Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function)
RM38G0E _58 Vehicle Interior _100610 THEFT DETERRENT / KEYLESS ENTRY _0467506 ENTRY AND START SYSTEM(for Entry Function) U

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  TERMINALS OF ECU  


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


B574584N28
3.375,0.406 3.792,0.656 0.417,0.25 4.802,0.406 5.219,0.656 0.417,0.25 1.969,0.417 2.385,0.667 0.417,0.25 4.917,0.448 5.229,0.646 0.313,0.198 10 false I39 3.469,0.448 3.781,0.646 0.313,0.198 10 false I38 2.073,0.458 2.385,0.656 0.313,0.198 10 false I40

a.

Disconnect the I40 and I39 certification ECU (smart key ECU assembly) connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Tester Connection Terminal Description Condition Specified Condition Related Data List Item
I39-29 (E) - Body ground Ground Always Below 1 Ω -
I39-6 (+B) - I39-29 (E) Power supply Always 11 to 14 V -
I40-22 (CUTB) - I39-29 (E) Dark current cut pin* Always 11 to 14 V -

*: In order to prevent the vehicle battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is installed in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode (example: the transmission of radio waves every 0.25 seconds, which forms the detection area, stops).



c.

Reconnect the I40 and I39 certification ECU (smart key ECU assembly) connectors.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Terminal Description Condition Specified Condition Related Data List Item
I40-24 (IGPD) - I39-29 (E) IG power supply Ignition switch off → ON Below 1 V → 9 V or higher
Power source control

IGP Relay Circuit (Outside) Monitor


I40-11 (IGRD) - I39-29 (E) IG power supply Ignition switch off → ON Below 1 V → 9 V or higher
Power source control

IGR Relay Circuit (Outside) Monitor


I39-21 (ACCD) - I39-29 (E) ACC power supply Ignition switch off → ACC Below 1 V → 8.5 V or higher
Power source control

ACC Relay Monitor


I39-16 (CLG1) - I39-29 (E) Output to driver door electrical key antenna
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*1)


Pulse generation
(See waveform 1)
-
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)


Pulse generation
(See waveform 2)
-
I39-16 (CLG1) - I39-29 (E) Input to driver door lock sensor
(front door outside handle assembly (for driver door) lock sensor on signal is sent to the certification ECU (smart key ECU assembly))
Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)

5.

Driver door lock sensor not touched → touched


Pulse generation
(See waveform 3)
Entry&Start

Driver Side Lock Sensor


I39-16 (CLG1) - I39-29 (E) Input to driver door unlock sensor
(when system is in unlock standby mode and unlock sensor is touched, door electrical key antenna sends unlock sensor input signal (sensing) to certification ECU (smart key ECU assembly))
Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Driver door unlock sensor not touched → touched


Pulse generation
(See waveform 4)
Entry&Start

Driver Side Unlock Sensor


I39-15 (CG1B) - I39-29 (E) Output to driver door electrical key antenna (terminal on opposite side of component from CLG1 output terminal) Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*1)


Pulse generation
(See waveform 5)
-
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)


Pulse generation
(See waveform 6)
-
I39-10 (CLG2) - I39-29 (E) Output to front passenger door electrical key antenna
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*1)


Pulse generation
(See waveform 1)
-
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)


Pulse generation
(See waveform 2)
-
I39-10 (CLG2) - I39-29 (E) Input to front passenger door lock sensor
(front door outside handle assembly (for front passenger door) lock sensor on signal is sent to the certification ECU (smart key ECU assembly))
Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)

5.

Front passenger door lock sensor not touched → touched


Pulse generation
(See waveform 3)
Entry&Start

Passenger Side Lock Sensor


I39-10 (CLG2) - I39-29 (E) Input to front passenger door unlock sensor
(when system is in unlock standby mode and unlock sensor is touched, door electrical key antenna sends unlock sensor input signal (sensing) to certification ECU (smart key ECU assembly))
Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Front passenger door unlock sensor not touched → touched


Pulse generation
(See waveform 4)
Entry&Start

Passenger Side Unlock Sensor


I39-9 (CG2B) - I39-29 (E) Output to front passenger door electrical key antenna (terminal on opposite side of component from CLG2 output terminal) Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*1)


Pulse generation
(See waveform 5)
-
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)


Pulse generation
(See waveform 6)
-
I38-27 (CLG3) - I39-29 (E)*2 Output to rear door electrical key antenna (for driver side)
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*1)


Pulse generation
(See waveform 1)
-
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)


Pulse generation
(See waveform 2)
-
I38-27 (CLG3) - I39-29 (E)*2 Input to rear door lock sensor (for driver side)
(rear door outside handle assembly (for driver side) lock sensor on signal is sent to the certification ECU (smart key ECU assembly))
Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)

5.

Rear door (for driver side) lock sensor not touched → touched


Pulse generation
(See waveform 3)
Entry&Start

Rear Driver Side Lock Sensor


I38-27 (CLG3) - I39-29 (E)*2 Input to rear door unlock sensor (for driver side)
(when system is in unlock standby mode and unlock sensor is touched, door electrical key antenna sends unlock sensor input signal (sensing) to certification ECU (smart key ECU assembly))
Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Rear door (for driver side) unlock sensor not touched → touched


Pulse generation
(See waveform 4)
Entry&Start

Rear Driver Side Unlock Sensor


I38-26 (CG3B) - I39-29 (E)*2 Output to rear door (for driver side) electrical key antenna (terminal on opposite side of component from CLG3 output terminal) Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*1)


Pulse generation
(See waveform 5)
-
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)


Pulse generation
(See waveform 6)
-
I38-14 (CLG4) - I39-29 (E)*2 Output to rear door electrical key antenna (for front passenger side)
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*1)


Pulse generation
(See waveform 1)
-
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)


Pulse generation
(See waveform 2)
-
I38-14 (CLG4) - I39-29 (E)*2 Input to rear door lock sensor (for front passenger side)
(rear door outside handle assembly (for front passenger side) lock sensor on signal is sent to the certification ECU (smart key ECU assembly))
Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)

5.

Rear door (for front passenger side) lock sensor not touched → touched


Pulse generation
(See waveform 3)
Entry&Start

Rear Passenger Side lock Sensor


I38-14 (CLG4) - I39-29 (E)*2 Input to rear door unlock sensor (for front passenger side)
(when system is in unlock standby mode and unlock sensor is touched, door electrical key antenna sends unlock sensor input signal (sensing) to certification ECU (smart key ECU assembly))
Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Rear door (for front passenger side) unlock sensor not touched → touched


Pulse generation
(See waveform 4)
Entry&Start

Rear Passenger Side Unlock Sensor


I38-13 (CG4B) - I39-29 (E)*2 Output to rear door (for front passenger side) electrical key antenna (terminal on opposite side of component from CLG4 output terminal) Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*1)


Pulse generation
(See waveform 5)
-
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)


Pulse generation
(See waveform 6)
-
I38-4 (CLG8) - I39-29 (E) Output to electrical key antenna (outside luggage compartment) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

License plate light assembly with back door opener switch off → on


Pulse generation
(See waveform 7)
-
I38-3 (CG8B) - I39-29 (E) Output to electrical key antenna (outside luggage compartment) (terminal on opposite side of component from CLG8 output terminal) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

License plate light assembly with back door opener switch off → on


Pulse generation
(See waveform 8)
-
I38-16 (TSW5) - I39-29 (E) License plate light assembly with back door opener switch (open switch) signal input License plate light assembly with back door opener switch (open switch) off → on Pulse generation
(See waveform 9)
Entry&Start

Trunk Lid/Back Door Unlock Switch


I38-17 (TSW6) - I39-29 (E) License plate light assembly with back door opener switch (lock switch) signal input License plate light assembly with back door opener switch (lock switch) off → on Pulse generation
(See waveform 9)
Entry&Start

Trunk Lid/Back Door Lock Switch


I38-21 (RCO) - I39-29 (E) Output to electrical key and tire pressure warning ECU and receiver
(Power supply for electrical key and tire pressure warning ECU and receiver. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.)
Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

3.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation
(See waveform 10)
-
I38-11 (RDAM) - I39-29 (E) Electrical key and tire pressure warning ECU and receiver verifies data received from electrical key transmitter sub-assembly.
Electrical key and tire pressure warning ECU and receiver sends data from electrical key transmitter sub-assembly to certification ECU (smart key ECU assembly) (Electrical key and tire pressure warning ECU and receiver intermittently grounds 12 V signal from certification ECU (smart key ECU assembly)).
Proceed:
1.

Ignition switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation
(See waveform 11)
-
I38-12 (CSEL) - I39-29 (E) Communication channel switching circuit Procedure:
1.

Ignition switch off

2.

All doors closed


Below 1 V → Pulse generation -

*1: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK

*2: w/ Rear Door Entry Function



e.
B581648N03
0.365,1 0.823,1.198 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 1.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 1 (Reference)
Item Content
Tester Connection I39-16 (CLG1) - I39-29 (E)
I39-10 (CLG2) - I39-29 (E)
I38-27 (CLG3) - I39-29 (E)*1
I38-14 (CLG4) - I39-29 (E)*1
Tool Setting 5 V/DIV., 500 ms./DIV.
Condition Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*2)



*1: w/ Rear Door Entry Function

*2: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



f.
B581649N02
0.375,1.01 0.833,1.208 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 2.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 2 (Reference)
Item Content
Tester Connection I39-16 (CLG1) - I39-29 (E)
I39-10 (CLG2) - I39-29 (E)
I38-27 (CLG3) - I39-29 (E)*1
I38-14 (CLG4) - I39-29 (E)*1
Tool Setting 5 V/DIV., 500 ms./DIV.
Condition Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*2)



*1: w/ Rear Door Entry Function

*2: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



g.
B581650C02
0.354,0.99 0.813,1.188 0.458,0.198 10 false GND 0.948,1.875 1.406,2.073 0.458,0.198 10 false *a 1.688,1.979 2.01,2.135 0.323,0.156 10 false *b 2.406,1.875 2.865,2.073 0.458,0.198 10 false *a
*a Lock sensor not touched
*b Lock sensor touched


Using an oscilloscope, check waveform 3.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 3 (Reference)
Item Content
Tester Connection I39-16 (CLG1) - I39-29 (E)
Tool Setting 5 V/DIV., 100 ms./DIV.
Condition Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)

5.

Driver door lock sensor not touched → touched



Item Content
Tester Connection I39-10 (CLG2) - I39-29 (E)
Tool Setting 5 V/DIV., 100 ms./DIV.
Condition Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)

5.

Front passenger door lock sensor not touched → touched



w/ Rear Door Entry Function:
Item Content
Tester Connection I38-27(CLG3) - I39-29(E)
Tool Setting 5 V/DIV., 100 ms./DIV.
Condition Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)

5.

Rear door (for driver side) lock sensor not touched → touched



w/ Rear Door Entry Function:
Item Content
Tester Connection I38-14(CLG4) - I39-29(E)
Tool Setting 5 V/DIV., 100 ms./DIV.
Condition Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)

5.

Rear door (for front passenger side) lock sensor not touched → touched



*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



h.
B581651C02
0.344,1 0.802,1.198 0.458,0.198 10 false GND 0.688,1.885 1.146,2.083 0.458,0.198 10 false *a 1.938,1.875 2.396,2.073 0.458,0.198 10 false *a 1.313,1.969 1.75,2.167 0.438,0.198 10 false *b
*a Unlock sensor not touched
*b Unlock sensor touched


Using an oscilloscope, check waveform 4.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 4 (Reference)
Item Content
Tester Connection I39-16 (CLG1) - I39-29 (E)
Tool Setting 5 V/DIV., 100 ms./DIV.
Condition Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Driver door unlock sensor not touched → touched



Item Content
Tester Connection I39-10 (CLG2) - I39-29 (E)
Tool Setting 5 V/DIV., 100 ms./DIV.
Condition Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Front passenger door unlock sensor not touched → touched



Item Content
Tester Connection I38-27 (CLG3) - I39-29 (E)
Tool Setting 5 V/DIV., 100 ms./DIV.
Condition Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Rear door (for driver side) unlock sensor not touched → touched



Item Content
Tester Connection I38-14 (CLG4) - I39-29 (E)
Tool Setting 5 V/DIV., 100 ms./DIV.
Condition Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Rear door (for front passenger side) unlock sensor not touched → touched




i.
B581652N03
0.333,1.01 0.792,1.208 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 5.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 5 (Reference)
Item Content
Tester Connection I39-15 (CG1B) - I39-29 (E)
I39-9 (CG2B) - I39-29 (E)
I38-26 (CG3B) - I39-29 (E)*1
I38-13 (CG4B) - I39-29 (E)*1
Tool Setting 5 V/DIV., 500 ms./DIV.
Condition Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*2)



*1: w/ Rear Door Entry Function

*2: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



j.
B581653N03
0.333,1.01 0.792,1.208 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 6.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 6 (Reference)
Item Content
Tester Connection I39-15 (CG1B) - I39-29 (E)
I39-9 (CG2B) - I39-29 (E)
I38-26 (CG3B) - I39-29 (E)*1
I38-13 (CG4B) - I39-29 (E)*1
Tool Setting 5 V/DIV., 500 ms./DIV.
Condition Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*2)



*1: w/ Rear Door Entry Function

*2: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



k.
B581654N02
0.365,1.063 0.823,1.26 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 7.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 7 (Reference)
Item Content
Tester Connection I38-4 (CLG8) - I39-29 (E)
Tool Setting 5 V/DIV., 50 ms./DIV.
Condition Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

License plate light assembly with back door opener switch off → on




l.
B581655N04
0.198,1.01 0.656,1.208 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 8.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 8 (Reference)
Item Content
Tester Connection I38-3(CG8B) - I39-29(E)
Tool Setting 5 V/DIV., 50 ms./DIV.
Condition Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

License plate light assembly with back door opener switch off → on




m.
B547115C05
1.281,0.479 2.333,0.125 2.333,0.125 1.677,0.479 false 0.198,1.198 0.531,1.396 0.333,0.198 10 false GND 2.375,0.063 2.708,0.26 0.333,0.198 10 false *a 0.865,1.906 1.198,2.104 0.333,0.198 10 false *b 1.729,1.896 2.063,2.094 0.333,0.198 10 false *c
*a Checking for switch on signal at short intervals
*b Before license plate light assembly with back door opener switch pressed
*c After license plate light assembly with back door opener switch pressed


Using an oscilloscope, check waveform 9.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 9 (Reference)
Item Content
Tester Connection I38-16 (TSW5) - I39-29 (E)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition License plate light assembly with back door opener switch (open switch) off → on

Item Content
Tester Connection I38-17 (TSW6) - I39-29 (E)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition License plate light assembly with back door opener switch (lock switch) off → on


n.
B251178C12
0.198,1 0.531,1.198 0.333,0.198 10 GND 1.01,1.885 1.198,2.042 0.188,0.156 10 *a 2.021,1.885 2.208,2.042 0.188,0.156 10 *b
*a Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*b After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check waveform 10.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 10 (Reference)
Item Content
Tester Connection I38-21 (RCO) - I39-29 (E)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

3.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed




o.
B251177C12
0.208,1 0.542,1.198 0.333,0.198 10 GND 1.021,1.896 1.208,2.052 0.188,0.156 10 *a 2.188,1.906 2.375,2.063 0.188,0.156 10 *b
*a Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*b After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check waveform 11.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 11 (Reference)
Item Content
Tester Connection I38-11 (RDAM) - I39-29 (E)
Tool Setting 5 V/DIV., 500 ms./DIV.
Condition Procedure:
1.

Ignition switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed





CHECK POWER DISTRIBUTION BOX ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


E444785C14
3.438,7.698 3.833,8 0.396,0.302 5.438,3.26 5.854,3.5 0.417,0.24 1.333,3.25 1.75,3.49 0.417,0.24 1.417,4.51 1.833,4.75 0.417,0.24 1.083,6.094 1.5,6.333 0.417,0.24 3,6.083 3.417,6.323 0.417,0.24 3.833,4.5 4.25,4.74 0.417,0.24 6.25,6.083 6.667,6.323 0.417,0.24 4.25,6.094 4.667,6.333 0.417,0.24 5.688,4.5 6.104,4.74 0.417,0.24 5.25,6.094 5.667,6.333 0.417,0.24 3.417,3.25 3.833,3.49 0.417,0.24 1.917,0.698 1.917,0.479 1.917,0.479 2.083,0.479 true 0.719,1.167 1,1.167 true 1.927,1.25 2.167,1.25 true 1.927,1.552 2.167,1.552 true 0.75,1.958 0.99,1.958 true 0.76,2.229 1,2.229 true 0.75,2.469 1.229,2.469 true 0.719,1.667 1,1.667 true 6.167,1.208 6.448,1.208 true 6.167,1.771 6.448,1.771 true 6.167,2.167 6.448,2.167 true 1.927,1.875 2.167,1.875 true 1.25,0.5 1.25,0.281 1.25,0.281 1.417,0.281 true 4.5,0.583 4.5,0.365 4.5,0.365 4.667,0.365 true 6,0.531 6,0.313 6,0.313 6.167,0.313 true 3.927,1 4.083,1.198 0.156,0.198 10 false A 3.594,7.76 3.75,7.958 0.156,0.198 10 false A 0.521,1.583 0.833,1.781 0.313,0.198 10 false 5E 0.521,1.885 0.833,2.083 0.313,0.198 10 false 5K 2.208,1.167 2.667,1.365 0.458,0.198 10 false I1 2.208,1.469 2.667,1.667 0.458,0.198 10 false I2 0.552,2.156 1.052,2.385 0.5,0.229 10 false 5J 2.125,0.385 2.583,0.583 0.458,0.198 10 false *2 6.521,1.135 6.833,1.333 0.313,0.198 10 false 5C 6.521,1.688 6.833,1.885 0.313,0.198 10 false 5B 1.5,3.292 1.958,3.49 0.458,0.198 10 false I3 3.594,3.292 4.052,3.49 0.458,0.198 10 false I2 1.563,4.552 1.875,4.75 0.313,0.198 10 false 5C 3.979,4.552 4.292,4.75 0.313,0.198 10 false 5B 1.229,6.146 1.542,6.344 0.313,0.198 10 false 5F 3.135,6.125 3.448,6.323 0.313,0.198 10 false 5E 6.385,6.135 6.698,6.333 0.313,0.198 10 false 5H 4.385,6.135 4.74,6.292 0.354,0.156 10 false 5K 0.521,1.094 1.135,1.292 0.615,0.198 10 false 5F 0.521,2.396 1.021,2.625 0.5,0.229 10 false 5H 6.521,2.083 6.833,2.281 0.313,0.198 10 false 5A 5.823,4.542 6.135,4.74 0.313,0.198 10 false 5A 5.406,6.135 5.719,6.333 0.313,0.198 10 false 5J 2.208,1.802 2.667,2 0.458,0.198 10 false I3 5.604,3.302 6.063,3.5 0.458,0.198 10 false I1 1.458,0.219 1.917,0.417 0.458,0.198 10 false *1 4.708,0.302 5.167,0.5 0.458,0.198 10 false *1 6.219,0.25 6.677,0.448 0.458,0.198 10 false *1
*1 Power Distribution Box Assembly *2 Main Body ECU (Multiplex Network Body ECU)


a.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL

for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL


b.

Measure the voltage and resistance according to the value(s) in the table below.

Tester Connection Terminal Description Condition Specified Condition
A-13 (GND1) - Body ground Ground Always Below 1 Ω
A-26 (BECU) - Body ground Battery power supply (for CPU) Always 11 to 14 V


c.

Install the main body ECU (multiplex network body ECU) to the power distribution box assembly.

for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>INSTALLATION

for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>INSTALLATION


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Terminal Description Condition Specified Condition Related Data List Item
5E-7 (BZR) - Body ground Output Wireless door lock buzzer output Active Test Wireless Buzzer on Pulse generation
(frequency: 2 kHz, high voltage: 11 to 14 V, low voltage: below 1 V)
-
Active Test Wireless Buzzer off Below 1 V