| *A | for GR SPORT | *B | except GR SPORT |
| *C | for Standard | *D | for Full Cover Type |
| ● | Non-reusable part | - | - |
Use the same procedure for the RH and LH sides.
The procedure described below is for the LH side.
75874 1.INSTALL QUARTER PANEL WHEEL OPENING MOULDING LH
|
|
| Part | Temperature |
|---|---|
| Vehicle Body | 40 to 60°C (104 to 140°F) |
| Quarter Panel Wheel Opening Moulding LH | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the vehicle body and quarter panel wheel opening moulding LH excessively.
| *a | Double-sided Tape | - | - |
|
Screw |
|
Grommet |
Clean the surface of the vehicle body.
1. Using a heat light, heat the vehicle body surface.
2. Remove any remaining double-sided tape from the vehicle body.
3. Wipe off any tape adhesive residue with cleaner.
Installing the quarter panel wheel opening moulding LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Using a heat light, heat the vehicle body and a new quarter panel wheel opening moulding LH.
Attach the clip and double-sided tape and install the quarter panel wheel opening moulding LH.
The application strength of the quarter panel wheel opening moulding LH will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.
Apply pressure so that it does not lift up from the vehicle body.
Install the grommet.
Install the screw.
51774C 2.INSTALL STEP PLATE COVER LH (for Full Cover Type)
75860A 3.INSTALL BODY ROCKER PANEL MOULDING ASSEMBLY LH (for Standard)
4.INSTALL REAR DOOR NO. 1 MOULDING PAD (except GR SPORT)
|
|
| Part | Temperature |
|---|---|
| Rear Door Lower Outside Moulding Sub-assembly LH | 20 to 30°C (68 to 86°F) |
| Rear Door No. 1 Moulding Pad | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the rear door lower outside moulding sub-assembly LH and rear door No. 1 moulding pad excessively.
| *a | Mark-off Line | - | - |
Clean the surface of the rear door lower outside moulding sub-assembly LH.
1. When reusing the rear door lower outside moulding sub-assembly LH, remove remaining double-sided tape from the rear door lower outside moulding sub-assembly LH.
2. Using a heat light, heat the rear door lower outside moulding sub-assembly LH surface.
3. Remove any remaining double-sided tape from the rear door lower outside moulding sub-assembly LH.
4. Wipe off any tape adhesive residue with cleaner.
Installing the rear door No. 1 moulding pad with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Clean a new rear door lower outside moulding sub-assembly LH surface.
Using a heat light, heat the rear door lower outside moulding sub-assembly LH and a new rear door No. 1 moulding pad.
Install the rear door No. 1 moulding pad in the position shown in the illustration.
The application strength of the rear door No. 1 moulding pad will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.
Make sure that the end of the rear door No. 1 moulding pad is between the mark-off lines.
Apply pressure so that it does not lift up from the rear door lower outside moulding sub-assembly LH.
75078 5.INSTALL REAR DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY LH (except GR SPORT)
|
|
| Part | Temperature |
|---|---|
| Rear Door Outside Panel LH | 40 to 60°C (104 to 140°F) |
| Rear Door Lower Outside Moulding Sub-assembly LH | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the rear door outside panel LH and rear door lower outside moulding sub-assembly LH excessively.
| *a | Double-sided Tape | - | - |
|
Screw |
|
Clip |
Clean the surface of the rear door outside panel LH.
1. Using a heat light, heat the rear door outside panel LH surface.
2. Remove any remaining double-sided tape from the rear door outside panel LH.
3. Wipe off any tape adhesive residue with cleaner.
Installing the rear door lower outside moulding sub-assembly LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Using a heat light, heat the rear door outside panel LH and rear door lower outside moulding sub-assembly LH.
Attach the clip and double-sided tape and install the rear door lower outside moulding sub-assembly LH.
The application strength of the rear door lower outside moulding sub-assembly LH will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.
Apply pressure so that it does not lift up from the rear door outside panel LH.
Install the 3 clips.
Using a 4 mm hexagon socket wrench, install the screw.
75078 6.INSTALL REAR DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY LH (for GR SPORT)
|
Screw |
|
Clip |
Attach the clip and install the rear door lower outside moulding sub-assembly LH.
Install the 3 clips.
Using a 4 mm hexagon socket wrench, install the screw.
75606B 7.INSTALL QUARTER OUTSIDE MOULDING SUB-ASSEMBLY LH
|
Screw |
|
Clip |
Attach the clip and install the quarter outside moulding sub-assembly LH.
Install the 2 clips.
Using a 4 mm hexagon socket wrench, install the screw.