Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › from 2021.07
RM38G0E _58 Vehicle Interior _100610 THEFT DETERRENT / KEYLESS ENTRY _0467507 ENTRY AND START SYSTEM(for Start Function) U

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  TERMINALS OF ECU  


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


B574584N31
2,0.479 2.417,0.729 0.417,0.25 3.427,0.479 3.844,0.729 0.417,0.25 4.781,0.479 5.198,0.729 0.417,0.25 2.083,0.51 2.396,0.708 0.313,0.198 10 false I40 3.552,0.51 3.896,0.74 0.344,0.229 10 false I38 4.875,0.51 5.271,0.74 0.396,0.229 10 false I39

a.

Disconnect the I40 and I39 certification ECU (smart key ECU assembly) connectors.


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition Related Data List Item/DTC
I40-15 (NE) - Body ground Engine speed signal Always 10 kΩ or higher
Power Source Control

Engine Condition


I40-21 (STP1) - Body ground Stop light switch signal Brake pedal depressed → Brake pedal released 9 V or higher → 1 V or less
Power Source Control

Stop Light Switch


I39-6 (+B) - I39-29 (E) Power source Ignition switch off 11 to 14 V -
I39-14 (P) - I39-29 (E) P position signal Shift lever in P → Shift lever not in P 30 kΩ or higher → Below 200 Ω
Power Source Control

Shift P Signal


I40-22 (CUTB) - Body ground Dark current cut pin* Ignition switch off 11 to 14 V -
I39-29 (E) - Body ground GND Always Below 1 Ω -
I39-23 (SSW3) - Body ground SSW3 contact signal Engine switch pushed → Engine switch not pushed Below 15 Ω → 10 kΩ or higher
Power Source Control

Push Start Switch 3


I39-27 (SSW2) - Body ground SSW2 contact signal Engine switch pushed → Engine switch not pushed Below 15 Ω → 10 kΩ or higher
Power Source Control

Push Start Switch 2


I39-19 (SSW1) - Body ground SSW1 contact signal Engine switch pushed → Engine switch not pushed Below 15 Ω → 10 kΩ or higher
Power Source Control

Push Start Switch 1



*: In order to prevent the vehicle battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is installed in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode (example: the transmission of radio waves every 0.25 seconds, which forms the detection area, stops).



c.

Connect the I40 and I39 certification ECU (smart key ECU assembly) connectors.


d.

Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition Related Data List Item/DTC
I40-3 (STA) - I39-29 (E) When starting the engine, this monitors the voltage sent from terminal STAR to the starter relay to judge whether the engine is "being started". Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher*2 → 1.0 V or less -
I40-10 (STAR) - I39-29 (E)
Outputs voltage to the starter relay
·

Outputs voltage (12 V) to the starter relay when starting the engine. (Max. 30 sec. Turns off when an engine speed of 1000 rpm.)


HINT:

When Hi is selected, a start request signal (STAR) will not be output even though a start request signal (STSW) is input.


Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher*2 → 1.0 V or less -
I40-15 (NE) - Body ground Engine speed signal Idling (engine warmed up) Pulse generation
(See waveform 7)
Power Source Control

Engine Condition


I39-11 (SLP) - I39-29 (E) Steering lock position signal Steering locked → Steering unlocked 11 to 14 V → 1.5 V or less
Power Source Control

Steering Unlock Switch


I39-24 (SLR+) - I39-29 (E) Steering lock motor operation command signal
(Steering lock motor operation permission signal sent from the certification ECU (smart key ECU assembly))
When a door is opened, the steering lock motor will be operated if all of the following conditions are met:
·

The steering is unlocked.

·

The ignition switch is off.

·

The shift lever is in P.


Pulse generation
(See waveform 1)
-
I39-8 (LIN) - I39-29 (E) LIN communication line Ignition switch ON Pulse generation
Entry&Start

Steering Lock Start Condition


I39-14 (P) - I39-29 (E) P position signal Shift lever in P → Shift lever not in P 9 V or higher → 2.76 V or less
Power Source Control

Shift P Signal


I39-23 (SSW3) - I39-29 (E) SSW3 contact signal Engine switch not pushed → Engine switch pushed 9 V or higher → 1 V or less
Power Source Control

Push Start Switch 3


I39-27 (SSW2) - I39-29 (E) SSW2 contact signal Engine switch not pushed → Engine switch pushed 9 V or higher → 1 V or less
Power Source Control

Push Start Switch 2


I39-19 (SSW1) - I39-29 (E) SSW1 contact signal Engine switch not pushed → Engine switch pushed 9 V or higher → 1 V or less
Power Source Control

Push Start Switch 1


I39-21 (ACCD) - I39-29 (E) ACC signal Ignition switch off → Ignition switch ACC 1 V or less → 8.5 V or higher
Power Source Control

ACC Relay Monitor


I40-11(IGRD) - I39-29(E) IG signal Ignition switch off → Ignition switch ON 1 V or less → 9 V or higher
Power Source Control

IGR Relay Circuit (Outside) Monitor


I40-24(IGPD) - I39-29(E) IG signal Ignition switch off → Ignition switch ON 1 V or less → 9 V or higher
Power Source Control

IGP Relay Circuit (Outside) Monitor


I40-13 (SPD) - I39-29 (E) Vehicle speed signal Vehicle being driven at approx. 5 km/h (3 mph) Pulse generation
(See waveform 2)
Power Source Control

Vehicle Running Condition (Line)


I39-4 (CLG5) - I39-29 (E) Output to No. 1 indoor electrical key antenna assembly (front floor) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


Pulse generation
(See waveform 3)
-
I39-5 (CG5B) - I39-29 (E) Output to No. 1 indoor electrical key antenna assembly (front floor) (terminal on opposite side of component from CLG5 output terminal) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


Pulse generation
(See waveform 3)
-
I38-1 (CLG6) - I39-29 (E) Output to No. 3 indoor electrical key antenna assembly (rear floor) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


Pulse generation
(See waveform 4)
-
I38-2 (CG6B) - I39-29 (E) Output to No. 3 indoor electrical key antenna assembly (rear floor) (terminal on opposite side of component from CLG6 output terminal) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


Pulse generation
(See waveform 3)
-
I38-10 (CLG7) - I39-29 (E) Output to No. 3 indoor electrical key antenna assembly (inside luggage compartment) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


Pulse generation
(See waveform 3)
-
I38-9 (CG7B) - I39-29 (E) Output to No. 3 indoor electrical key antenna assembly (inside luggage compartment) (terminal on opposite side of component from CLG7 output terminal) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


Pulse generation
(See waveform 3)
-
I39-30 (AGND) - Body ground Transponder key amplifier ground Always Below 1 Ω -
I39-12 (ANT1) - I39-30 (AGND) Signal input / output from transponder key coil (transponder key coil built into engine switch) Ignition switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed Pulse generation
(See waveform 5)
Entry&Start

Encrypt Code Difference


I39-13 (ANT2) - I39-30 (AGND) Signal input / output from transponder key coil (transponder key coil built into engine switch) Ignition switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed Pulse generation
(See waveform 6)
I39-25 (IND) - I39-29 (E) Security indicator output Ignition switch off → ON Pulse generation → Below 2 V -
I38-20 (WCSW) - I39-29 (E)*1 Wireless charger system stop signal Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly inside vehicle

3.

Ignition switch off → ACC


Below 1 V → 4.5 to 6 V
(For 1 second after ignition switch to ACC)
-

HINT:
·

The waveform of the steering lock actuator motor stopped can be checked without performing any particular operation.

·

The waveform of the steering lock actuator motor operating can be checked if either of the following operations is performed:

-

To unlock the steering, bring the electrical key transmitter sub-assembly into the cabin and turn the ignition switch to ACC or ON.

-

To lock the steering, open a door with the ignition switch off and the shift lever in P.


·

*1: w/ Wireless Charger System

·

*2: While the engine is cranking, the battery voltage may drop to approximately 6 V.




e.

Using an oscilloscope, check the waveform of the ECU.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
C221561C09
1.521,1.583 2.375,1.74 0.854,0.156 2.281,0.479 2.729,0.635 0.448,0.156 0.24,0.417 1.635,0.615 1.396,0.198 2.01,1.75 2.198,2.042 2.198,2.042 2.323,2.042 false 0.948,0.406 2.927,0.25 2.927,0.25 2.521,0.479 false 2.927,1.594 3.313,1.792 0.385,0.198 10 GND 2.969,0.146 3.208,0.385 0.24,0.24 10 *a 2.375,1.979 2.552,2.146 0.177,0.167 10 *b
*a Steering lock motor not operating
*b Steering lock motor operating


Waveform 1

Measurement Condition
Item Content
Tester Connection I39-24 (SLR+) - I39-29 (E)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition When a door is opened, the steering lock motor will be operated if all of the following conditions are met:
·

The steering is unlocked.

·

The ignition switch is off.

·

The shift lever is in P.




ii.
B220145N21
2.875,1.177 3.229,1.344 0.354,0.167 10 false GND

Waveform 2

Measurement Condition
Item Content
Tester Connection I40-13 (SPD) - I39-29 (E)
Tool Setting 5 V/DIV., 20 ms./DIV.
Condition Vehicle being driven at approx. 5 km/h (3 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



iii.
B585746C02
0.354,1.167 0.813,1.365 0.458,0.198 10 false GND 1.365,1.896 1.823,2.094 0.458,0.198 10 false *a 2.469,1.896 2.927,2.094 0.458,0.198 10 false *b
*a For 30 seconds after any door closed
*b After 30 seconds or more have elapsed since any door closed


Waveform 3

Measurement Condition
Item Content
Tester Connection I39-4 (CLG5) - I39-29 (E)
I39-5 (CG5B) - I39-29 (E)
I38-2 (CG6B) - I39-29 (E)
I38-10 (CLG7) - I39-29 (E)
I38-9 (CG7B) - I39-29 (E)
Tool Setting 5 V/DIV., 500 ms./DIV.
Condition Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door




iv.
B585747C06
0.323,1.177 0.781,1.375 0.458,0.198 10 false GND 1.344,1.885 1.802,2.083 0.458,0.198 10 false *a 2.469,1.885 2.927,2.083 0.458,0.198 10 false *b
*a For 30 seconds after any door closed
*b After 30 seconds or more have elapsed since any door closed


Waveform 4

Measurement Condition
Item Content
Tester Connection I38-1 (CLG6) - I39-29 (E)
Tool Setting 5 V/DIV., 500 ms./DIV.
Condition Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door




v.
B585748N08
0.323,0.99 0.781,1.188 0.458,0.198 10 false GND

Waveform 5

Measurement Condition
Item Content
Tester Connection I39-12 (ANT1) - I39-30 (AGND)
Tool Setting 5 V/DIV., 200 ms/DIV.
Condition Ignition switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed


vi.
B585749N08
0.333,0.979 0.792,1.177 0.458,0.198 10 false GND

Waveform 6

Measurement Condition
Item Content
Tester Connection I39-13 (ANT2) - I39-30 (AGND)
Tool Setting 20 V/DIV., 200 ms./DIV.
Condition Ignition switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed


vii.
C222647N14
2.969,1.75 3.375,1.938 0.406,0.188 10 GND

Waveform 7

Measurement Condition
Item Content
Tester Connection I40-15 (NE) - Body ground
Tool Setting 2 V/DIV., 2 ms./DIV.
Condition Idling (engine warmed up)

HINT:

The wavelength becomes shorter as the engine speed increases.





CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)


C396298N14
1.75,0.792 2.146,1.063 0.396,0.271 1.865,0.844 2.323,1.042 0.458,0.198 10 false I49

a.

Disconnect the I49 steering lock ECU (steering lock actuator with ECU assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition Related Data List Item/DTC
I49-1 (GND) - Body ground Ground Always Below 1 Ω -
I49-7 (B) - Body ground Constant power supply Ignition switch off 11 to 14 V -


c.

Connect the I49 steering lock ECU (steering lock actuator with ECU assembly) connector.


d.

Measure the voltage, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition Related Data List Item/DTC
I49-3 (IGE) - I49-1 (GND) Steering lock motor operation permission signal (motor operation permission signal supplied by certification ECU (smart key ECU assembly)) Steering lock motor operating when all conditions met, and then door opened:
·

Shift lever in P

·

Steering unlocked

·

Ignition switch turned off


Pulse generation
(See waveform 1)
Entry&Start
·

Power Supply Short History

·

Unlock Request Receive

·

Steering Lock Request Receive


I49-4 (SLP) - I49-1 (GND) Steering lock bar position signal (signal output from steering unlock sensor) Steering locked → unlocked 11 to 14 V → Below 1.5 V
Entry&Start

Sensor Malfunction History


I49-5 (LIN) - I49-1 (GND) LIN communication line Ignition switch ON Pulse generation
Entry&Start

Steering Lock Start Condition


I49-6 (IG2) - I49-1 (GND) Steering lock motor operation permission signal (motor operation permission signal supplied by certification ECU (smart key ECU assembly)) Ignition switch off → ON Below 1 V → 11 to 14 V -

HINT:
·

There is 1 motor and 2 sensors built into the steering lock actuator with ECU assembly.

·

When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

-

To unlock the steering, carry the key and turn the ignition switch to ACC or ON.

-

To lock the steering, turn the ignition switch off with the shift lever in P, and then open a door.





e.
C221561C69
1.542,1.583 2.396,1.74 0.854,0.156 2.271,0.479 2.719,0.635 0.448,0.156 0.24,0.427 1.635,0.625 1.396,0.198 0.896,0.427 2.75,0.25 2.75,0.25 2.938,0.25 false 2.75,0.25 2.5,0.469 false 1.969,1.74 2.094,2.042 2.094,2.042 2.177,2.042 false 2.927,1.604 3.313,1.802 0.385,0.198 10 false GND 2.99,0.198 3.24,0.417 0.25,0.219 10 false *a 2.229,1.969 2.479,2.135 0.25,0.167 10 false *b
*a Steering lock motor not operating
*b Steering lock motor operating


Using an oscilloscope, check the waveform of the ECU.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 1

Measurement Condition
Item Content
Tester Connection I49-3 (IGE) - I49-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Steering lock motor operating when all conditions met, and then door opened:
·

Shift lever in P

·

Steering unlocked

·

Ignition switch turned off





CHECK ID CODE BOX (IMMOBILISER CODE ECU)


B510664N11
3.396,0.167 3.771,0.448 0.375,0.281 3.5,0.219 3.958,0.417 0.458,0.198 10 false I66

a.

Disconnect the I66 ID code box (immobiliser code ECU) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition Related Data List Item
I66-1 (+B) - Body ground Power source Ignition switch off 11 to 14 V -
I66-5 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the I66 ID code box (immobiliser code ECU) connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition Related Data List Item
I66-3 (EFII) - I66-5 (GND) EFI communication input
(Signal input from ECM to ID code box (immobiliser code ECU))
Ignition switch off 11 to 14 V Entry&Start
·

EFI Code Receive

·

Start Request


I66-3 (EFII) - I66-5 (GND) EFI communication input
(Signal input from ECM to ID code box (immobiliser code ECU))
Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to battery Pulse generation
(See waveform 1)
I66-4 (EFIO) - I66-5 (GND) EFI communication output
(Signal output from ID code box (immobiliser code ECU) to ECM)
Ignition switch off Below 1 V
I66-4 (EFIO) - I66-5 (GND) EFI communication output
(Signal output from ID code box (immobiliser code ECU) to ECM)
Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to battery Pulse generation
(See waveform 2)
I66-2 (LIN1) - I66-5 (GND) LIN communication line Ignition switch ON Pulse generation Entry&Start
·

Steering Lock Start Cond




e.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms. *b Approximately 270 ms.


Item Content
Tester Connection I66-3 (EFII) - I66-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to battery


ii.

Waveform 2

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms. *b Approximately 270 ms.


Item Content
Tester Connection I66-4 (EFIO) - I66-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to battery




CHECK ECM (for 1GR-FE)


C458640N01
2.229,0.281 2.615,0.542 0.385,0.26 5.427,0.281 5.813,0.542 0.385,0.26 2.302,0.333 2.615,0.542 0.313,0.208 10 false C92 5.542,0.333 5.854,0.542 0.313,0.208 10 false B2

a.

Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition Related Data List Item/DTC
B2-1 (BATT) - C92-81 (E1) +B power supply Always 11 to 14 V -
C92-81 (E1) - Body ground Ground Always Below 1 Ω -
B2-48 (IMO) - C92-81 (E1) EFI communication input
(Signal input from ECM to ID code box (immobiliser code ECU))
Ignition switch off 11 to 14 V
Entry&Start
·

EFI Code Receive

·

Engine Start Request


B2-48 (IMO) - C92-81 (E1) EFI communication input
(Signal input from ECM to ID code box (immobiliser code ECU))
Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to battery Pulse generation
(See waveform 1)
B2-46 (IMI) - C92-81 (E1) EFI communication input
(Signal output from ID code box (immobiliser code ECU) to ECM)
Ignition switch off 1 V or less
B2-46 (IMI) - C92-81 (E1) EFI communication input
(Signal output from ID code box (immobiliser code ECU) to ECM)
Ignition switch turned to ON using registered electrical key transmitter sub-assembly Pulse generation
(See waveform 2)
B2-41 (NEO) - C92-81 (E1) Engine speed signal Idling (engine warmed up) Pulse generation
(See waveform 3)
Power Source Control

Engine Condition


B2-16 (STA) - C92-81 (E1) When starting the engine, this monitors the voltage sent from terminal STAR to the starter relay to judge whether the engine is "being started". Engine is cranking 6 V or higher -


b.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C22
0.896,1.24 1.354,1.438 0.458,0.198 10 false GND 2.719,1.354 3.177,1.552 0.458,0.198 10 false *a 2.906,1.354 3.365,1.552 0.458,0.198 10 false *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection B2-48 (IMO) - C92-81 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to battery


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection B2-46 (IMI) - C92-81 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Ignition switch turned to ON using registered electrical key transmitter sub-assembly


iii.
A431371E02
2.833,0.938 3.292,1.135 0.458,0.198 10 false GND

Waveform 3

Measurement Condition
Item Content
Tester Connection B2-41 (NEO) - C92-81 (E1)
Tool Setting 5 V/DI., 20 ms./DIV.
Condition Idling (engine warmed up)

HINT:

The wavelength becomes shorter as the engine speed increases.





CHECK ECM (for V35A-FTS)


B460712E28
5.49,0.917 5.823,1.156 0.333,0.24 2.01,0.917 2.344,1.156 0.333,0.24 3.885,0.927 4.219,1.167 0.333,0.24 5.583,0.969 6.042,1.167 0.458,0.198 10 false B1 2.073,0.969 2.531,1.167 0.458,0.198 10 false C37 3.938,0.979 4.396,1.177 0.458,0.198 10 false C38

a.

Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition Related Data List Item/DTC
B1-1 (BATT) - B1-9 (E1) +B power supply Always 11 to 14 V -
B1-9 (E1) - Body ground Ground Always Below 1 Ω -
B1-23 (IMO) - B1-9 (E1) EFI communication input
(Signal input from ECM to ID code box (immobiliser code ECU))
Ignition switch off 11 to 14 V
Entry&Start
·

EFI Code Receive

·

Engine Start Request


B1-23 (IMO) - B1-9 (E1) EFI communication input
(Signal input from ECM to ID code box (immobiliser code ECU))
Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to battery Pulse generation
(See waveform 1)
B1-24 (IMI) - B1-9 (E1) EFI communication input
(Signal output from ID code box (immobiliser code ECU) to ECM)
Ignition switch off 1 V or less
B1-24 (IMI) - B1-9 (E1) EFI communication input
(Signal output from ID code box (immobiliser code ECU) to ECM)
Ignition switch turned to ON using registered electrical key transmitter sub-assembly Pulse generation
(See waveform 2)
B1-31 (NEO) - B1-9 (E1) Engine speed signal Idling (engine warmed up) Pulse generation
(See waveform 3)
Power Source Control

Engine Condition


B1-34 (STA) - B1-9 (E1) When starting the engine, this monitors the voltage sent from terminal STAR to the starter relay to judge whether the engine is "being started". Engine is cranking 6 V or higher -


b.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C22
0.896,1.24 1.354,1.438 0.458,0.198 10 false GND 2.719,1.354 3.177,1.552 0.458,0.198 10 false *a 2.906,1.354 3.365,1.552 0.458,0.198 10 false *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection B1-23 (IMO) - B1-9 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to battery


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection B1-24 (IMI) - B1-9 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Ignition switch turned to ON using registered electrical key transmitter sub-assembly


iii.
A431371E02
2.833,0.938 3.292,1.135 0.458,0.198 10 false GND

Waveform 3

Measurement Condition
Item Content
Tester Connection B1-31 (NEO) - B1-9 (E1)
Tool Setting 5 V/DI., 20 ms./DIV.
Condition Idling (engine warmed up)

HINT:

The wavelength becomes shorter as the engine speed increases.





CHECK ECM (for F33A-FTV)


B460712E29
2.104,0.781 2.552,1.021 0.448,0.24 3.813,0.792 4.26,1.031 0.448,0.24 5.344,0.781 5.802,1.021 0.458,0.24 2.167,0.823 2.781,1.021 0.615,0.198 10 false C138 3.875,0.844 4.49,1.042 0.615,0.198 10 false C139 5.448,0.823 6.063,1.021 0.615,0.198 10 false B70

a.

Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition Related Data List Item/DTC
B70-1 (BATT) - B70-10 (E1) +B power supply Always 11 to 14 V -
B70-10 (E1) - Body ground Ground Always Below 1 Ω -
B70-24 (IMO) - B70-10 (E1) EFI communication input
(Signal input from ECM to ID code box (immobiliser code ECU))
Ignition switch off 11 to 14 V
Entry&Start
·

EFI Code Receive

·

Engine Start Request


B70-24 (IMO) - B70-10 (E1) EFI communication input
(Signal input from ECM to ID code box (immobiliser code ECU))
Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to battery Pulse generation
(See waveform 1)
B70-23 (IMI) - B70-10 (E1) EFI communication input
(Signal output from ID code box (immobiliser code ECU) to ECM)
Ignition switch off 1 V or less
B70-23 (IMI) - B70-10 (E1) EFI communication input
(Signal output from ID code box (immobiliser code ECU) to ECM)
Ignition switch turned to ON using registered electrical key transmitter sub-assembly Pulse generation
(See waveform 2)
B70-31 (NEO) - B70-10 (E1) Engine speed signal Idling (engine warmed up) Pulse generation
(See waveform 3)
Power Source Control

Engine Condition


B70-25 (STA) - B70-10 (E1) When starting the engine, this monitors the voltage sent from terminal STAR to the starter relay to judge whether the engine is "being started". Engine is cranking 6 V or higher -


b.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C22
0.896,1.24 1.354,1.438 0.458,0.198 10 false GND 2.719,1.354 3.177,1.552 0.458,0.198 10 false *a 2.906,1.354 3.365,1.552 0.458,0.198 10 false *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection B70-24 (IMO) - B70-10 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to battery


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection B70-23 (IMI) - B70-10 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Ignition switch turned to ON using registered electrical key transmitter sub-assembly


iii.
A431371E02
2.833,0.938 3.292,1.135 0.458,0.198 10 false GND

Waveform 3

Measurement Condition
Item Content
Tester Connection B70-31 (NEO) - B70-10 (E1)
Tool Setting 5 V/DI., 20 ms./DIV.
Condition Idling (engine warmed up)

HINT:

The wavelength becomes shorter as the engine speed increases.





CHECK ENGINE SWITCH


B516200N15
3.385,0.208 3.781,0.458 0.396,0.25 3.469,0.24 3.927,0.438 0.458,0.198 10 false I75

a.

Disconnect the I75 engine switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition Related Data List Item/DTC
I75-3 (GND) - Body ground Transponder key amplifier ground Always Below 1 Ω -


c.

Connect the I75 engine switch connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition Related Data List Item/DTC
I75-1 (ANT1) - I75-3 (GND) Signal input / output from transponder key coil (transponder key coil built into engine switch) Ignition switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed Pulse generation
(See waveform 1)
Entry&Start

Encrypt Code Difference

HINT:

If immobiliser key code verification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above



I75-7 (ANT2) - I75-3 (GND) Signal input / output from transponder key coil (transponder key coil built into engine switch) Ignition switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed Pulse generation
(See waveform 2)
I75-11 (SS3) - I75-3 (GND) SS3 contact signal
HINT:

Backup for SS1. Behaves the same way as SS1.


Engine switch not pushed → Engine switch pushed 9 V or higher → Below 1 V
Power Source Control

Start Switch 3


I75-6 (SS2) - I75-3 (GND) SS2 contact signal
HINT:

Backup for SS1. Behaves the same way as SS1.


Engine switch not pushed → Engine switch pushed 9 V or higher → Below 1 V
Power Source Control

Start Switch 2


I75-12 (SS1) - I75-3 (GND) SS1 contact signal Engine switch not pushed → Engine switch pushed 9 V or higher → Below 1 V
Power Source Control

Start Switch 1




e.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B585748N05
0.354,0.969 0.813,1.167 0.458,0.198 10 false GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection I75-1 (ANT1) - I75-3 (GND)
Tool Setting 2 V/DIV., 20 ms/DIV.
Condition Ignition switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed


ii.
B585749N05
0.354,0.979 0.813,1.177 0.458,0.198 10 false GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection I75-7 (ANT2) - I75-3 (GND)
Tool Setting 20 V/DIV., 200 ms./DIV.
Condition Ignition switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed