Home › Engine / Hybrid System › F33A-FTV (STARTING) › STARTER (w/ Stop And Start System) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106336 F33A-FTV STARTING _0489153 STARTER(w/ Stop And Start System) A

F33A-FTV STARTING  STARTER(w/ Stop And Start System)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A493812N01
6.635,0.198 6.885,0.198 false 6.677,0.583 6.844,0.583 false 1,1.083 1.417,1.083 false 1.5,2.25 1.573,2.5 1.573,2.5 1.667,2.5 false 1.99,3.021 2.156,2.771 2.156,2.771 2.24,2.771 false 3.427,3.229 3.76,3.479 3.76,3.479 3.844,3.479 false 4.375,2.958 4.833,3.156 0.458,0.198 10 false x 3 1.458,1.573 1.917,1.771 0.458,0.198 10 false x 2 6.448,0.031 6.729,0.385 0.281,0.354 18 false 1 6.479,0.396 6.76,0.75 0.281,0.354 18 false 2 0.844,0.958 1.125,1.313 0.281,0.354 18 false 3 1.729,2.354 2.01,2.708 0.281,0.354 18 false 4 2.333,2.646 2.615,3 0.281,0.354 18 false 5 4.219,3.333 4.5,3.688 0.281,0.354 18 false 6

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL - - - -
3 FRONT EXHAUST PIPE SUB-ASSEMBLY 17401 - - -
4 OIL COOLER TUBE SUB-ASSEMBLY - - - -
5 ENGINE WIRE 82121 - - -
6 STARTER ASSEMBLY 28100 (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the starter assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Starter assembly
NOTICE:

When the starter assembly is replaced, "ST NO. 1 relay" must be also replaced.


Clear number of starter operations Stop and start system (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click here(Click here)

·

When the starter assembly is replaced, "ST NO. 1 relay" must be also replaced.




Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 4.DISCONNECT OIL COOLER TUBE SUB-ASSEMBLY

a.
A488306


Hide 82121 5.DISCONNECT ENGINE WIRE

a.
A488307


Hide 28100 6.REMOVE STARTER ASSEMBLY

Z101186

NOTICE:

When the starter assembly is replaced, "ST NO. 1 relay" must be also replaced.



a.
A488308