Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for Toyota Connected Services) › from 2021.07
RM38G0E _56 Audio / Visual / Telematics _100608 TELEMATICS _0484974 TELEMATICS SYSTEM(for Toyota Connected Services) C

TELEMATICS  TELEMATICS SYSTEM(for Toyota Connected Services)  B157213  Microphone Circuit Open  


DESCRIPTION

This DTC is stored when a communication telematics box signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B157213 Microphone Circuit Open Current at terminal MCVD exceeds the malfunction threshold for 10 seconds or more while the ignition switch is ON
·

Telephone transceiver assembly

·

Telephone microphone assembly

·

Harness or connector


Telematics A

WIRING DIAGRAM

E364325E61
1.406,0.823 1.969,1.031 0.563,0.208 10 false MCVD 1.469,1.271 1.906,1.479 0.438,0.208 10 false MCI+ 1.5,1.74 1.917,1.948 0.417,0.208 10 false MCI- 1.417,2.198 1.896,2.417 0.479,0.219 10 false SGND 1.896,0.833 2.25,1.042 0.354,0.208 10 false 5 1.896,1.271 2.323,1.49 0.427,0.219 10 false 6 1.896,1.74 2.208,1.979 0.313,0.24 10 false 7 1.896,2.198 2.25,2.417 0.354,0.219 10 false 23 0.49,2.771 0.948,2.979 0.458,0.208 10 false I55 0.479,2.958 2.51,3.167 2.031,0.208 10 false Telephone Transceiver Assembly 3.948,0.823 4.26,1.031 0.313,0.208 10 false 1 3.958,1.281 4.25,1.49 0.292,0.208 10 false 2 3.958,1.74 4.26,1.979 0.302,0.24 10 false 4 4.156,0.833 4.719,1.042 0.563,0.208 10 false MACC 4.156,1.281 4.719,1.49 0.563,0.208 10 false MCO+ 4.177,1.74 4.74,1.948 0.563,0.208 10 false MCO- 4.083,2.625 4.521,2.844 0.438,0.219 10 false d30 4.083,2.813 6.781,3.073 2.698,0.26 10 false Telephone Microphone Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System (for Toyota Connected Services).

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for Toyota Connected Services)>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.



PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 10 seconds or more.


b.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

Procedure1

c.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

d.

None



A

B

2.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)

Pre-procedure1

a.

Disconnect the I55 telephone transceiver assembly connector.


b.

Disconnect the d30 telephone microphone assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I55,d30)Location & Routing

Click Connector(I55)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Telematics Transceiver Assembly

Click Connector(d30)Body>No. 1 Roof Wire>Telephone Microphone Assembly RH

I55-5 (MCVD) - d30-1 (MACC) Always Below 1 Ω
I55-6 (MCI+) - d30-2 (MCO+) Always Below 1 Ω
I55-7 (MCI-) - d30-4 (MCO-) Always Below 1 Ω
I55-23 (SGND) - Body ground Always 10 kΩ or higher
I55-5 (MCVD) - Body ground Always 10 kΩ or higher
I55-6 (MCI+) - Body ground Always 10 kΩ or higher
I55-7 (MCI-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

3.CHECK TELEPHONE TRANSCEIVER ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TELEPHONE TRANSCEIVER ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY POWER SOURCE)

Pre-procedure1

a.

Remove the telephone microphone assembly but do not disconnect the connectors.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE MICROPHONE ASSEMBLY>REMOVAL



Procedure1

b.
E364326C29
1.5,0.219 1.885,0.448 0.385,0.229 2.458,1.844 2.198,1.333 true 1.083,1.823 1.458,1.375 true 1.583,0.26 1.885,0.438 0.302,0.177 10 false d30 0.198,0.167 0.427,0.354 0.229,0.188 10 false *a 2.292,1.865 2.708,2.021 0.417,0.156 10 false MACC 0.865,1.844 1.281,2 0.417,0.156 10 false MCO-
*a Component with harness connected
(Telephone Microphone Assembly)


Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(d30)Location & Routing

Click Connector(d30)Body>No. 1 Roof Wire>Telephone Microphone Assembly RH

d30-1 (MACC) - Body ground Ignition switch ON 4 to 6 V


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(d30)Location & Routing

Click Connector(d30)Body>No. 1 Roof Wire>Telephone Microphone Assembly RH

d30-4 (MCO-) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

NG

4.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
4.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL



Result:
Proceed to
NEXT



NEXT