Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › REAR SEAT SIDE AIRBAG ASSEMBLY (for LH Side) › from 2021.07
RM38G0E _58 Vehicle Interior _100751 SUPPLEMENTAL RESTRAINT SYSTEMS _0467883 REAR SEAT SIDE AIRBAG ASSEMBLY(for LH Side) N

SUPPLEMENTAL RESTRAINT SYSTEMS  REAR SEAT SIDE AIRBAG ASSEMBLY(for LH Side)  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


PROCEDURE

Hide 1. PRECAUTION

CAUTION:
·

An airbag or pretensioner may be accidentally deployed by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.

·
B394953

Never dispose of a rear seat airbag assembly with an undeployed airbag.

·

The airbag produces an exploding sound when it is deployed, so perform the operation outdoors where it will not disturb nearby residents.

B436767

·

When deploying the airbag, always use the specified SST (SRS airbag deployment tool). Perform the operation in a place away from electrical noise.

·

When deploying the airbag, perform the operation at least 10 m (32.8 ft.) away from the rear seat airbag assembly LH.

·

The rear seat airbag assembly LH becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a rear seat airbag assembly LH with a deployed airbag.

·

Do not apply water, etc. to a rear seat airbag assembly LH with a deployed airbag.

·

Always wash your hands with water after completing the operation.



HINT:

When scrapping a vehicle equipped with an SRS or disposing of the rear seat airbag assembly LH, be sure to deploy the airbag first in accordance with the following procedure. If any abnormality occurs with the airbag deployment, contact the Service Department of the distributor.


Hide 2.DISPOSE OF REAR SEAT AIRBAG ASSEMBLY LH (When Installed to Vehicle)

NOTICE:
·

When disposing of a rear seat airbag assembly LH, never use the customer's vehicle to deploy the airbag.

·

Be sure to perform the following procedure when deploying the airbag.



HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371N08
0.99,1.208 0.792,0.771 0.792,0.771 0.646,0.771 false 0.323,0.688 0.781,0.885 0.458,0.198 10 SST

Check the function of SST.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>DISPOSAL

SST
09082-00700  



c.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:
B422343

·

Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.





d.

Remove the rear seat No. 2 cushion hinge cover.

Click hereVehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for LH Side)>REMOVAL


e.

Remove the rear seat No. 4 cushion hinge cover.

Click hereVehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for LH Side)>REMOVAL


f.

Disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



g.

Install SST.

i.
B609832

Connect SST to the rear seat airbag assembly LH.

SST
09082-00820  


ii.
B611406

Pass SST through the gap shown in the illustration.


iii.

Operate the rear No. 1 seat assembly LH to its sitting position.

CAUTION:
B609840

Check that there is no looseness in the rear seat airbag assembly LH.



iv.
B609834N01
1.313,1.375 1.313,1.167 true 0.563,1.385 0.563,1.167 0.563,1.167 1.427,1.167 true 1.448,1.073 1.781,1.281 0.333,0.208 10 true SST

Connect SST together (09082-00700 and 09082-00820).

SST
09082-00700  

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock.



v.
C154370C17
1.76,0.552 1.99,0.25 1.99,0.25 2.188,0.25 false 0.458,1.167 0.677,1.167 false 0.677,1.167 0.927,1.396 false 2.229,0.167 2.542,0.323 0.313,0.156 10 false *a 1.594,1.802 1.906,1.958 0.313,0.156 10 false *b 0.177,1.104 0.573,1.323 0.396,0.219 10 false SST
*a Battery
*b 10 m (32.8 ft.) or more


Move SST at least 10 m (32.8 ft.) away from the front side window of the vehicle.


vi.

Maintaining sufficient clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.

NOTICE:

Take care not to damage the SST wire harness.



vii.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.



h.

Deploy the airbag.

i.

Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.


ii.

Press the SST activation switch to deploy the airbag.

CAUTION:
·
B400936

Before deployment, make sure that no one is inside or near the vehicle.

·
B609842

The rear seat airbag assembly LH becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·
B609844

Use gloves and safety glasses when handling a rear seat airbag assembly LH with a deployed airbag.

·
B609846

Do not apply water, etc. to a rear seat airbag assembly LH with a deployed airbag.

·

Always wash your hands with water after completing the operation.



HINT:

The airbag is deployed as the LED of the SST activation switch comes on.




Hide 3.DISPOSE OF REAR SEAT AIRBAG ASSEMBLY LH (When not Installed to Vehicle)

NOTICE:

Be sure to perform the following procedure when deploying the airbag.


HINT:

Prepare a 12 V battery as the power source to deploy the airbag.


a.
C110371N08
0.99,1.208 0.792,0.771 0.792,0.771 0.646,0.771 false 0.323,0.688 0.781,0.885 0.458,0.198 10 SST

Check the function of SST.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>DISPOSAL

SST
09082-00700  


b.

Remove the rear seat airbag assembly LH.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>REAR SEAT SIDE AIRBAG ASSEMBLY (for LH Side)>REMOVAL

CAUTION:
·
B399378C08
0.615,0.531 0.771,0.729 0.156,0.198 10 false .
V100155

Deployment Side


When storing the rear seat airbag assembly LH, keep the airbag deployment side facing upward.




c.
B104882C16
2.313,0.938 2.052,0.427 2.052,0.427 1.875,0.427 false 2.656,1.469 2.896,1.646 0.24,0.177 10 *a 1.635,0.333 1.844,0.521 0.208,0.188 10 *b
*a Wire Diameter
*b Stripped Wire Cross Sectional Area


Using braided wire, tie down the rear seat airbag assembly LH to an unneeded tire.

Wire:

Stripped Wire Cross Sectional Area

1.25 mm2 (0.0019 in.2) or more


CAUTION:

If the wire is too thin or an alternative object is used to tie down the rear seat airbag assembly LH, it may snap when the airbag is deployed. Always use a wire for vehicle use with a cross sectional area of at least 1.25 mm2 (0.0019 in.2).


HINT:

To calculate the cross sectional area of the stripped wire:

Cross sectional area = 3.14 x (Diameter)2 / 4


i.
B279752

Install the 2 nuts to the rear seat airbag assembly LH.


ii.
B279753

Wind 2 or more wires around the stud bolts of the rear seat airbag assembly LH as shown in the illustration.


iii.
B279754C04
0.625,1.438 0.938,1.594 0.313,0.156 10 false *a 1.208,0.01 1.521,0.167 0.313,0.156 10 false *b
*a Inner Diameter
*b Width


Position the rear seat airbag assembly LH inside the tire with the airbag deployment side facing inward.

Minimum tire size:
Width:

185 mm (7.28 in.)

Inner diameter:

360 mm (1.18 ft.)


CAUTION:
·

Make sure that the wires are tight. If there is slack in the wires, the rear seat airbag assembly LH may break loose when the airbag is deployed.

·
B399353C04
0,0 0,0 false
V100155

Deployment Side


Always tie down the rear seat airbag with the airbag deployment side facing inside the tire as shown in the illustration.



NOTICE:

The tire may be damaged by the airbag deployment, so use an unneeded tire.




d.

Install SST.

i.
B279755E07
2.646,1.396 2.854,1.396 false 2.906,1.323 3.292,1.542 0.385,0.219 10 SST

Connect the SST connector to the rear seat airbag assembly LH connector.

SST
09082-00820  



e.

Place the tires.

i.
B289035C04
2.396,1.479 2.563,1.677 0.167,0.198 10 false *a 2.396,0.656 2.563,0.854 0.167,0.198 10 false *a 1.604,0.073 1.813,0.24 0.208,0.167 10 false *b 0.865,0.833 1.031,1.031 0.167,0.198 10 false *c
*a Tires (2 or more)
*b Inner Diameter
*c Width


Place at least 2 tires under the tire to which the rear seat airbag assembly LH is tied.

Minimum tire size:
Width:

185 mm (7.28 in.)

Inner diameter:

360 mm (1.18 ft.)


NOTICE:

Do not place the SST connector under the tire because it could be damaged.



ii.

Place at least 2 tires onto the tire to which the rear seat airbag assembly LH is tied. The top tire should have a wheel installed.

NOTICE:

The wheel and tires may be damaged by the airbag deployment, so use an unneeded wheel and tires.



iii.
C223306

Tie the tires together with 2 wires.

CAUTION:

Make sure that the wires are tight. Looseness in the wires will result in the tires breaking loose when the airbag is deployed.




f.

Install SST.

i.
B279757C06
1.417,1.99 1.635,1.99 false 0.365,2.781 0.365,2.938 false 0.219,2.969 0.542,3.156 0.323,0.188 10 false SST 1.198,2.969 1.427,3.177 0.229,0.208 10 false *b 1.677,1.917 1.906,2.094 0.229,0.177 10 false *a
*a Battery
*b 10 m (32.8 ft.) or more


Connect the SST connector.

SST
09082-00700  

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the tire.



ii.

Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the tire.



g.

Deploy the airbag.

i.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.


ii.

Check that no one is within a 10 m (32.8 ft.) radius of the tire to which the rear seat airbag assembly LH is tied.


iii.

Press the SST activation switch to deploy the airbag.

CAUTION:
B401768

Before deployment, make sure that no one is near the airbag.


HINT:

The airbag is deployed as the LED of the SST activation switch comes on.




h.

Dispose of the rear seat airbag assembly LH.

CAUTION:
·
B428382

The rear seat airbag assembly LH becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·
B428384

Use gloves and safety glasses when handling a rear seat airbag assembly LH with a deployed airbag.

·
B428383

Do not apply water, etc. to a rear seat airbag assembly LH with a deployed airbag.

·

Always wash your hands with water after completing the operation.



i.

Remove the rear seat airbag assembly LH from the tire.


ii.

Place the rear seat airbag assembly LH in a plastic bag, tie it tightly, and dispose of it according to local regulations.