Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING VALVE
RM38G0E _53 Suspension _101507 TIRE PRESSURE MONITORING _0473046 TIRE PRESSURE WARNING VALVE A

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING VALVE  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C448153N01
0.073,0.104 6.469,4.729 6.396,4.625 3.271,0.271 4.99,1.823 1.719,1.552 6.469,1.063 6.719,1.063 true 3.792,1.24 4.135,1.104 4.135,1.104 4.302,1.104 true 3.479,1.01 3.479,0.531 3.479,0.531 3.646,0.531 true 5,1.031 5.25,1.031 true 5.5,4.5 5.667,4.5 5.667,4.5 5.938,4.323 true 4.5,4.167 4.667,4.167 4.667,4.167 5.76,3.99 true 2.479,3.719 5.479,3.719 true 3.021,2.51 3.208,2.51 3.208,2.51 5.344,3.5 true 0.76,0.469 0.948,0.469 0.948,0.469 1.25,0.677 true 4.344,2.052 5.063,1.927 5.063,1.927 5.292,1.927 true 3.917,1.542 4.146,1.5 4.146,1.5 4.313,1.5 true 5.708,2.646 5.708,2.396 5.708,2.396 5.875,2.396 true 6.781,0.927 7.052,1.219 0.271,0.292 18 false 1 5.594,0.896 5.865,1.188 0.271,0.292 18 false 2 5.219,4.406 5.531,4.604 0.313,0.198 10 false *1 4.135,4.073 4.5,4.271 0.365,0.198 10 false ●*2 2.219,3.656 2.531,3.854 0.313,0.198 10 false *3 2.771,2.406 3.031,2.615 0.26,0.208 10 false *4 5.344,1.844 5.708,2.042 0.365,0.198 10 false ●*5 5.917,2.313 6.229,2.51 0.313,0.198 10 false *6 0.521,0.375 0.771,0.573 0.25,0.198 10 false *7 3.688,0.448 3.948,0.646 0.26,0.198 10 false ● 4.354,1.01 4.667,1.208 0.313,0.198 10 false *8 4.354,1.385 4.75,1.594 0.396,0.208 10 false ●*9

Procedure Part Name Code
Z101186

Z101188

Z101187

1 WHEEL ASSEMBLY - - - -
2 TIRE PRESSURE WARNING VALVE AND TRANSMITTER 42607 (Click here) - -

*1 TIRE VALVE CAP *2 VALVE CORE
*3 NUT *4 WASHER
*5 GROMMET *6 DISC WHEEL
*7 TIRE *8 TIRE PRESSURE MONITOR SENSOR
*9 TUBELESS TIRE VALVE - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during tire pressure warning valve and transmitter removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Tire pressure warning valve and transmitter
·

Register transmitter ID

·

Initialize tire pressure warning system

·

Perform tire position identification


·

When DTC detection conditions of "transmitter ID not received" DTC are met, TPWS indicator blinks for 1 minute, and then illuminates.

·

Tire pressure warning function


for Initialization:
(Click here)
for Registration:
(Click here)


HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE WHEEL ASSEMBLY

Hide 42607 2.REMOVE TIRE PRESSURE WARNING VALVE AND TRANSMITTER

a.
C449978C02
2.75,2.833 3.083,2.833 true 1.25,2.865 1.583,2.865 true 0.927,2.771 1.26,2.969 0.333,0.198 10 false *1 3.135,2.76 3.448,2.917 0.313,0.156 10 false *a 2.438,3.594 2.813,3.76 0.375,0.167 10 false *b 2.792,0.073 3.292,0.365 0.5,0.292 18 true iii 0.375,0.052 0.875,0.344 0.5,0.292 18 true i, ii 5.208,0.052 5.708,0.344 0.5,0.292 18 true iv 1.438,2.052 2.125,2.354 0.688,0.302 18 true v - vii 4.104,2.042 4.563,2.333 0.458,0.292 18 true viii
*1 Tire - -
*a Shoe *b 10 to 20 mm (0.394 to 0.787 in.)


i.

Remove the tire valve cap.

NOTICE:

Keep the removed tire valve cap.



ii.

Remove the valve core to release the air from the tire.

NOTICE:

Make sure that a sufficient amount of air has been released.



iii.

Using a 11 mm deep socket wrench, remove the nut and washer.


iv.

Drop the tire pressure warning valve and transmitter with grommet into the tire.

HINT:

The grommet may remain attached to the rim.



v.

Using a tire remover, remove the tire from the disc wheel.

NOTICE:
·

Be careful not to damage the tire pressure warning valve and transmitter due to interference between the valve and the tire bead.

·

Set the tire remover shoe as shown in the illustration.




vi.

Take out the tire pressure warning valve and transmitter with grommet from the tire.


vii.

Remove the grommet from the tire pressure warning valve and transmitter.


viii.

Using a T10 "TORX" socket wrench, remove the bolt and tire pressure monitor sensor from the tubeless tire valve.