If the radio receiver assembly cannot detect the navigation ECU assembly for a certain period of time (90 seconds) after the ignition switch is turned to ACC and the radio receiver assembly confirms that the information is missing by checking past navigation ECU assembly recognition information (registered information), this DTC will be stored.
The audio and visual system uses USB communication between devices. If an open, short, short to +B or short to ground occurs in the USB circuit, communication is interrupted and the audio and visual system will not operate normally.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B1543 | Extension Module Disconnected 2 | Navigation ECU assembly disconnected |
·
Navigation ECU assembly
·
Radio receiver assembly
·
Harness or connector |
Navigation System | A |
This DTC may be stored due to environmental reasons such as electrical noise or interference.
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Inspect the fuses for circuits related to this system before performing the following procedure.
Pre-procedure1
Turn the ignition switch to ACC and wait for 90 seconds.
Procedure1
Press the "MAP" switch and check that the map screen is displayed normally.
| Result | Proceed to |
|---|---|
| Map screen is displayed normally | A |
| Map screen is not displayed normally | B |
This DTC may be stored due to environmental reasons such as electrical noise or interference.
Clear past DTCs when the map screen is displayed normally. (Codes stored due to past environmental factors)
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Pre-procedure1
Clear the DTCs.
Turn the ignition switch off.
Turn the ignition switch to ON and wait for 90 seconds.
Procedure1
Recheck for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Pre-procedure1
Disconnect the I21 navigation ECU assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I21)Location & Routingewd_type=routing;type=c;code=I21 |
||
| I21-23 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I21)Location & Routingewd_type=routing;type=c;code=I21 |
||
| I21-10 (+B) - Body ground | Always | 10.5 to 16 V*1 |
| 11 to 14 V*2 | ||
*1: w/ Stop and Start System
*2: w/o Stop and Start System
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the I157 radio receiver assembly connector.
Disconnect the I158 navigation ECU assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I157,I158)Location & Routingewd_type=routing;type=c,c;code=I157,I158 |
||
| I157-4 (US4+) - I158-4 (US4+) | Always | Below 1 Ω |
| I157-5 (US4-) - I158-5 (US4-) | Always | Below 1 Ω |
| I157-6 (UGD4) - I158-6 (UGD4) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Replace the navigation ECU assembly with a new or known good one.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Clear the DTCs.
Turn the ignition switch off.
Turn the ignition switch to ON and wait for 90 seconds.
Procedure1
Recheck for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
Post-procedure1
None
A
B
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio Receiver Type)>REMOVAL