Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type, for 12.3 Inch Display)
RM38G0E _56 Audio / Visual / Telematics _100606 AUDIO / VIDEO _0467496 AUDIO AND VISUAL SYSTEM(for Radio and Display Type, for 12.3 Inch Display) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type, for 12.3 Inch Display)  B15D9  Operation Panel Disconnected  


DESCRIPTION

The air conditioning control assembly (switch and volume) and integration control sub-assembly are connected by an AVC-LAN communication line. When an AVC-LAN communication error occurs between the integration control sub-assembly and air conditioning control assembly (switch and volume), this DTCs will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B15D9 Operation Panel Disconnected A device that is listed in the AVC-LAN connected device record of the master unit is missing.
·

Air conditioning control assembly (switch and volume) power source circuit

·

AVC-LAN circuit

·

Air conditioning control assembly (switch and volume)

·

Integration control sub-assembly

·

Radio receiver assembly

·

Harness or connector


Navigation System A

HINT:

For the AVC-LAN communication line, the Radio receiver assembly is the master unit.


WIRING DIAGRAM

E462726E03
3.094,3.75 5.208,4.125 2.115,0.375 10 false Air Conditioning Control Assembly (Switch and Volume) 3.094,3.573 3.542,3.771 0.448,0.198 10 false I78 5.521,3.76 6.688,4.323 1.167,0.563 10 false Integration Control Sub-assembly 5.521,3.594 6.667,3.875 1.146,0.281 10 false I22 5.563,1.323 5.948,1.5 0.385,0.177 10 false TX3+ 5.573,1.885 5.938,2.094 0.365,0.208 10 false TX3- 4.344,1.354 4.729,1.573 0.385,0.219 10 false TX+ 4.354,1.885 4.719,2.083 0.365,0.198 10 false TX- 0.844,4.344 2.854,4.542 2.01,0.198 10 false : AVC-LAN Communication Line 3.51,3 3.677,3.177 0.167,0.177 10 false E 3.51,1.354 3.75,1.552 0.24,0.198 10 false +B 3.5,1.854 3.865,2.021 0.365,0.167 10 false ACC 3.51,2.385 3.76,2.583 0.25,0.198 10 false IG+ 0.948,1.365 1.969,1.625 1.021,0.26 10 false from Battery*2 0.719,1.844 2.042,2.083 1.323,0.24 10 false from ACC Relay*2 0.354,2.385 1.99,2.625 1.635,0.24 10 false from IGR-NO. 2 Relay*2 2.167,1.51 3.313,1.792 1.146,0.281 10 false ECU-B NO.3 2.302,2.021 3.448,2.302 1.146,0.281 10 false ECU-ACC 2.188,2.563 3.333,2.844 1.146,0.281 10 false ECU-IGR NO.2 3.25,1.208 4.396,1.49 1.146,0.281 10 false 16 3.292,1.708 4.438,1.99 1.146,0.281 10 false 7 3.26,2.25 4.406,2.531 1.146,0.281 10 false 8 4.708,1.229 5.031,1.417 0.323,0.188 10 false 1 4.719,1.802 4.979,2 0.26,0.198 10 false 2 5.281,1.229 5.531,1.438 0.25,0.208 10 false 13 5.281,1.802 5.531,1.99 0.25,0.188 10 false 11 3.292,2.927 4.438,3.208 1.146,0.281 10 false 4 0.125,0.354 1.51,0.854 1.385,0.5 10 false from Engine Stop and Start ECU*1 2.906,4.333 4.917,4.531 2.01,0.198 10 false *1: w/ Stop and Start System 5.031,4.344 7.156,4.542 2.125,0.198 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuse for circuits related to this system before performing the following procedure.


HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type, for 12.3 Inch Display)>PRECAUTION


PROCEDURE

1.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check for optional components.

i.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result:
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B


HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

·

This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.






A

2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY [SWITCH AND VOLUME] - BATTERY AND BODY GROUND)
2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.



Result:
Proceed to
NEXT



NEXT

3.CHECK DTC
3.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

END (COMMUNICATION MALFUNCTION DUE TO NOISE)

B

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY [SWITCH AND VOLUME] - BATTERY AND BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY [SWITCH AND VOLUME] - BATTERY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the I78 air conditioning control assembly (switch and volume) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I78)Location & Routing

Click Connector(I78)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Air Conditioning Control Assembly

I78-4 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

*1: w/ Stop and Start System

*2: w/o Stop and Start System

Click Location & Routing(I78)Location & Routing

Click Connector(I78)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Air Conditioning Control Assembly

I78-16 (+B) - Body ground Always 10.5 to 16 V*1
11 to 14 V*2
I78-7 (ACC) - Body ground Ignition switch ACC 10.5 to 16 V*1
11 to 14 V*2
I78-8 (IG+) - Body ground Ignition switch ON 10.5 to 16 V*1
11 to 14 V*2



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY [SWITCH AND VOLUME] - INTEGRATION CONTROL SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY [SWITCH AND VOLUME] - INTEGRATION CONTROL SUB-ASSEMBLY)

Pre-procedure1

a.

Disconnect the I78 air conditioning control assembly (switch and volume) connector.


b.

Disconnect the I22 integration control sub-assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I78,I22)Location & Routing

Click Connector(I78)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Air Conditioning Control Assembly

Click Connector(I22)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Integration Control Sub-Assembly

I78-1 (TX+) - I22-13 (TX3+) Always Below 1 Ω
I78-2 (TX-) - I22-11 (TX3-) Always Below 1 Ω
I78-1 (TX+) - Body ground Always 10 kΩ or higher
I78-2 (TX-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

6.CHECK AIR CONDITIONING CONTROL ASSEMBLY (SWITCH AND VOLUME)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK AIR CONDITIONING CONTROL ASSEMBLY (SWITCH AND VOLUME)

Pre-procedure1

a.

Replace the air conditioning control assembly (switch and volume) with a new or known good one.

HINT:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL (for Front Side)>REMOVAL



b.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

procedure1

c.

Recheck for DTCs and check that no DTCs are output.

Procedure1

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
DTCs are not output A
DTCs are output B


Post-procedure1

d.

None



A

END (AIR CONDITIONING CONTROL ASSEMBLY [SWITCH AND VOLUME] IS DEFECTIVE)

B

7.CHECK INTEGRATION CONTROL SUB-ASSEMBLY
7.CHECK INTEGRATION CONTROL SUB-ASSEMBLY

Pre-procedure1

a.

Replace the integration control sub-assembly with a new or known good one.

HINT:

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>MULTI-DISPLAY>REMOVAL



b.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Procedure1

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
DTCs are not output A
DTCs are output B


Post-procedure1

d.

None



A

END (INTEGRATION CONTROL SUB-ASSEMBLY IS DEFECTIVE)

B