Home › Engine / Hybrid System › F33A-FTV (ENGINE MECHANICAL) › CYLINDER HEAD › from 2021.07
RM38G0E _51 Engine / Hybrid System _106330 F33A-FTV ENGINE MECHANICAL _0485593 CYLINDER HEAD G

F33A-FTV ENGINE MECHANICAL  CYLINDER HEAD  INSPECTION  


PROCEDURE

Hide 11101 1.CLEAN CYLINDER HEAD SUB-ASSEMBLY

a.

Using a gasket scraper, remove all the gasket material from the cylinder block sub-assembly contact surface.

NOTICE:

Be careful not to scratch the cylinder block sub-assembly contact surface.



b.
A164826

Using a wire brush, remove all the carbon from the combustion chambers.

NOTICE:

Be careful not to damage the combustion chambers and valve seats.



c.
A164841

Using a valve guide bushing brush and solvent, clean all the valve guide bushes.


d.

Using a soft brush and solvent, thoroughly clean the cylinder head sub-assembly.


Hide 11101 2.INSPECT CYLINDER HEAD SUB-ASSEMBLY

a.

Using a precision straightedge and feeler gauge, measure the warpage of the contact surfaces where the cylinder head sub-assembly contacts the cylinder block sub-assembly and manifolds.

Maximum Warpage:
Item Specified Condition
Cylinder Block Sub-assembly Side 0.05 mm (0.00197 in.)
Intake Manifold Side 0.10 mm (0.00394 in.)
Exhaust Crossover Pipe Sub-assembly Side 0.10 mm (0.00394 in.)

A492145C01
3.969,0.469 4.281,0.625 0.313,0.156 10 false *a 3.979,1.75 4.292,1.906 0.313,0.156 10 false *b 3.99,2.833 4.302,2.99 0.313,0.156 10 false *c
*a Cylinder Block Sub-assembly Side *b Exhaust Crossover Pipe Sub-assembly Side
*c Intake Manifold Side - -


If the warpage is more than the maximum, replace the cylinder head sub-assembly.


b.

Using a dye penetrant, check the intake ports, exhaust ports and cylinder surface for cracks. If there are cracks, replace the cylinder head sub-assembly.


Hide 13711M 3.INSPECT INTAKE VALVE COMPRESSION SPRING

a.
A400451C09
1.656,0.156 1.969,0.354 0.313,0.198 10 false *a 0.948,1.219 1.26,1.417 0.313,0.198 10 false *b
*a Deviation
*b 41.39 mm (1.630 in.)


Inspect the intake valve compression spring deviation.

i.

Using a steel square, measure the deviation of the intake valve compression spring.

Maximum deviation:

1.0 mm (0.0394 in.)


If the deviation is more than the maximum, replace the intake valve compression spring.



b.
A101392

Inspect the intake valve compression spring free length.

i.

Using a vernier caliper, measure the free length of the intake valve compression spring.

Standard free length:

55.80 mm (2.197 in.)


If the free length is not as specified, replace the intake valve compression spring.



c.
EM00281

Inspect the intake valve compression spring tension.

i.

Using a spring tester, measure the tension of the intake valve compression spring at the specified installed length.

Installed tension:

257 to 284 N (26 to 29 kgf, 57.8 to 63.8 lbf) at 38.9 mm (1.53 in.)


If the installed tension is not as specified, replace the intake valve compression spring.



Hide 13715H 4.INSPECT EXHAUST VALVE COMPRESSION SPRING

a.
A400451C10
1.74,0.156 2.052,0.313 0.313,0.156 10 false *a 0.979,1.26 1.292,1.417 0.313,0.156 10 false *b
*a Deviation
*b 45.06 mm (1.774 in.)


Inspect the exhaust valve compression spring deviation.

i.

Using a steel square, measure the deviation of the exhaust valve compression spring.

Maximum deviation:

1.0 mm (0.0394 in.)


If the deviation is more than the maximum, replace the exhaust valve compression spring.



b.
A101392

Inspect the exhaust valve compression spring free length.

i.

Using a vernier caliper, measure the free length of the exhaust valve compression spring.

Standard free length:

59.07 mm (2.326 in.)


If the free length is not as specified, replace the exhaust valve compression spring.



c.
EM00281

Inspect the exhaust valve compression spring tension.

i.

Using a spring tester, measure the tension of the exhaust valve compression spring at the specified installed length.

Installed tension:

219 to 242 N (22 to 25 kgf, 49.2 to 54.4 lbf) at 38.3 mm (1.51 in.)


If the installed tension is not as specified, replace the exhaust valve compression spring.



Hide 13711 5.CLEAN VALVE

a.

Using a gasket scraper, chip off any carbon from the valve head.

NOTICE:

Be careful not to damage the valve seats.



b.

Using a wire brush, thoroughly clean the valve.


Hide 13715 6.INSPECT VALVE

a.
A415293

Using a micrometer, measure the diameter of the valve stem.

Standard Valve Stem Diameter:
Item Specified Condition
Intake 5.470 to 5.485 mm (0.2154 to 0.2159 in.)
Exhaust 5.465 to 5.480 mm (0.2152 to 0.2157 in.)


b.
A131998C04
0.427,1.698 0.615,1.917 0.188,0.219 10 false *a
*a Margin Thickness


Inspect the valve head margin thickness.

i.

Using a vernier caliper, measure the valve head margin thickness.

Standard margin thickness:

1.0 mm (0.0394 in. )


Minimum margin thickness:

0.5 mm ( 0.0197 in. )


If the margin thickness is less than the minimum, replace the valve.



c.
A415295C03
2.427,0.99 2.74,1.188 0.313,0.198 10 false *a
*a Overall Length


Inspect the valve overall length.

i.

Using a vernier caliper, measure the overall length.

Standard Overall Length:
Item Specified Condition
Intake 103.00 mm (4.06 in.)
Exhaust 101.95 mm (4.01 in.)

Minimum Overall Length:
Item Specified Condition
Intake 102.50 mm (4.04 in.)
Exhaust 101.45 mm (3.99 in.)

If the overall length is less than the minimum, replace the valve.



d.

Inspect the valve stem tip.

i.

Check the surface of the valve stem tip for wear.

NOTICE:

Do not grind the valve so it becomes shorter than the minimum overall length.


If the valve stem tip is worn, resurface the tip with a grinder or replace the valve.



Hide 11122B 7.INSPECT VALVE GUIDE BUSH OIL CLEARANCE

a.
A164580

Using a caliper gauge, measure the inside diameter of the valve guide bush.

Standard Valve Guide Bush Inside Diameter:

5.510 to 5.530 mm (0.217 to 0.218 in.)



b.

Subtract the valve stem diameter measurement from the valve guide bush inside diameter measurement.

Standard Oil Clearance:
Item Specified Condition
Intake 0.025 to 0.060 mm (0.000984 to 0.00236 in.)
Exhaust 0.030 to 0.065 mm (0.00118 to 0.00256 in.)


Maximum Oil Clearance:
Item Specified Condition
Intake 0.11 mm (0.00433 in.)
Exhaust 0.12 mm (0.00472 in.)


If the oil clearance is more than the maximum, replace the valve and valve guide bush.


Hide 8.CLEAN VALVE SEAT

a.

Using a 45° carbide cutter, resurface the valve seats.

NOTICE:

Be careful not to damage the combustion chambers and valve seats.



b.

Clean the valve seats.


Hide 9.INSPECT INTAKE VALVE SEAT

a.

Apply a light coat of Prussian blue to the intake valve face.


b.

Lightly press the intake valve face against the intake valve seat.

NOTICE:

Do not rotate the intake valve while pressing it.



c.
A415299C02
1.427,1.229 1.615,1.427 0.188,0.198 10 false *a
*a Width


Check the intake valve face and intake valve seat by using the following procedure:

i.

If Prussian blue appears 360° around the entire intake valve face, the valve face is concentric.

If the valve face is not concentric, replace the intake valve.


ii.

If Prussian blue appears 360° around the entire intake valve seat, the intake valve seat and valve face are concentric.

If the valve face is not concentric, resurface the intake valve seat.


iii.

Measure the width of the contact area of the intake valve seat and valve face.

Standard Width:

1.2 to 1.6 mm (0.0472 to 0.0630 in.)




Hide 10.INSPECT EXHAUST VALVE SEAT

a.

Apply a light coat of Prussian blue to the exhaust valve face.


b.

Lightly press the exhaust valve face against the exhaust valve seat.

NOTICE:

Do not rotate the exhaust valve while pressing it.



c.
A415300C02
1.438,1.25 1.656,1.458 0.219,0.208 10 false *a
*a Width


Check the exhaust valve face and exhaust valve seat by using the following procedure:

i.

If Prussian blue appears 360° around the entire exhaust valve face, the valve face is concentric.

If the valve face is not concentric, replace the exhaust valve.


ii.

If Prussian blue appears 360° around the entire exhaust valve seat, the exhaust valve seat and valve face are concentric.

If the valve face is not concentric, resurface the exhaust valve seat.


iii.

Measure the width of the contact area of the exhaust valve seat and valve face.

Standard Width:

1.2 to 1.6 mm (0.0472 to 0.0630 in.)




Hide 13501B 11.INSPECT INTAKE CAMSHAFT SUB-ASSEMBLY THRUST CLEARANCE

a.

Install the No. 2 and No. 5 camshaft bearing caps to the cylinder head sub-assembly.


b.

Place the intake camshaft sub-assembly RH and intake camshaft sub-assembly LH on the cylinder head sub-assembly.


c.
A492146C01
0,0 0,0 false

Temporarily install the No. 1 and No. 4 camshaft bearing caps with the 4 bolts by hand.

NOTICE:

Do not turn the intake camshaft sub-assembly RH and intake camshaft sub-assembly LH.



d.

Install the No. 3 camshaft bearing caps.

i.
A492147C01
0.375,0.573 0.688,0.729 0.313,0.156 10 false *A 0.333,2.354 0.646,2.51 0.313,0.156 10 false *B
*A for Bank 1
*B for Bank 2


Confirm the marks and numbers on the No. 3 camshaft bearing caps and place them in their proper position and direction.


ii.

Temporarily install the 12 bolts.



e.
A492148C03
0.375,0.219 0.583,0.385 0.208,0.167 10 false 8 0.104,0.073 0.417,0.229 0.313,0.156 10 false *A 0.115,2.469 0.427,2.625 0.313,0.156 10 false *B 0.323,0.677 0.531,0.844 0.208,0.167 10 false 7 0.406,1.531 0.615,1.698 0.208,0.167 10 false 9 0.354,2.042 0.563,2.208 0.208,0.167 10 true 10 1.146,0.167 1.354,0.333 0.208,0.167 10 true 4 1.167,1.427 1.375,1.594 0.208,0.167 10 true 3 1.771,1.427 1.979,1.594 0.208,0.167 10 true 1 1.75,0.177 1.958,0.344 0.208,0.167 10 true 2 2.375,0.177 2.583,0.344 0.208,0.167 10 true 6 2.396,1.417 2.552,1.583 0.156,0.167 10 true 5 0.385,2.542 0.594,2.708 0.208,0.167 10 false 10 0.417,3.073 0.625,3.24 0.208,0.167 10 false 9 0.417,3.927 0.552,4.083 0.135,0.156 10 true 7 0.427,4.427 0.635,4.594 0.208,0.167 10 false 8 1.281,3.135 1.49,3.302 0.208,0.167 10 true 3 1.292,4.417 1.5,4.583 0.208,0.167 10 true 4 1.958,4.406 2.177,4.573 0.219,0.167 10 true 2 1.917,3.177 2.125,3.344 0.208,0.167 10 true 1 2.563,3.188 2.771,3.354 0.208,0.167 10 true 5 2.583,4.427 2.792,4.594 0.208,0.167 10 true 6
*A for Bank 1
*B for Bank 2


Uniformly tighten the 20 bolts in several steps in the order shown in the illustration.

Torque:

for 12 mm head bolt of No. 1 and No. 4 camshaft bearing cap:

21 N*m (214kgf*cm, 15 ft. *lbf)

for 10 mm head bolt of No. 3 camshaft bearing cap:

10 N*m (102 kgf*cm, 7ft. *lbf)



f.
A495388

Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

Standard thrust clearance:

0.035 to 0.160 mm (0.00138 to 0.00630 in.)


Maximum thrust clearance:

0.180 mm (0.00709 in.)


If the thrust clearance is more than the maximum, replace the intake camshaft sub-assembly RH and intake camshaft sub-assembly LH.

If necessary, replace the cylinder head sub-assembly.


Hide 13502C 12.INSPECT EXHAUST CAMSHAFT SUB-ASSEMBLY THRUST CLEARANCE

a.

Install the No. 2 and No. 5 camshaft bearing caps to the cylinder head sub-assembly.


b.

Place the exhaust camshaft sub-assembly RH and exhaust camshaft sub-assembly LH on the cylinder head sub-assembly.


c.
A492149C01
0,0 0,0 false

Temporarily install the No. 1 and No. 4 camshaft bearing caps with the 4 bolts by hand.

NOTICE:

Do not turn the exhaust camshaft sub-assembly RH and exhaust camshaft sub-assembly LH.



d.

Install the No. 3 camshaft bearing caps.

i.
A492150C01
0.396,0.198 0.708,0.354 0.313,0.156 10 false *A 0.417,2.813 0.729,2.969 0.313,0.156 10 false *B
*A for Bank 1
*B for Bank 2


Confirm the marks and numbers on the No. 3 camshaft bearing caps and place them in their proper position and direction.


ii.

Temporarily install the 12 bolts.



e.
A492151C03
0.323,0.146 0.635,0.344 0.313,0.198 10 false 10 0.385,0.656 0.698,0.854 0.313,0.198 10 false 9 0.396,2 0.708,2.198 0.313,0.198 10 false 8 0.385,1.49 0.521,1.656 0.135,0.167 10 true 7 0.385,2.583 0.698,2.781 0.313,0.198 10 false 8 0.365,3.125 0.677,3.323 0.313,0.198 10 false 7 0.406,3.958 0.719,4.156 0.313,0.198 10 false 9 0.333,4.427 0.646,4.625 0.313,0.198 10 false 10 1.135,0.698 1.385,0.854 0.25,0.156 10 true 3 1.156,2.031 1.406,2.188 0.25,0.156 10 true 4 1.823,0.708 2.073,0.865 0.25,0.156 10 true 1 1.854,2.042 2.104,2.198 0.25,0.156 10 true 2 2.49,2.031 2.74,2.188 0.25,0.156 10 true 6 2.5,0.75 2.75,0.906 0.25,0.156 10 true 5 1.313,2.563 1.563,2.719 0.25,0.156 10 true 4 1.979,2.563 2.229,2.719 0.25,0.156 10 true 2 2.656,2.583 2.906,2.74 0.25,0.156 10 true 6 1.302,3.875 1.552,4.031 0.25,0.156 10 true 3 1.99,3.854 2.24,4.01 0.25,0.156 10 true 1 2.656,3.875 2.906,4.031 0.25,0.156 10 true 5 0.094,0.104 0.406,0.26 0.313,0.156 10 false *A 0.125,2.49 0.438,2.646 0.313,0.156 10 false *B
*A for Bank 1
*B for Bank 2


Uniformly tighten the 20 bolts in several steps in the order shown in the illustration.

Torque:

for 12 mm head bolt of No. 1 and No. 4 camshaft bearing cap

21 N*m (214kgf*cm, 15 ft.*lbf)

for 10 mm head bolt of No. 3 camshaft bearing cap

10 N*m (102 kgf*cm, 7ft.*lbf)



f.
A492152C01
0,0 0,0 false

Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

Standard thrust clearance:

0.035 to 0.160 mm (0.00138 to 0.00630 in.)


Maximum thrust clearance:

0.180 mm (0.00709 in.)


If the thrust clearance is more than the maximum, replace the exhaust camshaft sub-assembly RH and exhaust camshaft sub-assembly LH. If necessary, replace the cylinder head sub-assembly.