Home › General › MAINTENANCE › V35A-FTS BATTERY
RM38G0E _V1 General _100461 MAINTENANCE _0470509 V35A-FTS BATTERY A

MAINTENANCE  V35A-FTS BATTERY  REMOVAL  


CAUTION / NOTICE / HINT

A484843N01
6.677,0.208 6.885,0.208 false 0.365,1.75 0.531,1.75 false 2.573,0.813 2.74,0.813 false 1.083,1.198 1.333,1.198 false 1.177,2.667 1.469,2.667 false 2.26,2.906 2.51,2.906 false 2.333,1.833 2.5,1.833 false 2.385,1.25 2.792,1.25 false 6.521,0.063 6.802,0.417 0.281,0.354 18 false 1 0.167,1.646 0.448,2 0.281,0.354 18 false 2 2.823,0.677 3.104,1.031 0.281,0.354 18 false 4 0.896,1.073 1.177,1.427 0.281,0.354 18 false 6 1,2.531 1.281,2.885 0.281,0.354 18 false 7 2.573,2.792 2.854,3.146 0.281,0.354 18 false 8 2.813,1.677 3.365,2.031 0.552,0.354 18 false 10 0.073,0.031 0.385,0.229 0.313,0.198 10 false *A 2.156,2.281 2.615,2.479 0.458,0.198 10 false x 3 2.833,1.167 3.146,1.365 0.313,0.198 10 false *1 0.271,0.021 0.583,0.219 0.313,0.198 10 false *B

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 ENGINE SIDE COVER RH 51473C - - -
4 COWL TOP VENTILATOR LOUVER RH 55781D - - -
6 CABLE FROM NEGATIVE BATTERY TERMINAL - - - -
7 CABLE FROM POSITIVE BATTERY TERMINAL - - - -
8 NO. 2 BATTERY CLAMP SUB-ASSEMBLY 74405 - - -
10 BATTERY 28800 (Click here) - -

*A for LHD - -
*1 HOOD TO COWL TOP SEAL - -

A484842N01
6.625,0.208 6.875,0.208 false 0.75,1.75 0.917,1.75 false 2.406,1.219 2.719,1.219 false 0.323,3 0.573,3 false 1.865,3.083 2.198,3.083 false 1.844,2.156 1.917,1.854 1.917,1.854 2,1.854 false 1.135,3.375 1.25,3.5 1.25,3.5 1.333,3.5 false 1.177,1.135 1.458,1.135 false 6.458,0.052 6.74,0.406 0.281,0.354 18 false 1 0.552,1.635 0.833,1.99 0.281,0.354 18 false 3 2.813,1.073 3.094,1.427 0.281,0.354 18 false 5 2.063,1.74 2.344,2.094 0.281,0.354 18 false 6 0.156,2.896 0.438,3.25 0.281,0.354 18 false 7 1.406,3.365 1.688,3.719 0.281,0.354 18 false 9 2.51,3 3.063,3.354 0.552,0.354 18 false 10 0.052,0.031 0.365,0.229 0.313,0.198 10 false *A 1.208,2.406 1.667,2.604 0.458,0.198 10 false x 2 0.969,1.052 1.281,1.25 0.313,0.198 10 false *1 0.25,0.031 0.563,0.229 0.313,0.198 10 false *B

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
3 ENGINE SIDE COVER LH 51474B - - -
5 COWL TOP VENTILATOR LOUVER LH 55782D - - -
6 CABLE FROM NEGATIVE BATTERY TERMINAL - - - -
7 CABLE FROM POSITIVE BATTERY TERMINAL - - - -
9 NO. 2 BATTERY CLAMP 74482 - - -
10 BATTERY 28800 (Click here) - -

*A for RHD - -
*1 HOOD TO COWL TOP SEAL - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during the battery removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click here(Click here)

·

When replacing the battery, use a new battery of the same dimensions and same capacity or more from the same class at a 20-hour rate.




Hide 51473C 2.REMOVE ENGINE SIDE COVER RH (for LHD)

Hide 51474B 3.REMOVE ENGINE SIDE COVER LH (for RHD)

Hide 55781D 4.DISCONNECT COWL TOP VENTILATOR LOUVER RH (for LHD)

a.
A493844


Hide 55782D 5.DISCONNECT COWL TOP VENTILATOR LOUVER LH (for RHD)

a.

Use the same procedure as for LHD.


Hide 6.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

a.
A488302C01
0.448,0.042 0.76,0.24 0.313,0.198 10 false *A 3.917,0.021 4.229,0.219 0.313,0.198 10 false *B
*A for LHD *B for RHD



Hide 7.DISCONNECT CABLE FROM POSITIVE BATTERY TERMINAL

a.
A488303C01
0.406,0.031 0.719,0.229 0.313,0.198 10 false *A 3.833,0.021 4.146,0.219 0.313,0.198 10 false *B
*A for LHD *B for RHD



Hide 74405 8.REMOVE NO. 2 BATTERY CLAMP SUB-ASSEMBLY (for LHD)

a.
A484851


Hide 74482 9.REMOVE NO. 2 BATTERY CLAMP (for RHD)

a.

Use the same procedure as for LHD.


Hide 28800 10.REMOVE BATTERY

Z101186

HINT:
·

for LHD:

When removing the battery, it can be temporarily placed on top of the No. 1 engine room relay block and junction block assembly.

·

for RHD:

When removing the battery, it can be temporarily placed on top of the No. 2 engine room relay block and junction block assembly.


NOTICE:
·

for LHD:

Protect the No. 1 engine room relay block and junction block assembly and air cleaner cap sub-assembly to prevent damage.

·

for RHD:

Protect the No. 2 engine room relay block and junction block assembly and air cleaner cap sub-assembly to prevent damage.






a.
A488304C01
0.365,0.042 0.677,0.24 0.313,0.198 10 false *A 3.833,0.031 4.146,0.229 0.313,0.198 10 false *B
*A for LHD *B for RHD