Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › WHEEL OPENING MOULDING (for Front) › from 2021.07
RM38G0E _59 Vehicle Exterior _100846 EXTERIOR PANELS / TRIM _0468085 WHEEL OPENING MOULDING(for Front) A

EXTERIOR PANELS / TRIM  WHEEL OPENING MOULDING(for Front)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B623797N04
1.49,2 4.99,3.5 3.5,1.5 1,0.167 6.083,3.667 5.083,3.5 2.5,2.729 2.333,2.729 false 4.99,2.479 5.406,2.479 false 1,1.833 6.083,1.833 false 4.521,0.76 5.354,0.76 false 2,2.698 2.156,2.896 0.156,0.198 10 false ● 2.156,2.615 2.438,2.969 0.281,0.354 18 false 1 5.646,2.354 5.927,2.708 0.281,0.354 18 false 2 5.594,0.635 5.875,0.99 0.281,0.354 18 false 3 3.25,3.26 3.563,3.458 0.313,0.198 10 false x5 3.25,1.458 3.563,1.656 0.313,0.198 10 false x5 3.448,2.688 3.76,2.885 0.313,0.198 10 false x2 1.115,0.229 1.427,0.427 0.313,0.198 12 false *A 1.125,1.906 1.438,2.104 0.313,0.198 12 false *B 3.438,0.875 3.75,1.073 0.313,0.198 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT FENDER WHEEL ORNAMENT PAD - (Click here) - -
2 FRONT FENDER MOULDING SUB-ASSEMBLY LH 75602A (Click here) - -
3 FRONT FENDER MOULDING SUB-ASSEMBLY LH 75602A (Click here) - -

*A for GR SPORT *B except GR SPORT
● Non-reusable part - -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT FENDER WHEEL ORNAMENT PAD (except GR SPORT)

Z101186

NOTICE:

When installing the front fender wheel ornament pad, heat the front fender moulding sub-assembly LH and front fender wheel ornament pad using a heat light.



Standard Value:
Part Temperature
Front Fender Moulding Sub-assembly LH 20 to 30°C (68 to 86°F)
Front Fender Wheel Ornament Pad 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the front fender moulding sub-assembly LH and front fender wheel ornament pad excessively.


a.
B623800C03
3.865,1.542 3.958,1.74 3.958,1.74 4.031,1.531 true 3.021,2.156 3.135,1.969 3.135,1.969 2.948,2 true 3.875,1.75 4.042,1.969 0.167,0.219 10 true *a 3.188,1.844 3.354,2.063 0.167,0.219 10 true *a 2.063,0.146 2.344,0.5 0.281,0.354 18 false i 1.302,1.479 1.583,1.833 0.281,0.354 18 false ii 3.25,1.385 3.531,1.74 0.281,0.354 18 false iii
*a Mark-off Line - -


i.

Clean the surface of the front fender moulding sub-assembly LH.

1. When reusing the front fender moulding sub-assembly LH, remove remaining double-sided tape from the front fender moulding sub-assembly LH.

2. Using a heat light, heat the front fender moulding sub-assembly LH surface.

3. Remove any remaining double-sided tape from the front fender moulding sub-assembly LH.

4. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the front fender wheel ornament pad with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Clean a new front fender moulding sub-assembly LH surface.




ii.

Using a heat light, heat the front fender moulding sub-assembly LH and a new front fender wheel ornament pad.


iii.

Install the front fender wheel ornament pad in the position shown in the illustration.

NOTICE:

The application strength of the front fender wheel ornament pad will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:
·

Make sure that the end of the front fender wheel ornament pad is between the mark-off lines.

·

Apply pressure so that it does not lift up from the front fender moulding sub-assembly LH.





Hide 75602A 2.INSTALL FRONT FENDER MOULDING SUB-ASSEMBLY LH (except GR SPORT)

Z101186

NOTICE:

When installing the front fender moulding sub-assembly LH, heat the front fender sub-assembly LH and front fender moulding sub-assembly LH using a heat light.



Standard Value:
Part Temperature
Front Fender Sub-assembly LH 40 to 60°C (104 to 140°F)
Front Fender Moulding Sub-assembly LH 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the front fender sub-assembly LH and front fender moulding sub-assembly LH excessively.


a.
B617108C03
5.042,0.563 5.125,0.146 5.125,0.146 5.292,0.146 true 2.865,1.938 3.042,2.229 0.177,0.292 18 true v 6.24,0.188 6.448,0.479 0.208,0.292 18 false i 6.208,0.854 6.385,1.146 0.177,0.292 18 false ii 5.313,0.031 5.521,0.26 0.208,0.229 10 true *a 2.896,2.854 3.094,3.135 0.198,0.281 18 true iv 4.885,1.948 5.063,2.24 0.177,0.292 18 true v 3.5,0.563 3.688,0.823 0.188,0.26 18 true iii 2.563,3.26 2.76,3.542 0.198,0.281 18 true iv 3.896,2.844 4.094,3.125 0.198,0.281 18 true iv 4.729,3.073 4.927,3.354 0.198,0.281 18 true iv 4.927,3.406 5.125,3.688 0.198,0.281 18 true iv
*a Double-sided Tape - -
V100135

Screw
V100136

Clip


i.

Clean the surface of the front fender sub-assembly LH.

1. Using a heat light, heat the front fender sub-assembly LH surface.

2. Remove any remaining double-sided tape from the front fender sub-assembly LH.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the front fender moulding sub-assembly LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Using a heat light, heat the front fender sub-assembly LH and front fender moulding sub-assembly LH.


iii.

Attach the claw, clip and double-sided tape and install the front fender moulding sub-assembly LH.

NOTICE:

The application strength of the front fender moulding sub-assembly LH will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the front fender sub-assembly LH.



iv.

Install the 5 clips.


v.

Using a 4 mm hexagon socket wrench, install the 2 screws.



Hide 75602A 3.INSTALL FRONT FENDER MOULDING SUB-ASSEMBLY LH (for GR SPORT)

a.
B617109C02
2.552,3.281 2.729,3.573 0.177,0.292 18 true ii 2.885,2.917 3.063,3.208 0.177,0.292 18 true ii 2.865,1.948 3.073,2.219 0.208,0.271 18 true iii 3.531,0.531 3.667,0.792 0.135,0.26 18 true i 3.917,2.865 4.094,3.156 0.177,0.292 18 true ii 4.76,3.104 4.927,3.365 0.167,0.26 18 true ii 4.979,3.427 5.125,3.698 0.146,0.271 18 true ii 4.906,1.958 5.125,2.229 0.219,0.271 18 true iii
V100135

Screw
V100136

Clip


i.

Attach the claw and clip and install the front fender moulding sub-assembly LH.


ii.

Install the 5 clips.


iii.

Using a 4 mm hexagon socket wrench, install the 2 screws.