Home › Power Source / Network › F33A-FTV (BATTERY / CHARGING) › GENERATOR (for VALEO Made) › from 2021.07
RM38G0E _57 Power Source / Network _106328 F33A-FTV BATTERY / CHARGING _0489035 GENERATOR(for VALEO Made) A

F33A-FTV BATTERY / CHARGING  GENERATOR(for VALEO Made)  REASSEMBLY  


CAUTION / NOTICE / HINT

A484905N01
5.344,0.49 6.344,0.698 1,0.208 4.083,2.5 5.083,2.667 1,0.167 2.844,0.99 3.833,1.156 0.99,0.167 3.083,2.135 3.167,2.385 3.167,2.385 3.25,2.385 false 5.406,2.25 5.5,2.5 5.5,2.5 5.583,2.5 false 1,1.5 1.083,1 1.083,1 1.167,1 false 6.333,0.583 6.417,0.583 6.417,0.583 6.417,1.469 false 3.865,1.708 4,2.583 4,2.583 4.083,2.583 false 3.833,1.083 3.917,1.083 3.917,1.083 3.917,1.438 false 3.688,2.302 3.969,2.656 0.281,0.354 18 false 1 5.667,2.396 5.948,2.75 0.281,0.354 18 false 2 1.25,0.917 1.563,1.115 0.313,0.198 10 false *1 5.406,0.521 6.365,0.646 0.958,0.125 8 false 3.3 (34, 29 in.*lbf) 4.135,2.51 5.115,2.719 0.979,0.208 8 false 4.3 (44, 38 in.*lbf) 2.917,1 3.906,1.198 0.99,0.198 8 false 4.3 (44, 38 in.*lbf) 3.948,1.583 4.406,1.781 0.458,0.198 10 false x 2 6.542,1.438 7,1.635 0.458,0.198 10 false x 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 GENERATOR REGULATOR ASSEMBLY 27700A (Click here) - -
2 GENERATOR REAR END COVER 27039 - - -

*1 GENERATOR ASSEMBLY - -
V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

PROCEDURE

Hide 27700A 1.INSTALL GENERATOR REGULATOR ASSEMBLY

a.
A484909C01
1.031,0.625 1.198,0.125 1.198,0.125 1.365,0.125 true 2.385,0.729 2.552,0.313 2.552,0.313 2.719,0.313 true 5.583,0.167 5.667,0.167 5.667,0.167 6,0.333 false 1.385,0.031 1.698,0.229 0.313,0.198 10 false *a 2.75,0.229 3.063,0.427 0.313,0.198 10 false *a 5.396,0.083 5.708,0.281 0.313,0.198 10 false *a 0.458,0.01 0.74,0.365 0.281,0.354 18 false i 3.802,0.042 4.438,0.375 0.635,0.333 18 false ii, iii
*a Pin (1.0 mm) - -
V100145

Brush
V100155

Generator Regulator Assembly Cover
V100135

Push down
V100136

Pull out


i.

While pushing the 2 brushes into the generator regulator assembly, insert a 1.0 mm (0.0394 in.) pin into the generator regulator assembly as shown in the illustration.


ii.

Push down the generator regulator assembly cover and secure the 2 brushes as shown in the illustration.


iii.

Pull out the pin from the generator regulator assembly.



b.
A484910C01
1.365,0.469 1.677,0.667 0.313,0.198 10 false *a 1.417,0.833 1.604,0.99 0.188,0.156 10 true *a 2.792,0.458 3.104,0.656 0.313,0.198 10 false *b 0.625,0.135 0.979,0.406 0.354,0.271 18 false i 4.156,0.125 4.708,0.479 0.552,0.354 18 false ii
*a Bolt *b Stud Bolt
V100136

Push in - -


i.

Install the generator regulator assembly with the 2 bolts and stud bolt.

Torque:
4.3 N*m (44 kgf*cm, 38 in.*lbf)


ii.

Push in the generator regulator assembly cover as shown in the illustration.



Hide 27039 2.INSTALL GENERATOR REAR END COVER

Torque:
3.3 N*m (34 kgf*cm, 29 in.*lbf)