Home › Engine / Hybrid System › F33A-FTV (STARTING) › GLOW PLUG › from 2021.07
RM38G0E _51 Engine / Hybrid System _106336 F33A-FTV STARTING _0489159 GLOW PLUG A

F33A-FTV STARTING  GLOW PLUG  REMOVAL  


CAUTION / NOTICE / HINT

A498681N01
6.51,0.188 6.906,0.188 false 6.615,0.594 6.844,0.594 false 0.469,0.979 0.719,0.979 false 0.656,2.99 0.979,2.99 false 2.635,1.292 2.833,1.292 2.833,1.292 3.146,1.813 false 1.844,1.927 2.219,1.927 false 1.844,2.354 2.167,2.354 false 2.844,0.802 3.104,0.802 false 6.063,0.042 6.521,0.396 0.458,0.354 18 false 1, 2 6.385,0.417 6.667,0.771 0.281,0.354 18 false 3 0.281,0.802 0.563,1.156 0.281,0.354 18 false 4 0.927,1.552 1.385,1.75 0.458,0.198 10 false x 3 1.813,0.719 2.271,0.917 0.458,0.198 10 false x 2 0.448,2.844 0.729,3.198 0.281,0.354 18 false 6 1.438,3.469 1.896,3.667 0.458,0.198 10 false x 2 2.344,2.302 2.802,2.5 0.458,0.198 10 false x 3 2.563,2.135 3.021,2.333 0.458,0.198 10 false x 3 3.177,1.823 3.635,2.021 0.458,0.198 10 false x 3 2.01,1.104 2.563,1.458 0.552,0.354 18 false 12 1.24,1.75 1.677,2.115 0.438,0.365 18 false 10 1.646,2.208 1.927,2.563 0.281,0.354 18 false 9 3.167,0.646 3.448,1 0.281,0.354 18 false 7 0.063,0.063 0.375,0.26 0.313,0.198 10 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

1 WARM UP ENGINE - (Click here) - -
2 PRECAUTION - (Click here) - -
3 DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL - - - -
4 FRONT FENDER APRON TRIM PACKING C 53784 - - -
6 STARTER HOSE BRACKET SUB-ASSEMBLY 28101 - - -
7 INTAKE MANIFOLD INSULATOR 17853B - - -
9 GLOW PLUG SCREW GROMMET 19850B - - -
10 NO. 1 GLOW PLUG CONNECTOR 19871 (Click here) - -
12 GLOW PLUG ASSEMBLY 19850 (Click here) - -

*A BANK 1 - -

A498675N02
5.219,0.917 5.656,0.917 false 5.25,3 5.667,3 false 4.792,2.083 5.292,2.083 false 4.708,1.667 5.208,1.667 false 3.823,1.615 3.948,2.51 3.948,2.51 4.104,2.51 false 6.156,2.417 6.5,2.417 false 5.802,3.594 6.073,3.594 false 5.75,0.771 6.031,1.125 0.281,0.354 18 false 5 5.042,2.865 5.323,3.219 0.281,0.354 18 false 8 5.365,1.938 5.646,2.292 0.281,0.354 18 false 9 5.479,1.458 6.031,1.813 0.552,0.354 18 false 11 4.458,2.354 5.01,2.708 0.552,0.354 18 false 12 5.521,0.552 5.833,0.75 0.313,0.198 10 false x 3 3.865,1.448 4.177,1.646 0.313,0.198 10 false x 3 4.573,1.781 4.885,1.979 0.313,0.198 10 false x 3 4.823,1.917 5.135,2.115 0.313,0.198 10 false x 3 6.313,3.188 6.625,3.385 0.313,0.198 10 false x 3 6.156,3.49 6.313,3.688 0.156,0.198 10 false ● 6.563,2.333 6.875,2.531 0.313,0.198 10 false *1 0.063,0.042 0.375,0.24 0.313,0.198 10 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

5 FRONT FENDER APRON TRIM PACKING D 53785B - - -
8 NO.2 ENGINE OIL LEVEL DIPSTICK GUIDE 12142 - - -
9 GLOW PLUG SCREW GROMMET 19850B - - -
11 NO.2 GLOW PLUG CONNECTOR 19872 (Click here) - -
12 GLOW PLUG ASSEMBLY 19850 (Click here) - -

*A BANK 2 - -
*1 ENGINE OIL LEVEL DIPSTICK - -

CAUTION / NOTICE / HINT

The necessary procedures(adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the glow plug assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



CAUTION:
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


PROCEDURE

Hide 1. WARM UP ENGINE

Z101186

CAUTION:

To protect the glow plug assembly from damage, before removing the glow plug assembly, make sure to warm up the engine.



Hide 2. PRECAUTION

Z101186

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

(Click here)



Hide 3.DISCONNECT DISCONNECT BATTERY NEGATIVE TERMINAL

Hide 53784 4.REMOVE FRONT FENDER APRON TRIM PACKING C

Hide 53785B 5.REMOVE FRONT FENDER APRON TRIM PACKING D

Hide 28101 6.REMOVE STARTER HOSE BRACKET SUB-ASSEMBLY

a.
A488331


Hide 17853B 7.REMOVE INTAKE MANIFOLD INSULATOR

a.
A488337


Hide 12142 8.REMOVE NO.2 ENGINE OIL LEVEL DIPSTICK GUIDE

a.
A488332


Hide 19850B 9.REMOVE GLOW PLUG SCREW GROMMET

a.
A488333


Hide 19871 10.REMOVE NO. 1 GLOW PLUG CONNECTOR

Z101186

CAUTION:

Make sure to wear protective gloves when performing work to avoid burns.



a.
A488335


Hide 19872 11.REMOVE NO. 2 GLOW PLUG CONNECTOR

Z101186

CAUTION:

Make sure to wear protective gloves when performing work to avoid burns.



a.
A488334


Hide 19850 12.REMOVE GLOW PLUG ASSEMBLY

Z101186

CAUTION:

Make sure to wear protective gloves when performing work to avoid burns.



a.
A488336N01
0.552,0.042 0.833,0.396 0.281,0.354 18 false i

i.

Using a 10 mm deep socket wrench, remove the 6 glow plug assemblies.