Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › OUTSIDE STRIPE › from 2021.07
RM38G0E _59 Vehicle Exterior _100846 EXTERIOR PANELS / TRIM _0484672 OUTSIDE STRIPE A

EXTERIOR PANELS / TRIM  OUTSIDE STRIPE  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B617207N01
4.75,3.417 4.583,3.417 4.583,3.417 4.5,3 false 6.51,0.229 6.844,0.229 false 4.969,3.323 5.125,3.521 0.156,0.198 10 false ● 6.344,0.104 6.615,0.375 0.271,0.271 18 false 1 5.115,3.302 5.385,3.573 0.271,0.271 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REPAIR INSTRUCTION - (Click here) - -
2 BACK DOOR STRIPE 75945 (Click here) - -

● Non-reusable part - -

PROCEDURE

Hide 1. REPAIR INSTRUCTION

a.
B599854C03
6.396,0.854 6.49,0.698 false 6.667,1.385 6.76,1.229 false 1.146,2.583 1.24,2.427 false 2.844,3.073 3,3.208 false 4.885,3.542 5.094,3.542 false 3.531,3.729 3.625,3.844 false 1.667,3.74 1.781,3.865 false 0.865,4.844 0.823,4.927 false 0.323,0.802 0.281,0.885 false 5.677,3.615 5.792,3.74 false 1.688,5.469 1.813,5.344 false 4.688,5.281 4.875,5.073 true 2.865,3.552 3.094,3.646 false 1.115,3.375 1.344,3.469 false 0.896,1.865 1.219,2.115 0.323,0.25 12 false *A 2.927,1.854 3.25,2.104 0.323,0.25 12 false *B 0.49,0.198 0.813,0.448 0.323,0.25 18 false i 2.521,0.208 2.844,0.458 0.323,0.25 18 false ii 3.729,0.198 4.052,0.448 0.323,0.25 18 false iii 6.063,0.188 6.385,0.438 0.323,0.25 18 false iv 0.542,1.823 0.865,2.073 0.323,0.25 18 false v 4.698,1.823 5.021,2.073 0.323,0.25 18 false vi 0.427,4.302 0.75,4.552 0.323,0.25 18 false vii 4.719,4.333 5.042,4.583 0.323,0.25 18 false viii 6.49,0.573 6.802,0.771 0.313,0.198 10 false *1 6.49,1.333 6.802,1.531 0.313,0.198 10 false *1 5.792,0.646 6.104,0.844 0.313,0.198 10 false *a 5.802,1.063 6.115,1.26 0.313,0.198 10 false *b 4.042,0.208 4.354,0.406 0.313,0.198 10 false *b 4.865,0.208 5.177,0.406 0.313,0.198 10 false *a 5.938,4.448 6.25,4.646 0.313,0.198 10 false *b 5.938,4.865 6.25,5.063 0.313,0.198 10 false *b 5.938,5.271 6.25,5.469 0.313,0.198 10 false *a 1.021,2.594 1.333,2.792 0.313,0.198 10 false *c 2.677,2.938 2.99,3.135 0.313,0.198 10 false *c 4.729,3.458 5.042,3.656 0.313,0.198 10 false *c 1.75,3.875 2.063,4.073 0.313,0.198 10 false *d 3.594,3.865 3.906,4.063 0.313,0.198 10 false *d 5.979,3.354 6.292,3.552 0.313,0.198 10 false *e 1.688,4.531 2,4.729 0.313,0.198 10 false *f 0.729,4.917 1.042,5.115 0.313,0.198 10 false *g 0.198,0.875 0.51,1.073 0.313,0.198 10 false *g 1.646,2.125 1.958,2.323 0.313,0.198 10 false *i 3.323,3.521 3.635,3.719 0.313,0.198 10 false *j 2.25,2.865 2.573,3.063 0.323,0.198 10 false *l 3.979,2.885 4.302,3.083 0.323,0.198 10 false *l 5.833,3.698 6.146,3.896 0.313,0.198 10 false *1 0.677,2.594 0.99,2.792 0.313,0.198 10 false *k 2.885,2.583 3.198,2.781 0.313,0.198 10 false *k 1.531,5.427 1.844,5.625 0.313,0.198 10 false *1 4.875,4.927 5.188,5.125 0.313,0.198 10 false *1 0.938,3.292 1.25,3.49 0.313,0.198 10 false *1 2.688,3.458 3,3.656 0.313,0.198 10 false *1 2.927,0.76 3.24,0.958 0.313,0.198 10 false *h
*A Pressing Forward *B Pulling
*1 Back Door Stripe - -
*a Correct *b Incorrect
*c Squeegee *d Release Paper
*e Hem *f Corner
*g Heat Light *h 20 to 30°C (68 to 86°F)
*i 40 to 50° (for pressing forward) *j 30 to 45° (for pulling)
*k 30 to 70 mm/sec. (1.19 to 2.75 in./sec.) *l 10 to 20 mm (0.394 to 0.787 in.)


i.

Clean the vehicle body surface

1. Using a heat light, heat the vehicle body surface.

Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body excessively.


2. Wipe off any back door stripe adhesive residue with cleaner.


ii.

Installation temperature

1. When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and back door stripe up to between 20 to 30°C (68 to 86°F) using a heat light. When the ambient temperature is above 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and back door stripe down to between 20 to 30°C (68 to 86°F) prior to installation.

HINT:
·

The most appropriate temperature for installing the back door stripe is 25°C (77°F).

·

When the temperature is low, the back door stripe becomes stiff and comes off easily. When the temperature is high, the back door stripe elasticity increases.




iii.

Before installation

1. Remove any coating roughness or dirt on and around the vehicle body surface where the back door stripe will be installed (installation surface of the door frame). If any roughness or dirt remains when pressing the back door stripe onto the surface, air will be trapped under the back door stripe and result in a poor appearance.

HINT:

Spray water on the shop floor to settle any dust.



iv.

Key points for handling the back door stripe

1. The back door stripe bends and rolls up easily. Store the back door stripe between flat pieces of cardboard or other similar objects and keep it dry and flat.

NOTICE:

Do not bend the back door stripe or leave it in high temperature places.



v.

Key points for installation of the back door stripe (How to use a squeegee and installation procedure for flat surfaces)

To avoid air bubbles, slightly raise the part of the back door stripe that is going to be applied so that its adhesive surface does not touch the vehicle body prematurely. Tilt the squeegee at 40 to 50° (pressing forward) or 30 to 45° (pulling) to the vehicle body surface and press the back door stripe onto the vehicle body surface with a force of 20 to 30 N (2 to 3 kgf, 4.5 to 6.7 lbf) at a constant slow speed of 30 to 70 mm (1.19 to 2.75 in.) per second.

NOTICE:
·

Position the back door stripe accurately to achieve a neat finish and to avoid peeling.

·

The back door stripe cannot be reused because it deforms after removal.

·

Be sure to observe the specified pressing speed, force and angle of the squeegee to avoid wrinkles or air bubbles.



HINT:
·

Either angle of the squeegee (pressing forward or pulling) is acceptable.

·

Be sure to apply the back door stripe while removing the release paper 10 to 20 mm (0.394 to 0.787 in.) from the edge of the squeegee.




vi.

Key points for installation of the back door stripe (How to use a squeegee and installation procedure for hemmed surfaces)

1. If it is difficult to apply the back door stripe, install it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the back door stripe to the hem of the vehicle, especially for a small hem.

HINT:

When applying back door stripe to the backside of a hem, remove the release paper and use your fingers or the padded surface of a squeegee.



vii.

Key points for installation of the back door stripe (How to use a squeegee and installation procedure for corners)

1. Remove the release paper and apply the back door stripe carefully with your fingers.

2. Before applying the back door stripe to each corner, heat the back door stripe using a heat light and gradually apply it, avoiding wrinkles on the back door stripe to achieve a neat finish.


viii.

Check after installation

After completing the installation, check if the back door stripe is installed neatly. If the back door stripe is not installed neatly, install a new back door stripe.

NOTICE:

Do not reuse the back door stripe.




Hide 75945 2.INSTALL BACK DOOR STRIPE

Z101186

NOTICE:

When installing the back door stripe, heat the back door panel and back door stripe using a heat light.



Standard Value:
Part Temperature
Back Door Panel 40 to 60°C (104 to 140°F)
Back Door Stripe 20 to 30°C (68 to 86°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the back door panel and back door stripe excessively.


a.
B620144C03
6.479,4.865 6.281,4.865 6.281,4.865 6.208,4.333 true 6.698,4.083 6.479,4.083 6.479,4.083 6.406,4.25 false 6.698,4.552 6.531,4.552 6.531,4.552 6.26,4.292 true 0.583,0.667 0.865,1.021 0.281,0.354 18 false i 0.583,1.813 0.865,2.167 0.281,0.354 18 false ii 0.5,3.646 0.781,4 0.281,0.354 18 false iii 6.583,3.375 6.823,3.625 0.24,0.25 10 false *a 6.573,4.781 6.885,4.979 0.313,0.198 10 false *c 6.729,4.458 7.042,4.656 0.313,0.198 10 false *b 4.875,4.646 5.115,4.896 0.24,0.25 10 false *a 6.75,3.99 7.063,4.188 0.313,0.198 10 false *d
*a 3 mm (0.118 in.) *b Curve end of Back Door Panel
*c Edge of Back Door Stripe *d Application Tape


i.

Clean the surface of the back door panel.

1. Using a heat light, heat the back door panel surface.

2. Remove any remaining double-sided tape from the back door panel.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the back door stripe with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Using a heat light, heat the back door panel and back door stripe.


iii.

Align the application tape of the back door stripe with the edge of back door panel and install the back door stripe as shown in the illustration.

NOTICE:

Attach so that the distance from the end of the back door stripe to the back door panel rounded end is 3 mm (0.118 in.).




b.
B620160C02
4.333,4.719 4.167,4.219 4.167,4.219 3.917,4.219 false 3.5,3.083 3.833,2.917 3.833,2.917 4.083,2.917 false 3.75,2.667 4.083,2.583 4.083,2.583 4.333,2.583 false 3.865,3.667 3.698,3.667 3.698,3.667 3.448,3.167 true 1.906,4.917 2.156,4.5 2.156,4.5 2.323,4.5 false 2.302,5.427 2.052,5.427 2.052,5.427 1.885,5.01 false 2.115,4.167 2.448,3.917 2.448,3.917 2.698,3.917 false 4.417,4.75 4.75,4.583 4.75,4.583 5,4.583 false 4.927,4.948 5.26,4.781 5.26,4.781 5.51,4.781 false 0.396,0.031 0.677,0.385 0.281,0.354 18 false i 3.427,1.781 3.583,1.979 0.156,0.198 10 true B 4,1 4.156,1.198 0.156,0.198 10 true A 3.99,1.354 4.146,1.552 0.156,0.198 10 true A 3.427,1.417 3.583,1.615 0.156,0.198 10 true B 6.063,1.76 6.219,1.958 0.156,0.198 10 true C 5.76,1.635 5.917,1.833 0.156,0.198 10 true C 4.115,5.542 4.573,5.74 0.458,0.198 10 false C-C 3.292,3.823 3.75,4.021 0.458,0.198 10 false A-A 1.625,5.552 2.083,5.75 0.458,0.198 10 false B-B 4.448,4.198 4.76,4.396 0.313,0.198 10 false *a 2.375,4.969 2.688,5.167 0.313,0.198 10 false *a 3.823,3.375 4.135,3.573 0.313,0.198 10 false *a 2.385,5.354 2.698,5.552 0.313,0.198 10 false *b 5.083,4.5 5.396,4.698 0.313,0.198 10 false *b 4.177,2.865 4.49,3.063 0.313,0.198 10 false *b 2.781,3.844 3.094,4.042 0.313,0.198 10 false *d 3.719,4.146 4.031,4.344 0.313,0.198 10 false *c 2.406,4.438 2.719,4.635 0.313,0.198 10 false *c 3.948,3.583 4.26,3.781 0.313,0.198 10 false *c 5.604,4.719 5.917,4.917 0.313,0.198 10 false *d 4.427,2.51 4.74,2.708 0.313,0.198 10 false *d
*a 3 mm (0.118 in.) *b Curve end of Back Door Panel End
*c Edge of Back Door Stripe *d Application Tape
V113147

Install in this Direction - -


i.

Fold the application tape into the back door panel backside, align and apply it.

HINT:

Apply pressure so that it does not lift up from the back door panel.




c.

Using a squeegee, press the back door stripe.


d.

Remove the application tape.