Home › Steering › POWER ASSIST SYSTEMS › VANE PUMP (for V35A-FTS)
RM38G0E _55 Steering _100915 POWER ASSIST SYSTEMS _0468432 VANE PUMP(for V35A-FTS) A

POWER ASSIST SYSTEMS  VANE PUMP(for V35A-FTS)  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (REASSEMBLY)
C457433N01
2.083,3.375 2.833,3.542 0.75,0.167 2,3.292 2.917,3.625 0.917,0.333 5.917,4.583 6.75,4.75 0.833,0.167 5.833,4.5 6.833,4.833 1,0.333 5.917,3 6.75,3.167 0.833,0.167 5.833,2.917 6.833,3.25 1,0.333 3.521,2.99 3.813,2.99 true 3.615,2.563 3.865,2.563 true 4.719,4.063 4.854,3.646 4.854,3.646 5.021,3.646 true 1.667,5.5 1.833,5.5 1.833,5.5 1.927,5.26 true 1.833,4.75 1.917,4.75 1.917,4.75 2.094,4.917 true 3.854,5.323 3.667,5.323 3.667,5.323 3.427,5.125 true 4.49,1.146 4.323,1.146 4.323,1.146 4.25,1.313 true 4.417,5.292 4.208,5.292 4.208,5.292 3.74,4.76 true 4.781,5.042 4.615,5.042 4.615,5.042 4.167,4.719 true 2.542,5.5 2.635,5.5 2.635,5.5 2.677,5.208 true 3.427,5.583 3.271,5.583 3.271,5.583 3.083,5.115 true 3.458,4.625 3.573,3.802 3.573,3.802 3.708,3.802 true 1.24,1.75 1.073,1.75 1.073,1.75 0.927,2.063 true 2.833,3.458 4,3.458 4,3.458 4,3.313 false 5.917,4.667 5.563,4.667 5.563,4.667 5.563,4.406 true 6.563,0.198 6.813,0.198 false 6.333,2.125 6.333,3 true 6.417,1.458 6.292,1.458 6.292,1.458 6.083,2.021 true 2.177,2.969 2.292,2.969 2.292,2.969 2.458,2.292 true 6.354,1.01 6.198,1.01 6.198,1.01 5.875,2.052 true 3.292,2.854 3.542,3.146 0.25,0.292 18 false 9 5.313,3.531 5.604,3.833 0.292,0.302 18 false 7 1.573,1.615 1.875,1.917 0.302,0.302 18 false 2 4.031,3.635 4.313,3.99 0.281,0.354 18 false 5 3.729,5.458 4.063,5.74 0.333,0.281 18 false 4 2.354,5.375 2.625,5.646 0.271,0.271 18 false 3 3.438,2.469 3.708,2.708 0.271,0.24 10 false ● 1.51,5.406 1.76,5.635 0.25,0.229 10 false ● 1.688,4.656 1.979,4.927 0.292,0.271 10 false ● 3.917,5.24 4.219,5.479 0.302,0.24 10 false *2 4.563,1.104 4.948,1.344 0.385,0.24 10 false *1 3.531,5.021 3.917,5.26 0.385,0.24 10 false x 10 4.875,4.927 5.167,5.198 0.292,0.271 10 false ● 5.635,4.26 6.021,4.5 0.385,0.24 10 false x 4 4.833,5.167 5.156,5.469 0.323,0.302 18 false 6 2.135,3.396 2.885,3.563 0.75,0.167 8 false 12 (122, 9) 6,4.594 7.094,4.844 1.094,0.25 8 false 22 (224, 16) 2.01,2.844 2.313,3.188 0.302,0.344 18 false 1 6.354,0.063 6.656,0.365 0.302,0.302 18 false 8 1.896,2.885 2.063,3.104 0.167,0.219 10 false ● 4.698,5.208 4.865,5.427 0.167,0.219 10 false ● 6.729,1.375 7.156,1.729 0.427,0.354 18 false 10 6.031,3.021 6.833,3.25 0.802,0.229 8 false 21 (214, 15) 6.406,0.906 6.698,1.177 0.292,0.271 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 VANE PUMP HOUSING OIL SEAL - (Click here) - -
2 VANE PUMP SHAFT WITH VANE PUMP PULLEY 44303A (Click here) - -
3 VANE PUMP SIDE PLATE - (Click here) - -
4 VANE PUMP CAM RING - (Click here) - -
5 VANE PUMP ROTOR - (Click here) - -
6 VANE PUMP SHAFT SNAP RING - (Click here) - -
7 REAR HOUSING - (Click here) - -
8 INSPECT ROTATING TORQUE - - - -
9 POWER STEERING SUCTION PORT UNION 44337 - - -
10 POWER STEERING OIL PRESSURE SENSOR 89448A (Click here) - -

*1 FRONT HOUSING *2 VANE PUMP PLATE
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) ● Non-reusable part
V100135

Power Steering Fluid
V100136

MP Grease

PROCEDURE

Hide 1.INSTALL VANE PUMP HOUSING OIL SEAL

a.
C457443C01
1.083,0.5 1.333,0.5 1.333,0.5 1.708,0.615 false 1.333,0.5 1.667,0.813 false 2.927,0.583 3.115,0.417 3.115,0.417 2.771,0.469 false 0.76,0.406 1.135,0.667 0.375,0.26 10 false SST 3.146,0.323 3.521,0.583 0.375,0.26 10 false SST 4.052,0.063 4.385,0.406 0.333,0.344 18 false ii 0.417,0.052 0.76,0.365 0.344,0.313 18 false i
V100135

MP Grease - -


i.

Using SST and a press, press in a new vane pump housing oil seal.

SST
09950-60011  (09951-00280)
09950-70010  (09951-07100)

NOTICE:
·

Make sure to install the vane pump housing oil seal so that it faces the correct direction.

·

Be careful not to damage the vane pump housing oil seal.




ii.

Coat the lip of vane pump housing oil seal with MP grease.



Hide 44303A 2.INSTALL VANE PUMP SHAFT WITH VANE PUMP PULLEY

a.
C457445C01
5.771,1.573 5.604,1.573 5.604,1.573 5.552,0.99 true 5.813,1.479 6.125,1.677 0.313,0.198 10 false *a 3.948,0.063 4.625,0.344 0.677,0.281 18 false ii, iii 0.135,0.073 0.479,0.427 0.344,0.354 18 false i
*a Protective Tape - -
V100135

Power Steering Fluid - -


i.

Coat the inside surface of the bushing in the front housing with power steering fluid.


ii.

Install the shaft with pulley to the front housing.

NOTICE:
·

Wrap protective tape around the spline of the vane pump shaft with vane pump pulley in order to prevent damage to the oil seal.

·

Be careful not to damage the vane pump housing oil seal.

·

After inserting the vane pump shaft with pulley, check that the lip of the oil seal is not inverted.




iii.

Remove the protective tape.



Hide 3.INSTALL VANE PUMP SIDE PLATE

a.
C457447C01
2.073,2.469 2.375,2.75 0.302,0.281 18 false iii 4.385,0.167 4.833,0.521 0.448,0.354 18 false ii 0.25,0.167 0.698,0.521 0.448,0.354 18 false i
V100135

Power Steering Fluid
V113147

Install in this Direction


i.

Coat a new O-ring with power steering fluid and install it to the front housing.


ii.

Coat a new O-ring with power steering fluid and install it to the vane pump side plate.


iii.

Install the vane pump side plate to the front housing while aligning the semicircle-shaped cuts of both parts.

NOTICE:

Be sure to install the vane pump side plate in the correct position and with the correct orientation.




Hide 4.INSTALL VANE PUMP CAM RING

a.
C458750C01
3.573,0.417 3.833,0.167 3.833,0.167 4,0.167 true 4.073,0.073 4.323,0.271 0.25,0.198 10 false *a 0.438,0.052 0.771,0.344 0.333,0.292 18 false i
*a Inscribed Mark - -


i.

With the inscribed mark facing upward, install the vane pump cam ring to the front housing while aligning the semicircle-shaped cuts of both parts.

NOTICE:

Be sure to install the vane pump cam ring in the correct position and with the correct orientation.




Hide 5.INSTALL VANE PUMP ROTOR

a.
C457449C01
4.542,0.688 4.75,0.333 4.75,0.333 4.833,0.333 false 1.135,0.573 1.427,0.292 1.427,0.292 1.51,0.292 false 4.542,1.271 4.854,1.427 0.313,0.156 10 false *b 4.906,0.25 5.219,0.406 0.313,0.156 10 false *c 0.333,0.115 0.729,0.438 0.396,0.323 18 false i 3.729,0.083 4.333,0.417 0.604,0.333 18 false ii, iii 1.604,0.208 1.917,0.365 0.313,0.156 10 false *a
*a Inscribed Mark *b Outward
*c Round End - -


i.

Install the vane pump rotor with the inscribed mark facing outward.


ii.

Coat the 10 vane pump plates with power steering fluid.


iii.

Install the 10 vane pump plates.

NOTICE:

Make sure that the round ends of the vane pump plates are facing outward.




Hide 6.INSTALL VANE PUMP SHAFT SNAP RING

a.
C457450N02
0.406,0.042 0.677,0.323 0.271,0.281 18 false i

i.

Using a screwdriver and snap ring expander, install a new vane pump shaft snap ring onto the pulley shaft.

NOTICE:
·

Do not expand the shaft snap ring any further than needed.

·

Make sure that the shaft snap ring is completely fit into the groove.

·

Do not damage the vane pump rotor and shaft.





Hide 7.INSTALL REAR HOUSING

a.
C457451C01
4.844,1.385 4.344,1.542 4.344,1.542 4.5,1.031 true 4.177,1.542 4.49,1.74 0.313,0.198 10 false *a 3.688,0.156 4.25,0.448 0.563,0.292 18 false ii, iii 0.167,0.167 0.76,0.531 0.594,0.365 18 false i 2.219,2 2.5,2.354 0.281,0.354 18 false iv
*a Align - -


i.

Coat the vane pump rear housing of the shaft sub-assembly with pulley and the surrounding surface with power steering fluid.


ii.

Coat a new O-ring with power steering fluid and install it to the rear housing.


iii.

Align the straight pin of the rear housing with the hole created by the semicircle-shaped cuts of the vane pump cam ring, vane pump side plate and front housing.

NOTICE:

Make sure that the O-ring is not out of position before installing the rear housing.



iv.

Install the rear housing with the 4 bolts.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)



Hide 8.INSPECT ROTATING TORQUE

a.
C457452C01
2.313,0.583 2.479,0.583 2.479,0.583 3.167,0.917 true 2.104,0.49 2.417,0.75 0.313,0.26 10 false *a 0.156,0.063 0.792,0.417 0.635,0.354 18 false i - iii
*a Service Bolt - -


i.

Check that the vane pump assembly rotates smoothly without abnormal noise.


ii.

Temporarily install the service bolt.

Recommended Service Bolt:
Item Specified Condition
Thread Diameter 10 mm (0.394 in.)
Thread Pitch 1.25 mm (0.0492 in.)
Bolt Length 50 mm (1.97 in.)



iii.

Using a torque wrench, check the pump rotating torque.

Standard rotating torque:

0.3 N*m (3 kgf*cm, 3 in.*lbf) or less


If the rotating torque is not as specified, check the assembling state of the vane pump assembly.



Hide 44337 9.INSTALL POWER STEERING SUCTION PORT UNION

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

Hide 89448A 10.INSTALL POWER STEERING OIL PRESSURE SENSOR

a.
C462620C02
0.427,0.094 0.698,0.354 0.271,0.26 18 false i 4.365,0.104 4.604,0.427 0.24,0.323 18 false ii
V100135

Power Steering Fluid - -


i.

Apply a light coat of power steering fluid to the a new O-ring of the power steering oil pressure sensor.


ii.

Install the power steering oil pressure sensor.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:
·

Do not allow foreign matter to contact the oil seal face of the power steering oil pressure sensor (the surface that contacts the pressure feed tube).

·

Be careful not to damage the O-ring when installing the power steering oil pressure sensor.