Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2021.07
RM38G0E _56 Audio / Visual / Telematics _100607 NAVIGATION / MULTI INFO DISPLAY _0467503 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Microphone Circuit  


DESCRIPTION

·

The radio receiver assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

·

Using this circuit, the radio receiver assembly sends power to the telephone microphone assembly, and the telephone microphone assembly sends microphone signals to the radio receiver assembly and navigation ECU assembly.


WIRING DIAGRAM

E377486E41
1.5,0.854 2.01,1.073 0.51,0.219 10 false SNS2 1.469,1.406 1.906,1.594 0.438,0.188 10 false MACC 1.469,1.958 1.958,2.177 0.49,0.219 10 false MCO+ 1.5,2.51 1.948,2.708 0.448,0.198 10 false MCO- 0.479,2.938 1.5,3.115 1.021,0.177 10 false d28*1, d30*2 0.479,3.115 1.885,3.49 1.406,0.375 10 false Telephone Microphone Assembly 2.042,0.76 2.552,0.979 0.51,0.219 10 false 3 2.042,1.281 2.552,1.5 0.51,0.219 10 false 1 2.052,1.875 2.563,2.094 0.51,0.219 10 false 2 2.052,2.438 2.563,2.656 0.51,0.219 10 false 4 5.615,0.667 6.125,0.885 0.51,0.219 10 false 25 5.604,0.875 5.875,1.073 0.271,0.198 10 false I12 5.615,1.24 6.125,1.458 0.51,0.219 10 false 23 5.615,1.792 6.125,2.01 0.51,0.219 10 false 21 5.604,2.365 6.115,2.583 0.51,0.219 10 false 22 5.604,2.917 6.115,3.135 0.51,0.219 10 false 24 5.948,0.844 6.458,1.063 0.51,0.219 10 false SNS2 5.958,1.406 6.469,1.625 0.51,0.219 10 false MACC 5.958,1.969 6.354,2.177 0.396,0.208 10 false MIN+ 5.958,2.531 6.344,2.729 0.385,0.198 10 false MIN- 5.958,3.083 6.417,3.271 0.458,0.188 10 false SGND 5.958,4.302 6.427,4.5 0.469,0.198 10 false MCO+ 5.948,5.427 6.375,5.594 0.427,0.167 10 false SGND 5.958,4.875 6.396,5.063 0.438,0.188 10 false MCO- 5.615,4.156 6.125,4.375 0.51,0.219 10 false 25 5.583,4.365 5.917,4.552 0.333,0.188 10 false I14 5.604,4.698 6.115,4.917 0.51,0.219 10 false 26 5.615,5.229 6.125,5.448 0.51,0.219 10 false 24 4.417,4.188 4.927,4.406 0.51,0.219 10 false 13 4.417,4.781 4.927,5 0.51,0.219 10 false 14 3.969,4.323 4.365,4.521 0.396,0.198 10 false MIC+ 3.99,4.865 4.385,5.063 0.396,0.198 10 false MIC- 3.406,5.792 3.917,6.01 0.51,0.219 10 false I21 3.417,5.979 4.917,6.208 1.5,0.229 10 false Navigation ECU 5.885,5.76 6.813,6.125 0.927,0.365 10 false Radio Receiver Assembly 5.594,4.906 5.896,5.094 0.302,0.188 10 false I14 5.594,5.448 5.927,5.615 0.333,0.167 10 false I14 5.604,1.448 5.917,1.635 0.313,0.188 10 false I12 5.594,2 5.896,2.188 0.302,0.188 10 false I12 5.594,2.563 5.906,2.76 0.313,0.198 10 false I12 5.583,3.125 5.885,3.292 0.302,0.167 10 false I12 3.625,2.844 3.865,3.031 0.24,0.188 10 false *3 0.271,6.281 1.448,6.625 1.177,0.344 10 false *3: Shielded 4.865,5.177 5.104,5.365 0.24,0.188 10 false *3 0.271,5.958 1.448,6.302 1.177,0.344 10 false *2: for RHD 0.302,5.615 1.479,5.958 1.177,0.344 10 false *1: for LHD 0.083,0.073 6.198,0.365 6.115,0.292 12 false w/o Telematics Transceiver or w/ Telematics System (for ERA-GLONASS):

E362092E80
0.448,2.698 0.719,2.906 0.271,0.208 10 false d30 1.51,0.625 2.125,0.823 0.615,0.198 10 false SNS2 1.469,1.177 2.083,1.375 0.615,0.198 10 false MACC 1.49,1.74 2.104,1.938 0.615,0.198 10 false MCO+ 1.5,2.302 2.115,2.5 0.615,0.198 10 false MCO- 3.427,1.198 4.042,1.396 0.615,0.198 10 false MCVD 3.427,1.75 4.042,1.948 0.615,0.198 10 false MCI+ 3.427,2.313 4.042,2.51 0.615,0.198 10 false MCI- 3.417,2.875 4.031,3.073 0.615,0.198 10 false SGND 3.896,1.198 4.51,1.396 0.615,0.198 10 false MCO+ 3.885,1.76 4.5,1.958 0.615,0.198 10 false MCO- 5.958,0.646 6.573,0.844 0.615,0.198 10 false SNS2 5.958,1.198 6.573,1.396 0.615,0.198 10 false MIN+ 5.948,1.76 6.563,1.958 0.615,0.198 10 false MIN- 5.948,2.323 6.563,2.521 0.615,0.198 10 false SGND 5.948,4.271 6.563,4.469 0.615,0.198 10 false MCO+ 5.948,4.813 6.563,5.01 0.615,0.198 10 false MCO- 5.948,5.365 6.563,5.563 0.615,0.198 10 false SGND 4,4.271 4.615,4.469 0.615,0.198 10 false MIC+ 4,4.802 4.615,5 0.615,0.198 10 false MIC- 3.25,3.198 3.75,3.417 0.5,0.219 10 false I55 3.448,5.688 3.948,5.906 0.5,0.219 10 false I21 5.594,5.354 6.052,5.552 0.458,0.198 10 false I14 5.615,0.99 5.927,1.188 0.313,0.198 10 false 21 5.615,1.552 5.927,1.75 0.313,0.198 10 false 22 5.615,2.115 5.927,2.313 0.313,0.198 10 false 24 5.615,0.438 5.927,0.635 0.313,0.198 10 false 25 4.375,1.104 4.688,1.302 0.313,0.198 10 false 16 4.385,1.635 4.698,1.833 0.313,0.198 10 false 32 3.198,1.094 3.51,1.292 0.313,0.198 10 false 5 3.198,1.656 3.51,1.854 0.313,0.198 10 false 6 3.208,2.219 3.521,2.417 0.313,0.198 10 false 7 3.146,2.781 3.458,2.979 0.313,0.198 10 false 23 1.99,0.542 2.302,0.74 0.313,0.198 10 false 3 1.99,1.094 2.302,1.292 0.313,0.198 10 false 1 1.99,1.646 2.302,1.844 0.313,0.198 10 false 2 2,2.208 2.313,2.406 0.313,0.198 10 false 4 4.396,4.177 4.708,4.375 0.313,0.198 10 false 13 4.396,4.729 4.708,4.927 0.313,0.198 10 false 14 5.615,4.063 5.927,4.26 0.313,0.198 10 false 25 5.615,4.615 5.927,4.813 0.313,0.198 10 false 26 5.625,5.156 5.938,5.354 0.313,0.198 10 false 24 5.594,4.813 6.052,5.01 0.458,0.198 10 false I14 5.594,4.25 6.052,4.448 0.458,0.198 10 false I14 5.594,0.625 6.052,0.823 0.458,0.198 10 false I12 3.427,5.844 4.479,6.063 1.052,0.219 10 false Navigation ECU 0.438,2.875 2.552,3.115 2.115,0.24 10 false Telephone Microphone Assembly 3.229,3.354 5.479,3.594 2.25,0.24 10 false Telephone Transceiver Assembly 5.854,5.656 6.833,6.063 0.979,0.406 10 false Radio Receiver Assembly 0.094,0.052 4.427,0.313 4.333,0.26 12 false w/ Telematics System (for Toyota Connected Services): 5.604,1.188 6.063,1.385 0.458,0.198 10 false I12 5.594,1.74 6.052,1.938 0.458,0.198 10 false I12 5.594,2.302 6.052,2.5 0.458,0.198 10 false I12 4.896,5.219 5.396,5.438 0.5,0.219 10 false * 4.896,2.281 5.396,2.5 0.5,0.219 10 false * 2.729,2.74 3.229,2.958 0.5,0.219 10 false *

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle type. Refer to Check Microphone (Input to navigation ECU) in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK


Result:
Result Proceed to
w/o Recording Function A
w/ Recording Function B



A

2.CHECK MICROPHONE AND VOICE RECOGNITION (INPUT TO NAVIGATION ECU)

B

4.CHECK MICROPHONE AND VOICE RECOGNITION (INPUT TO NAVIGATION ECU ASSEMBLY)
2.CHECK MICROPHONE AND VOICE RECOGNITION (INPUT TO NAVIGATION ECU)
a.
E277821

Enter the "Microphone Check" screen. Refer to Check Microphone (Input to navigation ECU) in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK


b.

When voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

HINT:

The microphone is active at all times when "Microphone Check" screen is displayed.


OK:

Microphone input level meter changes according to the input voice.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK MICROPHONE AND VOICE RECOGNITION (INPUT TO RADIO RECEIVER ASSEMBLY)
3.CHECK MICROPHONE AND VOICE RECOGNITION (INPUT TO RADIO RECEIVER ASSEMBLY)
a.
E277821

Enter the "Microphone Check" screen. Refer to Check Microphone (Input to radio receiver assembly) in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK


b.

When voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

HINT:

The microphone is active at all times when "Microphone Check" screen is displayed.


OK:

Microphone input level meter changes according to the input voice.



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (RADIO RECEIVER ASSEMBLY - NAVIGATION ECU)

NG

8.CHECK VEHICLE TYPE
4.CHECK MICROPHONE AND VOICE RECOGNITION (INPUT TO NAVIGATION ECU ASSEMBLY)
a.
E268457

Enter the "Microphone Check" screen. Refer to Check Microphone (Input to navigation ECU assembly) in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK


b.

When voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check results are normal.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

5.CHECK MICROPHONE AND VOICE RECOGNITION (INPUT TO RADIO RECEIVER ASSEMBLY)
5.CHECK MICROPHONE AND VOICE RECOGNITION (INPUT TO RADIO RECEIVER ASSEMBLY)
a.
E268457

Enter the "Microphone Check" screen. Refer to Check Microphone (Input to radio receiver assembly) in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK


b.

When voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check results are normal.



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NAVIGATION ECU ASSEMBLY)

NG

8.CHECK VEHICLE TYPE
6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NAVIGATION ECU ASSEMBLY)
a.

Disconnect the I14 radio receiver assembly connector.


b.

Disconnect the I21 navigation ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I14,I21)Location & Routing

Click Connector(I14)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio Receiver Assembly

Click Connector(I21)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Navigation ECU Assembly

I14-25 (MCO+) - I21-13 (MIC+) Always Below 1 Ω
I14-26 (MCO-) - I21-14 (MIC-) Always Below 1 Ω
I14-25 (MCO+) or I21-13 (MIC+) - Body ground Always 10 kΩ or higher
I14-26 (MCO-) or I21-14 (MIC-) - Body ground Always 10 kΩ or higher
I14-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK RADIO RECEIVER ASSEMBLY (OUTPUT TO NAVIGATION ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK RADIO RECEIVER ASSEMBLY (OUTPUT TO NAVIGATION ECU ASSEMBLY)
a.

Disconnect the I21 navigation ECU assembly connector.


b.
E368005C70
1.5,0.427 1.917,0.677 0.417,0.25 1.75,2.083 1.292,1.469 true 0.833,2.083 1.188,1.469 true 2.813,3.427 3.208,3.656 0.396,0.229 10 false GND 0.656,2.115 1.052,2.344 0.396,0.229 10 false MIC+ 0.167,0.135 0.563,0.365 0.396,0.229 10 false *a 1.583,0.469 1.979,0.698 0.396,0.229 10 false I21 1.646,2.115 2.042,2.344 0.396,0.229 10 false MIC-
*a Front view of wire harness connector
(to Navigation ECU Assembly)


Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal I21-13 (MIC+) - I21-14 (MIC-)
Tool setting 50 mV/DIV., 500 ms./DIV.
Vehicle condition
1.

Ignition switch ACC.

2.

Sound is input to the telephone microphone assembly when the user is closer than 125 mm (4.92 in.) from the telephone microphone assembly sound holes in the microphone case.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

8.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
w/ Telematics System (for Toyota Connected Services) A
w/o Telematics Transceiver or w/ Telematics System (for ERA-GLONASS) B



A

9.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)

B

15.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)
9.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)
a.

Disconnect the I12 radio receiver assembly connector.


b.

Disconnect the d30 telephone microphone assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I12,d30)Location & Routing

Click Connector(I12)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio Receiver Assembly

Click Connector(d30)Body>No. 1 Roof Wire>Telephone Microphone Assembly RH

I12-25 (SNS2) - d30-3 (SNS2) Always Below 1 Ω
I12-25 (SNS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEPHONE TRANSCEIVER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEPHONE TRANSCEIVER ASSEMBLY)
a.

Disconnect the I12 radio receiver assembly connector.


b.

Disconnect the I55 telephone transceiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I12,I55)Location & Routing

Click Connector(I12)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio Receiver Assembly

Click Connector(I55)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Telematics Transceiver Assembly

I12-21 (MIN+) - I55-16 (MCO+) Always Below 1 Ω
I12-22 (MIN-) - I55-32 (MCO-) Always Below 1 Ω
I12-21 (MIN+) - Body ground Always 10 kΩ or higher
I12-22 (MIN-) - Body ground Always 10 kΩ or higher
I12-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)
a.

Disconnect the I55 telephone transceiver assembly connector.


b.

Disconnect the d30 telephone microphone assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I55,d30)Location & Routing

Click Connector(I55)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Telematics Transceiver Assembly

Click Connector(d30)Body>No. 1 Roof Wire>Telephone Microphone Assembly RH

I55-5 (MCVD) - d30-1 (MACC) Always Below 1 Ω
I55-6 (MCI+) - d30-2 (MCO+) Always Below 1 Ω
I55-7 (MCI-) - d30-4 (MCO-) Always Below 1 Ω
I55-5 (MCVD) - Body ground Always 10 kΩ or higher
I55-6 (MCI+) - Body ground Always 10 kΩ or higher
I55-7 (MCI-) - Body ground Always 10 kΩ or higher
I55-23 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK TELEPHONE TRANSCEIVER ASSEMBLY
a.
E427105C81
1.521,0.615 1.948,0.865 0.427,0.25 2.24,1.719 2.458,0.542 2.458,0.542 2.667,0.542 true 2.406,1.708 2.563,0.948 2.563,0.948 2.74,0.948 true 2.646,2.615 2.479,2.615 2.479,2.615 2.292,1.813 true 0.24,0.135 0.552,0.292 0.313,0.156 10 false *a 2.729,0.479 3.125,0.635 0.396,0.156 10 false MCI- 2.802,0.875 3.302,1.052 0.5,0.177 10 false MCVD 2.708,2.573 3.208,2.75 0.5,0.177 10 false SGND 1.635,0.656 2.177,0.875 0.542,0.219 10 false I55
*a Component with harness connected
(Telephone Transceiver Assembly)


Remove the telephone transceiver assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I55)Location & Routing

Click Connector(I55)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Telematics Transceiver Assembly

I55-5 (MCVD) - Body ground Ignition switch ON 4 to 6 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I55)Location & Routing

Click Connector(I55)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Telematics Transceiver Assembly

I55-23 (SGND) - Body ground Always Below 1 Ω
I55-7 (MCI-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK TELEPHONE MICROPHONE ASSEMBLY (OUTPUT TO TELEPHONE TRANSCEIVER ASSEMBLY)

NG

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

13.CHECK TELEPHONE MICROPHONE ASSEMBLY (OUTPUT TO TELEPHONE TRANSCEIVER ASSEMBLY)
E456925C06
1.51,0.333 1.917,0.594 0.406,0.26 0.854,1.938 1.042,1.938 1.042,1.938 1.417,1.354 true 2.5,1.865 2.313,1.865 2.313,1.865 1.958,1.365 true 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a 2.833,3.448 3.292,3.646 0.458,0.198 10 false GND 0.396,1.854 1.01,2.052 0.615,0.198 10 false MCO- 2.583,1.771 3.198,1.969 0.615,0.198 10 false MCO+ 1.594,0.344 1.958,0.542 0.365,0.198 10 false d30
*a Component with harness connected
(Telephone Microphone Assembly)


a.

Check the output waveform.

i.

Remove the telephone microphone assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


ii.

Connect an oscilloscope to terminal d30-2 (MCO+) and d30-4 (MCO-).


iii.

Turn the ignition switch ON.


iv.

Sound is input to the telephone microphone assembly when the user is closer than 125 mm (4.92 in.) from the telephone microphone assembly sound holes in the microphone case.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal d30-2 (MCO+) - d30-4 (MCO-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Ignition switch ON

2.

Sound is input to the telephone microphone assembly when the user is closer than 125 mm (4.92 in.) from the telephone microphone assembly sound holes in the microphone case.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.




Result:
Proceed to
OK
NG



OK

14.CHECK TELEPHONE TRANSCEIVER ASSEMBLY (OUTPUT TO RADIO RECEIVER ASSEMBLY)

NG

REPLACE TELEPHONE MICROPHONE ASSEMBLY

14.CHECK TELEPHONE TRANSCEIVER ASSEMBLY (OUTPUT TO RADIO RECEIVER ASSEMBLY)
E423925C77
1.5,0.229 1.906,0.49 0.406,0.26 0.885,1.115 0.698,0.438 0.698,0.438 0.542,0.438 true 0.906,1.219 0.74,1.958 0.74,1.958 0.583,1.958 true 0.354,0.031 0.667,0.229 0.313,0.198 10 false *a 1.583,0.281 2.073,0.479 0.49,0.198 10 false I55 0.083,0.354 0.698,0.552 0.615,0.198 10 false MCO+ 0.177,1.865 0.792,2.063 0.615,0.198 10 false MCO- 2.823,3.458 3.24,3.656 0.417,0.198 10 false GND
*a Component with harness connected
(Telephone Transceiver Assembly)


a.

Check the output waveform.

i.

Remove the telephone transceiver assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


ii.

Connect an oscilloscope to terminal I55-16 (MCO+) and I55-32 (MCO-).


iii.

Turn the ignition switch ON.


iv.

Sound is input to the telephone microphone assembly when the user is closer than 125 mm (4.92 in.) from the telephone microphone assembly sound holes in the microphone case.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal I55-16 (MCO+) - I55-32 (MCO-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Ignition switch ON

2.

Sound is input to the telephone microphone assembly when the user is closer than 125 mm (4.92 in.) from the telephone microphone assembly sound holes in the microphone case.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.




Result:
Proceed to
OK
NG



OK

NG

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

15.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)
a.

Disconnect the I12 radio receiver assembly connector.


b.

Disconnect the d28*1 or d30*2 telephone microphone assembly connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(I12,d28)Location & Routing

Click Connector(I12)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio Receiver Assembly

Click Connector(d28)Body>No. 1 Roof Wire>Telephone Microphone Assembly LH

I12-25 (SNS2) - d28-3 (SNS2) Always Below 1 Ω
I12-23 (MACC) - d28-1 (MACC) Always Below 1 Ω
I12-21 (MIN+) - d28-2 (MCO+) Always Below 1 Ω
I12-22 (MIN-) - d28-4 (MCO-) Always Below 1 Ω
I12-25 (SNS2) - Body ground Always 10 kΩ or higher
I12-23 (MACC) - Body ground Always 10 kΩ or higher
I12-21 (MIN+) - Body ground Always 10 kΩ or higher
I12-22 (MIN-) - Body ground Always 10 kΩ or higher
I12-24 (SGND) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(I12,d30)Location & Routing

Click Connector(I12)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio Receiver Assembly

Click Connector(d30)Body>No. 1 Roof Wire>Telephone Microphone Assembly RH

I12-25 (SNS2) - d30-3 (SNS2) Always Below 1 Ω
I12-23 (MACC) - d30-1 (MACC) Always Below 1 Ω
I12-21 (MIN+) - d30-2 (MCO+) Always Below 1 Ω
I12-22 (MIN-) - d30-4 (MCO-) Always Below 1 Ω
I12-25 (SNS2) - Body ground Always 10 kΩ or higher
I12-23 (MACC) - Body ground Always 10 kΩ or higher
I12-21 (MIN+) - Body ground Always 10 kΩ or higher
I12-22 (MIN-) - Body ground Always 10 kΩ or higher
I12-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

16.CHECK RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK RADIO RECEIVER ASSEMBLY
a.
E362172C42
1.583,0.896 1.99,1.156 0.406,0.26 2.021,2.198 2.271,3.177 2.271,3.177 2.385,3.177 true 2.167,2.198 2.531,2.76 2.531,2.76 2.646,2.76 true 1.156,2.719 1.302,2.719 1.302,2.719 1.865,2.177 true 2.448,3.094 2.906,3.292 0.458,0.198 10 false MACC 1.677,0.948 2.135,1.146 0.458,0.198 10 false I12 0.167,0.156 0.479,0.354 0.313,0.198 10 false *a 2.708,2.688 3.167,2.885 0.458,0.198 10 false MIN- 0.729,2.635 1.188,2.833 0.458,0.198 10 false SGND
*a Component with harness connected
(Radio Receiver Assembly)


Remove the radio receiver assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio Receiver Type)>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I12)Location & Routing

Click Connector(I12)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio Receiver Assembly

I12-23 (MACC) - Body ground Ignition switch ACC 4 to 6 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I12)Location & Routing

Click Connector(I12)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio Receiver Assembly

I12-22 (MIN-) - Body ground Always Below 1 Ω
I12-24 (SGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

17.CHECK TELEPHONE MICROPHONE ASSEMBLY (OUTPUT TO TELEPHONE TRANSCEIVER ASSEMBLY)

NG

17.CHECK TELEPHONE MICROPHONE ASSEMBLY (OUTPUT TO TELEPHONE TRANSCEIVER ASSEMBLY)

*1: for LHD

*2: for RHD


E456925C04
1.49,0.125 1.896,0.385 0.406,0.26 1.49,0.427 1.896,0.688 0.406,0.26 0.854,1.938 1.042,1.938 1.042,1.938 1.417,1.354 true 2.5,1.865 2.313,1.865 2.313,1.865 1.958,1.365 true 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a 2.833,3.448 3.292,3.646 0.458,0.198 10 false GND 1.573,0.177 1.938,0.375 0.365,0.198 10 false d28 0.396,1.854 1.01,2.052 0.615,0.198 10 false MCO- 2.583,1.771 3.198,1.969 0.615,0.198 10 false MCO+ 1.573,0.49 1.938,0.688 0.365,0.198 10 false d30 1.969,0.167 2.333,0.365 0.365,0.198 10 false *A 1.969,0.438 2.333,0.635 0.365,0.198 10 false *B
*A for LHD
*B for RHD
*a Component with harness connected
(Telephone Microphone Assembly)


a.

Check the output waveform.

i.

Remove the telephone microphone assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE MICROPHONE ASSEMBLY>REMOVAL


ii.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal
·

d28-2 (MCO+) - d28-4 (MCO-)*1

·

d30-2 (MCO+) - d30-4 (MCO-)*2


Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Ignition switch ON

2.

Sound is input to the telephone microphone assembly when the user is closer than 125 mm (4.92 in.) from the telephone microphone assembly sound holes in the microphone case.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.




Result:
Proceed to
OK
NG



OK

NG