| *1 | VANE PUMP FRONT HOUSING | *2 | VANE PUMP PLATE |
| *3 | VANE PUMP SHAFT | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
|
Power Steering Fluid |
|
MP Grease |
1.INSTALL VANE PUMP HOUSING OIL SEAL
Coat a new lip of the vane pump housing oil seal with power steering fluid.
Using SST and a press, press in the vane pump housing oil seal.
2.INSTALL VANE PUMP SHAFT BEARING
Using a brass bar and hammer, tap in a new vane pump shaft snap ring.
Be careful not to damage the vane pump shaft.
Using a press, press in the vane pump shaft into the vane pump shaft bearing.
Be careful not to damage the vane pump shaft bearing.
3.INSTALL VANE PUMP SHAFT WITH VANE PUMP SHAFT BEARING
Temporarily install the vane pump rear housing to the vane pump front housing.
Using SST and a press, press in the vane pump shaft with vane pump shaft bearing into the vane pump front housing.
Using a screwdriver, install a new vane pump housing snap ring into the vane pump front housing.
44316 4.INSTALL VANE PUMP GEAR
Using SST and a press, press in the vane pump gear to the vane pump shaft.
Remove the vane pump rear housing from the vane pump front housing.
5.INSTALL VANE PUMP FRONT SIDE PLATE
|
Power Steering Fluid |
|
Install in this Direction |
Coat a new O-ring with power steering fluid and install it into the vane pump front housing.
Coat a new O-ring with power steering fluid and install it onto the vane pump front side plate.
Align the notch of the vane pump front side plate with the notch of the vane pump front housing, and install the vane pump front side plate.
Make sure that the vane pump front side plate is installed facing in the correct direction.
6.INSTALL VANE PUMP CAM RING
| *a | Inscribed Mark | - | - |
Align the notch of the vane pump cam ring with the notch of the vane pump front side plate, and install the vane pump cam ring with the inscribed mark facing upward.
Make sure that the vane pump cam ring is installed facing in the correct direction.
7.INSTALL VANE PUMP ROTOR
| *a | Inscribed Mark | *b | Round End |
Install the vane pump rotor with the inscribed mark facing outward.
Coat the 10 vane pump plates with power steering fluid.
Install the 10 vane pump plates with the round end facing outward.
Make sure that the 10 vane pump plates are installed facing in the correct direction.
8.INSTALL VANE PUMP REAR HOUSING
| *a | Align | - | - |
Coat a new O-ring with power steering fluid and install it onto the vane pump rear housing.
Securely insert the O-ring into the groove of the vane pump rear housing.
Align the straight pin of the vane pump rear housing with the notches of the vane pump cam ring, vane pump front side plate and vane pump front housing.
Check that the O-ring has not come out of the groove and install the vane pump rear housing.
Install the vane pump rear housing with the 4 bolts.
9.INSPECT TOTAL PRELOAD
| *a | Service Bolt | - | - |
Check that the vane pump rotates smoothly without abnormal noise.
Temporarily install the service bolt.
| Item | Specified Condition |
|---|---|
| Thread Diameter | 10 mm (0.394 in.) |
| Thread Pitch | 1.25 mm (0.0492 in.) |
| Bolt Length | 50 mm (1.97 in.) |
Using a torque wrench, measure the pump rotating torque.
0.27 N*m (2.8 kgf*cm, 2.4 in.*lbf) or less
If the rotating torque is not as specified, check the vane pump housing oil seal.
44337 10.INSTALL POWER STEERING SUCTION PORT UNION