The integration control sub-assembly and radio receiver assembly are connected by AVC-LAN communication lines.
This DTC is stored when an AVC-LAN communication error occurs between the integration control sub-assembly and radio receiver assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B15D6 | Display Disconnected | A device that is listed in the AVC-LAN connected device record of the master unit is missing |
·
Integration control sub-assembly power source circuit
·
AVC-LAN circuit between radio receiver assembly and integration control sub-assembly
·
Integration control sub-assembly
·
Radio receiver assembly
·
Harness or connector |
Navigation System | A |
The radio receiver assembly is the master unit.
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Inspect the fuses for circuits related to this system before performing the following procedure.
When replacing the integration control sub-assembly, always replace it with a new one. If an integration control sub-assembly which was installed to another vehicle is used, the following may occur:
A communication malfunction DTC may be stored.
The integration control sub-assembly may not operate normally.
Check for optional components.
Check that optional components (including associated wiring) which generate radio waves are not installed.
Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.
| Result | Proceed to |
|---|---|
| Optional components (including associated wiring) are installed. | A |
| Optional components (including associated wiring) are not installed. | B |
A
B
Remove optional components (including associated wiring).
Do not remove optional components or associated wiring without the permission of the customer.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Clear the DTCs.
Procedure1
Recheck for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
Post-procedure1
None
A
B
Pre-procedure1
Disconnect the I22 integration control sub-assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I22)Location & Routingewd_type=routing;type=c;code=I22 |
||
| I22-20 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I22)Location & Routingewd_type=routing;type=c;code=I22 |
||
| I22-1 (B) - I22-20 (GND) | Always | 11 to 14 V*1 |
| 10.5 to 16 V*2 | ||
| I22-3 (ACC) - I22-20 (GND) | Ignition switch ACC | 11 to 14 V*1 |
| 10.5 to 16 V*2 | ||
| I22-4 (IG+) - I22-20 (GND) | Ignition switch ON | 11 to 14 V*1 |
| 10.5 to 16 V*2 | ||
*1: w/o Stop and Start System
*2: w/ Stop and Start System
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the I10 radio receiver assembly connector.
Procedure1
| *a | Component without harness connected (Radio Receiver Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (TX1+) - 6 (TX1-) | Always | 60 to 80 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio Receiver Type)>REMOVAL
Pre-procedure1
Disconnect the I10 radio receiver assembly connector.
Disconnect the I22 integration control sub-assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I10,I22)Location & Routingewd_type=routing;type=c,c;code=I10,I22 |
||
| I10-5 (TX1+) - I22-36 (TX1+) | Always | Below 1 Ω |
| I10-6 (TX1-) - I22-35 (TX1-) | Always | Below 1 Ω |
| I10-5 (TX1+) or I22-36 (TX1+) - Body ground | Always | 10 kΩ or higher |
| I10-6 (TX1-) or I22-35 (TX1-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Replace the integration control sub-assembly with a new one.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>MULTI-DISPLAY ECU>REMOVAL
Clear the DTCs.
Procedure1
Recheck for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
Post-procedure1
None
A
B
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio Receiver Type)>REMOVAL