Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › from 2021.07
RM38G0E _58 Vehicle Interior _100610 THEFT DETERRENT / KEYLESS ENTRY _0467507 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  P033562  Crankshaft Position Sensor "A" Signal Compare Failure  


DESCRIPTION

These DTCs are stored when the engine speed signal sent by the ECM via direct line and the engine speed signal sent via CAN communication do not match.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
P033562 Crankshaft Position Sensor "A" Signal Compare Failure The engine speed signal sent by the ECM via direct line and the engine speed signal sent via CAN communication do not match. (1-trip detection logic*)
for Gasoline:
·

SFI system

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


for Diesel:
·

ECD system

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


Power Source Control A
DTC Output Confirmation Operation:

Allow the engine to idle for 10 seconds or more, and then engine speed of 1000 rpm or more for 20 seconds or more.



*: Only detected while a malfunction is present and the ignition switch is ON.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
·

When a malfunction occurs and the vehicle speed signal sent via either direct line or CAN communication indicates no vehicle speed, there is no effect on vehicle behavior. (A malfunction is detected after the ignition switch is turned to ON.)

·

When a malfunction occurs and the vehicle speed signal sent via either direct line or CAN communication indicates that the vehicle is moving, the engine cannot be started. However, the engine can be started after the ignition switch has been turned off.


·

When a malfunction occurs and the vehicle speed signal sent via either direct line or CAN communication indicates no vehicle speed, there is no effect on vehicle behavior.

·

When the signal sent via either direct line or CAN communication is malfunctioning and indicates that the vehicle is moving:

If the following conditions are met, it can be determined that the malfunction is not in the CAN communication system but in the direct line (NE).
-

When the engine switch is pressed, the system controls the engine based on the starter OFF permission flag (perfect injection signal judgment) via CAN communication, causing the engine to stop cranking.

-

When the engine switch is pressed and held, the system controls the engine based on the engine speed signal via CAN communication, causing the engine to stop cranking.


If the following conditions are met, it can be determined that the malfunction is not in the direct line (NE) but in the CAN communication system.
-

When the engine switch is pressed, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking.

-

When the engine switch is pressed and held, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking.


If the following conditions are met, it can be determined that there is a malfunction in both the CAN communication system and the direct line (NE).
-

When the engine switch is pressed, the engine stops cranking after 6 seconds.

-

When the engine switch is pressed and held, the engine cranks for up to 30 seconds.




Related Data List and Active Test Items
DTC No. Data List and Active Test
P033562
Power Source Control
·

Engine Driving Condition (Line)

·

Engine Speed



WIRING DIAGRAM

B478908E70
0.708,1.583 2.031,1.75 1.323,0.167 10 false B2*1, B1*2, B70*3 1.135,1.781 1.688,2.073 0.552,0.292 10 false ECM 0.885,2.219 2.833,2.531 1.948,0.313 10 false : CAN Communication Line 1.51,0.76 2.063,1.052 0.552,0.292 10 false NEO 1.927,0.75 3.156,0.938 1.229,0.188 10 false 41*1, 31*2, 31*3 5.281,0.74 5.833,1.031 0.552,0.292 10 false 15 5.552,0.74 6.104,1.031 0.552,0.292 10 false NE 5.76,0.365 6.313,0.656 0.552,0.292 10 false +B 6.125,0.99 6.677,1.281 0.552,0.292 10 false IC 5.229,1.417 6.458,1.719 1.229,0.302 10 false I40 5.219,1.583 7.042,1.938 1.823,0.354 10 false Certification ECU (Smart Key ECU Assembly) 2.74,2.24 4.188,2.542 1.448,0.302 10 false *1: for 1GR-FE 3.844,2.229 5.292,2.531 1.448,0.302 10 false *2: for V35A-FTS 5.167,2.219 6.542,2.448 1.375,0.229 10 false *3: for F33A-FTV

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.READ VALUE USING GTS (ENGINE DRIVING CONDITION (LINE), ENGINE SPEED)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Driving Condition (Line) Engine state Stop or Driving Stop: Engine stopped
Driving: Engine running
-
Body Electrical > Power Source Control > Data List
Tester Display
Engine Driving Condition (Line)
50003 454 401
Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Speed Engine speed 0 to 16383.75 rpm Fluctuates in accordance with actual engine speed -
Body Electrical > Power Source Control > Data List
Tester Display
Engine Speed
50003 454 101
OK:

The GTS display changes correctly in response to the engine condition.


Result:
Result Proceed to
OK (for Gasoline) A
OK (for Diesel) B
NG C




A

B

C

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

Pre-procedure1

a.

Disconnect the I40 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the B2*1, B1*2, B70*3 ECM connector.

*1: for 1GR-FE

*2: for V35A-FTS

*3: for F33A-FTV


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE
Tester Connection Condition Specified Condition

Click Location & Routing(I40,B2)Location & Routing

Click Connector(I40)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

Click Connector(B2)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

I40-15 (NE) - B2-41 (NEO) Always Below 1 Ω
I40-15 (NE) or B2-41 (NEO) - Other terminals and body ground Always 10 kΩ or higher

for V35A-FTS
Tester Connection Condition Specified Condition

Click Location & Routing(I40,B1)Location & Routing

Click Connector(I40)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

Click Connector(B1)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

I40-15 (NE) - B1-31 (NEO) Always Below 1 Ω
I40-15 (NE) or B1-31 (NEO) - Other terminals and body ground Always 10 kΩ or higher

for F33A-FTV
Tester Connection Condition Specified Condition

Click Location & Routing(I40,B70)Location & Routing

Click Connector(I40)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

Click Connector(B70)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

I40-15 (NE) - B70-31 (NEO) Always Below 1 Ω
I40-15 (NE) or B70-31 (NEO) - Other terminals and body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

Pre-procedure1

a.

Connect the I40 certification ECU (smart key ECU assembly) connector.


b.

Connect the B2*1, B1*2, B70*3 ECM connector.

*1: for 1GR-FE

*2: for V35A-FTS

*3: for F33A-FTV


Procedure1

c.
B574625C51
1.354,0.052 1.719,0.24 0.365,0.188 2.146,1.938 1.844,1.938 1.844,1.938 1.313,0.823 true 0.156,0.063 0.469,0.219 0.313,0.156 10 false *a 1.406,0.063 1.719,0.219 0.313,0.156 10 false I40 2.208,1.854 2.646,2.042 0.438,0.188 10 false NE
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Using an oscilloscope, check the engine speed input signal waveform at the terminal of the certification ECU (smart key ECU assembly).

OK:
Tester Connection Condition Specified Condition

Click Location & Routing(I40)Location & Routing

Click Connector(I40)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

I40-15 (NE) - Body ground Engine stopped No pulse generation
I40-15 (NE) - Body ground Engine running Pulse generation


Result:
Result Proceed to
OK A
NG (for Gasoline) B
NG (for Diesel) C



Post-procedure1

d.

None



A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

C