Home › Engine / Hybrid System › V35A-FTS (FUEL) › FUEL PUMP (for Double Tank Type)
RM38G0E _51 Engine / Hybrid System _101368 V35A-FTS FUEL _0474713 FUEL PUMP(for Double Tank Type) A

V35A-FTS FUEL  FUEL PUMP(for Double Tank Type)  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (REASSEMBLY)
A487477N02
3.156,3.854 3.646,3.854 false 6.313,1.865 6.729,1.865 false 0.917,3.573 1.667,3.573 false 2.958,2.354 3.26,2.354 false 1.844,0.708 2.594,0.708 false 3.771,0.708 4.438,0.708 false 2.865,1.375 3.281,1.375 false 2.313,1.646 2.813,1.646 false 0.729,3.417 0.969,3.688 0.24,0.271 18 false 5 3.594,0.563 3.833,0.833 0.24,0.271 18 false 4 3.688,3.698 3.927,3.969 0.24,0.271 18 false 3 1.667,0.563 1.906,0.833 0.24,0.271 18 false 2 3.563,2.219 3.74,2.479 0.177,0.26 18 false 1 3.323,1.26 3.719,1.458 0.396,0.198 10 false ● *1 2.135,1.563 2.448,1.76 0.313,0.198 10 false *2 6.75,1.76 7.063,1.958 0.313,0.198 10 false *3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FUEL WITH FILTER PUMP ASSEMBLY 23320A (Click here) - -
2 NO. 1 FUEL SUCTION SUPPORT 77174 - - -
3 NO. 1 FUEL SUB-TANK 77131C - - -
4 FUEL SUCTION PLATE SUB-ASSEMBLY 77024A - - -
5 FUEL SENDER GAUGE ASSEMBLY 83320 - - -

*1 O-RING *2 FUEL PUMP SPACER
*3 FUEL PUMP HARNESS - -
● Non-reusable part
V100135

Gasoline

CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the fuel with filter pump assembly.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 23220A 1.INSTALL FUEL WITH FILTER PUMP ASSEMBLY

Z101186

HINT:

Perform "Inspection After Repair" after replacing the fuel with filter pump assembly.

Click here(Click here)



a.
A487653N01
0.854,0.094 1.073,0.344 0.219,0.25 18 false i 4.031,0.094 4.25,0.344 0.219,0.25 18 false ii

i.

Attach the claw and install the fuel pump harness.

NOTICE:
·

Securely attach the claw.

·

Make sure that there is no foreign matter between the fuel pump and the ground terminal of the fuel pump harness.

·

Make sure that the ground terminal of the fuel pump harness is securely connected to the fuel pump body.




ii.

Check the connection state of the fuel pump harness.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Fuel pump body - Ground terminal of the fuel pump harness Always Below 50 Ω


If the result is not as specified, reconnect the fuel pump harness to the fuel pump so that the ground terminal of the fuel pump harness is securely connected to the fuel pump body.



b.
A487654C01
2.865,0.615 3.438,0.615 true 2.677,0.51 2.885,0.688 0.208,0.177 10 false *a
*a Apply gasoline - -



c.
A487479


Hide 77174 2.INSTALL NO. 1 FUEL SUCTION SUPPORT

Hide 77131C 3.INSTALL NO. 1 FUEL SUB-TANK

a.
A487481


Hide 77024A 4.INSTALL FUEL SUCTION PLATE SUB-ASSEMBLY

a.
A487483