in.) - -


i.

Using a dial indicator, measure the runout of the rear drive pinion companion flange sub-assembly vertically and laterally.

Maximum Runout:
Runout Maximum
Vertical runout 0.10 mm (0.00394 in.)
Lateral runout 0.10 mm (0.00394 in.)


If the runout is more than the maximum, replace the rear drive pinion companion flange sub-assembly.



Hide 3.INSPECT RUNOUT OF DIFFERENTIAL RING GEAR

a.
C458056C01
4.542,1.406 4.854,1.563 0.313,0.156 10 false *a
*a 108 mm (4.25 in.) - -


i.

Using a dial indicator, measure the runout of the differential ring gear.

Maximum runout:

0.05 mm (0.00197 in.)


If the runout is more than the maximum, replace the differential ring gear with a new one.



Hide 4.INSPECT DIFFERENTIAL RING GEAR BACKLASH

a.
C458057N01
0.448,0.063 0.729,0.417 0.281,0.354 18 false i

i.

Using a dial indicator, measure the backlash of the differential ring gear.

Standard backlash:

0.10 to 0.20 mm (0.00394 to 0.00787 in.)


If the backlash is not within the specification, adjust the side bearing preload or perform repairs as necessary.

HINT:

Perform the measurement at 3 or more positions around the circumference of the differential ring gear.




Hide 5.INSPECT TOTAL PRELOAD

a.
C458107N01
0.125,0.083 0.406,0.438 0.281,0.354 18 false i

i.

Using a torque wrench, measure the preload with the teeth of the differential drive pinion and differential ring gear in contact.

If the result is not as specified, adjust the preload.

Standard Total Preload:
Reduction Ratio Specified Condition
3.307 1.24 to 2.60 N*m (13 to 26 kgf*cm, 11 to 23 in.*lbf)
4.300 1.18 to 2.48 N*m (13 to 25 kgf*cm, 11 to 21 in.*lbf)




Hide 41204B 6.REMOVE REAR DRIVE PINION NUT

a.
C458059C01
1.448,0.385 1.531,0.135 1.531,0.135 1.698,0.135 true 5.917,1.167 6.5,1.167 true 6.583,1.073 7.042,1.271 0.458,0.198 10 false SST 1.75,0.052 2.208,0.25 0.458,0.198 10 false SST 4.104,0.073 4.438,0.406 0.333,0.333 18 false ii 0.427,0.073 0.667,0.417 0.24,0.344 18 false i 4.417,1.24 4.729,1.396 0.313,0.156 10 false *a 5.969,1.542 6.281,1.698 0.313,0.156 10 false *b
*a Turn *b Hold


i.

Using a chisel and hammer, stake the rear drive pinion nut.

SST
09930-00010  (09931-00010, 09931-00020)


ii.

Using SST to hold the companion flange in place, remove the rear drive pinion nut.

SST
09330-00021  (09330-00030)



Hide 41204 7.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

a.
C458060C01
3.667,0.583 3.833,0.583 3.833,0.583 3.958,0.979 true 5.531,0.458 5.844,0.615 0.313,0.156 10 false *a 2.844,0.917 3.063,1.104 0.219,0.188 10 false *b 3.375,0.51 3.677,0.76 0.302,0.25 10 false SST 0.438,0.073 0.823,0.406 0.385,0.333 18 false i
*a Turn *b Hold


i.

Using SST, remove the rear drive pinion companion flange sub-assembly with dust deflector.

SST
09950-40011  (09951-04010, 09953-04020, 09954-04010, 09955-04061)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.




Hide 41201C 8.REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

a.
C458061C01
3.083,2.083 3.25,2.083 3.25,2.083 3.313,1.792 false 5,0.833 4.833,0.833 4.833,0.833 4.76,0.719 true 5.125,1.385 4.969,1.385 4.969,1.385 4.646,0.688 true 2.771,2 3.229,2.198 0.458,0.198 10 false SST 5.042,0.76 5.229,0.938 0.188,0.177 10 false *1 5.188,1.313 5.417,1.531 0.229,0.219 10 false *2 0.385,0.063 0.708,0.375 0.323,0.313 18 false i
*1 Rear Differential Carrier Oil Seal *2 Rear Differential Drive Pinion Oil Slinger


i.

Using SST, remove the rear differential carrier oil seal.

SST
09308-10010  



Hide 41214 9.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

a.
C458062


Hide 10.REMOVE WIRING HARNESS CONNECTOR

Z101186

HINT:

when the wiring is disconnect from the wiring harness connector, the claw on the connector side will break.



a.
C458063


Hide 11.REMOVE DIFFERENTIAL BEARING CAP

a.
C458064C01
2.417,1.167 2.417,0.833 2.417,0.833 3.031,0.833 true 2.167,1.167 3.469,1.167 true 2,1.063 2.25,1.313 0.25,0.25 10 false *a 1,2.083 1.25,2.333 0.25,0.25 10 false *b 4.583,2.083 4.813,2.333 0.229,0.25 10 false *c 0.396,2 0.75,2.302 0.354,0.302 18 false iii 1.583,0.083 2.031,0.448 0.448,0.365 18 false i, ii
*a Matchmark *b LH Side (Ring Gear Side)
*c RH Side (Differential Lock Coil Side) - -


i.

Place matchmarks on the differential bearing cap and differential carrier.


ii.

Remove the 4 bolts and 2 differential bearing caps.


iii.

Remove the 2 plate washers.

HINT:
·

Put identification marks on the plate washers to show the location for installation (LH side (ring gear side) or RH side (differential lock coil side)), or keep them separate so that they can be distinguished.

·

Measure the thickness of each plate washers and note it.





Hide 41303E 12.REMOVE ELECTRONIC DIFFERENTIAL LOCK CASE SUB-ASSEMBLY

a.
C458065N01
0.458,0.052 0.74,0.406 0.281,0.354 18 false i

i.

Remove the electronic differential lock case sub-assembly from the differential carrier.

NOTICE:
C463216C01
2.583,1.094 2.583,0.677 2.583,0.677 2.75,0.677 false 1.281,1.823 1.5,2 1.5,2 1.635,2 true 2.802,0.594 3.115,0.792 0.313,0.198 10 true *1 1.677,1.896 1.99,2.094 0.313,0.198 10 true *2
*1 Differential lock indicator switch
*2 Electronic differential lock case sub-assembly


After removing electronic differential lock case sub-assembly, remove differential lock indicator switch. Otherwise electronic differential lock case sub-assembly and differential lock indicator switch will be damaged.


HINT:

Tag the 2 rear differential case bearings (outer) so that they can be reinstalled in the correct locations.




Hide 84222Q 13.REMOVE DIFFERENTIAL LOCK INDICATOR SWITCH

Z101186

NOTICE:

After removing electronic differential lock case sub-assembly, remove differential lock indicator switch. Otherwise electronic differential lock case sub-assembly and differential lock indicator switch will be damaged.



a.
C458066


Hide 14.REMOVE DIFFERENTIAL DRIVE PINION

a.
C458067N01
0.406,0.063 0.615,0.333 0.208,0.271 18 false i

i.

Using a press, remove the differential drive pinion with rear differential drive pinion bearing spacer from the differential carrier.

NOTICE:

Do not drop the differential drive pinion.




Hide 41231 15.REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

a.
C458068


Hide 41201A 16.REMOVE REAR DRIVE PINION REAR BEARING (INNER)

a.
C458069N01
4.813,1.719 5.083,1.333 5.083,1.333 5.25,1.333 true 5.323,1.25 5.75,1.5 0.427,0.25 10 false SST 0.448,0.063 0.729,0.417 0.281,0.354 18 false i

i.

Using SST and a press, press out the rear drive pinion rear tapered roller bearing (inner) from the differential drive pinion.

SST
09555-55010  

NOTICE:

Do not drop the differential drive pinion.


HINT:

If the differential drive pinion or differential ring gear is damaged, replace them as a set.




Hide 41201B 17.REMOVE REAR DRIVE PINION FRONT BEARING (INNER)

a.
C458070


Hide 41201B 18.REMOVE REAR DRIVE PINION FRONT BEARING (OUTER)

a.
C458071C01
4.531,0.698 5.083,0.698 true 5.156,0.615 5.344,0.802 0.188,0.188 10 true *1 0.448,0.052 0.729,0.406 0.281,0.354 18 false i
*1 Rear Drive Pinion Front Tapered Roller Bearing (Outer) - -


i.

Using SST, remove the rear drive pinion front tapered roller bearing (outer) from the differential carrier.

SST
09308-00010  



Hide 41201A 19.REMOVE REAR DRIVE PINION REAR BEARING (OUTER)

a.
C458073N01
0.406,0.094 0.688,0.448 0.281,0.354 18 false i

i.

Using a brass bar and hammer, tap out the rear drive pinion rear tapered roller bearing (outer) and adjusting shim from the differential carrier.

HINT:

If the bearing is damaged during removal, replace it.




Hide 20.REMOVE DIFFERENTIAL RING GEAR

a.
C458074C01
2.542,0.948 3.042,0.948 true 2.531,0.865 2.833,0.865 2.833,0.865 2.833,0.948 true 3.104,0.854 3.333,1.083 0.229,0.229 10 false *a 4.125,0.094 4.542,0.427 0.417,0.333 18 false iii 0.167,0.083 0.75,0.417 0.583,0.333 18 false i, ii
*a Matchmark - -


i.

Place matchmarks on the differential ring gear and differential case.


ii.

Remove the 12 differential ring gear set bolts.


iii.

Using a plastic-faced hammer, tap on the differential ring gear to remove it from the differential case.

NOTICE:

Do not damage the position plate when removing the ring gear.




Hide 21.INSPECT DIFFERENTIAL CASE ASSEMBLY RUNOUT

Z101186

HINT:

If the ring gear runout is within the specified value (refer to the "Inspect Runout of Differential Ring Gear" procedure above), skip this step.



a.
C458075C01
2.188,1.052 2.5,1.208 0.313,0.156 10 false *a 0.094,0.083 0.906,0.438 0.813,0.354 18 false i - ix
*a 98 mm (3.86 in.) - -


i.

Install the rear differential case bearings (outer) to the electronic differential lock case sub-assembly.


ii.

Install the electronic differential lock case sub-assembly to the differential carrier.


iii.

Install the 2 plate washers.


iv.

Install the 2 differential bearing caps to the differential carrier with the 4 bolts.

Torque:
113 N*m (1152 kgf*cm, 83 ft.*lbf)


v.

Using a dial indicator, measure the electronic differential case runout.

Maximum runout:

0.04 mm (0.00157 in.)



vi.

Remove the 4 bolts and 2 differential bearing caps.


vii.

Remove the 2 plate washers.


viii.

Remove the electronic differential lock case sub-assembly.


ix.

Remove the rear differential case bearings (outer).



Hide 41301A 22.REMOVE REAR DIFFERENTIAL CASE BEARING (INNER)

a.
C458076C01
4.458,0.875 4.875,0.875 true 0.76,1.385 0.927,1.385 0.927,1.385 1.5,1.115 true 0.927,0.844 1.333,0.844 true 4.302,1.438 4.469,1.438 4.469,1.438 5.042,1.167 true 4.156,0.802 4.531,1 0.375,0.198 10 false SST 0.625,0.781 1,0.979 0.375,0.198 10 false SST 0.802,0.031 1.115,0.188 0.313,0.156 10 false *a 4.417,0.063 4.729,0.219 0.313,0.156 10 false *b 2.521,0.052 2.833,0.208 0.313,0.156 10 false *c 4.24,0.438 4.51,0.625 0.271,0.188 10 false *d 4.125,0.094 4.385,0.417 0.26,0.323 18 false ii 0.552,0.094 0.813,0.417 0.26,0.323 18 false i 0.646,0.417 0.917,0.604 0.271,0.188 10 false *d 6.073,0.063 6.385,0.219 0.313,0.156 10 false *c 0.406,1.281 0.781,1.479 0.375,0.198 10 false SST 3.948,1.344 4.323,1.542 0.375,0.198 10 false SST
*a for LH Side (Ring Gear Side) *b for RH Side (Differential Lock Coil Side)
*c Turn *d Hold


i.

Using SST, remove the rear differential case bearing (inner) from the electronic differential lock case sub-assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
09950-60011  (09951-00480)

HINT:

Attach the claws of SST to the notch in the differential case assembly to secure SST.



ii.

Using SST, remove the rear differential case bearing (inner) from the electronic differential lock case sub-assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04011, 09957-04010, 09958-04011)
09950-60011  (09951-00480)

HINT:
·

Attach the claws of SST to the notch in the differential case assembly to secure SST.

·
C463199

If the rear differential case bearing (inner) is removed sufficiently and the part remains on the case side, use SST as shown in the illustration and remove the relevant part.





Hide 23.REMOVE DIFFERENTIAL SOLENOID WASHER

a.
C458077N01
4.469,0.552 4.583,0.25 4.583,0.25 4.75,0.25 true 4.833,0.156 5.25,0.417 0.417,0.26 10 false SST 2.198,0.104 2.615,0.438 0.417,0.333 18 false i

i.

Tighten the 2 SST nuts evenly and remove the differential solenoid washer from the electronic differential lock case sub-assembly.

SST
09555-55010  



Hide 41451H 24.REMOVE DIFFERENTIAL LOCK COIL

a.
C458078


Hide 25.REMOVE DIFFERENTIAL LOCK PLUNGER

a.
C458079


Hide 41303E 26.DISASSEMBLE ELECTRONIC DIFFERENTIAL LOCK CASE SUB-ASSEMBLY

a.
C458080C01
6.229,0.521 6.417,0.333 6.417,0.333 6.583,0.333 true 6.25,1.5 6.438,1.313 6.438,1.313 6.604,1.313 true 6.646,0.25 6.917,0.5 0.271,0.25 10 false *1 6.677,1.208 6.906,1.427 0.229,0.219 10 false *2
*1 Differential Case LH *2 Differential Case RH



b.
C458081C01
2.177,0.677 2.594,0.677 true 4.375,1.25 4.792,1.25 true 5.375,1.594 6.125,1.594 true 2.24,0.292 2.656,0.292 true 2.719,0.219 3.031,0.375 0.313,0.156 10 false *1 2.635,0.594 2.948,0.75 0.313,0.156 10 false *2 4.094,1.177 4.406,1.333 0.313,0.156 10 false *3 6.177,1.51 6.49,1.667 0.313,0.156 10 false *3
*1 Rear Differential Pinion Thrust Washer *2 Rear No. 2 Differential Pinion Shaft
*3 Rear Differential Pinion Shaft Pin - -



c.
C458082C01
2.448,1.125 2.698,1.125 true 4.323,0.625 4.5,0.417 4.5,0.417 4.583,0.417 true 2.896,0.667 3.146,0.667 true 4.073,0.906 4.167,1.021 4.167,1.021 4.25,1.021 true 3.729,1.135 4.667,1.135 true 2.823,0.833 2.917,0.833 2.917,0.833 3,0.948 true 2.646,0.417 2.896,0.417 true 4.292,1.583 4.458,1.583 true 3.167,1.583 3.396,1.583 true 3.167,1.833 3.406,1.833 true 3.167,2.083 3.406,2.083 true 4.073,1.323 4.323,1.323 true 2.573,2.906 2.813,2.906 true 4.323,3.438 4.563,3.438 true 4.479,2.469 4.719,2.469 true 4.74,1.063 5.052,1.219 0.313,0.156 10 false *1 2.979,2.01 3.292,2.167 0.313,0.156 10 false *2 2.979,1.75 3.208,1.917 0.229,0.167 10 false *3 4.385,1.25 4.594,1.479 0.208,0.229 10 false *4 2.438,0.333 2.75,0.49 0.313,0.156 10 false *5 4.604,3.354 4.854,3.594 0.25,0.24 10 false *6 2.406,2.833 2.656,3.073 0.25,0.24 10 false *7 2.979,1.49 3.25,1.75 0.271,0.26 10 false *8 4.646,0.344 4.958,0.5 0.313,0.156 10 false *5 2.729,0.583 2.979,0.75 0.25,0.167 10 false *4 2.667,0.75 2.917,0.917 0.25,0.167 10 false *4 4.302,0.938 4.51,1.167 0.208,0.229 10 false *4 2.281,1.031 2.51,1.271 0.229,0.24 10 false *5 4.542,1.49 4.75,1.75 0.208,0.26 10 false *5 4.792,2.396 5.042,2.635 0.25,0.24 10 false *7
*1 Differential Side Gear (Dog Clutch) *2 Rear No. 2 Differential Side Gear Thrust Washer
*3 Rear No. 3 Differential Side Gear Thrust Washer *4 Differential Pinion
*5 Rear Differential Pinion Thrust Washer *6 Rear Differential Pinion Shaft
*7 Rear No. 2 Differential Pinion Shaft *8 Differential Lock Spring


i.

Remove the following parts from the differential case RH.

1.

Differential side gear (Dog clutch)

2.

Rear No. 2 differential side gear thrust washer

3.

Rear No. 3 differential side gear thrust washer

4.

Differential pinion (4 pieces)

5.

Rear differential pinion thrust washer (4 pieces)

6.

Rear differential pinion shaft

7.

Rear No. 2 differential pinion shaft (2 pieces)

8.

Differential lock spring




Hide 41474A 27.REMOVE DIFFERENTIAL LOCK POSITION PLATE

a.
C458083C01
5.844,2.448 6.177,2.448 true 6,0.5 6.333,0.5 true 6.396,0.417 6.708,0.573 0.313,0.156 10 false *1 6.25,2.344 6.563,2.5 0.313,0.156 10 false *2
*1 Differential Lock Position Plate *2 Differential Lock Cam Ring


i.

Using a T25 ''TORX'' socket wrench, remove the 3 screws from the differential lock position plate.


ii.

Remove the differential lock position plate from the differential case RH.



Hide 28.INSPECT DIFFERENTIAL GEAR KIT

a.

Check that the differential pinion and differential side gear are not damaged.

If the differential pinion or differential side gear is damaged, replace the differential gear kit.


Hide 29.INSPECT DIFFERENTIAL CASE

a.

Check that the differential case is not damaged.

If the differential case is damaged, replace it.