Home › Engine / Hybrid System › F33A-FTV (EMISSION CONTROL) › EXHAUST GAS TEMPERATURE SENSOR (for Urea SCR System) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106332 F33A-FTV EMISSION CONTROL _0491915 EXHAUST GAS TEMPERATURE SENSOR(for Urea SCR System) A

F33A-FTV EMISSION CONTROL  EXHAUST GAS TEMPERATURE SENSOR(for Urea SCR System)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A493049N03
2.5,1.104 3.344,1.458 0.844,0.354 1.813,0.229 2.656,0.573 0.844,0.344 3.771,0.25 4.51,0.438 0.74,0.188 1.844,1 2.156,1 2.156,1 2.292,1.146 true 3.708,0.75 4,0.75 true 2.333,1.25 2.5,1.25 false 2.667,0.417 2.833,0.417 2.833,0.417 2.833,0.75 false 3.604,0.333 3.771,0.333 false 4.385,0.615 4.667,0.969 0.281,0.354 18 false 2 1.656,0.875 1.938,1.229 0.281,0.354 18 false 1 2.656,1.115 3.635,1.271 0.979,0.156 8 false 30 (306, 22) 2.563,1.281 3.542,1.438 0.979,0.156 8 false 26.3 (268, 19)* 3.823,0.271 4.802,0.427 0.979,0.156 8 false 30 (306, 22) 1.958,0.25 2.938,0.406 0.979,0.156 8 false 30 (306, 22) 1.865,0.406 2.844,0.563 0.979,0.156 8 false 14.2 (145, 10)*

Procedure Part Name Code
Z101186

Z101188

Z101187

1 NO. 4 EXHAUST GAS TEMPERATURE SENSOR 89425C (Click here) - -
2 NO. 1 SENSOR BRACKET 89439D (Click here) - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque * For union nut wrench use

PROCEDURE

Hide 89425C 1.INSTALL NO. 4 EXHAUST GAS TEMPERATURE SENSOR

a.
A493036C01
5.302,0.948 5.417,1.25 5.417,1.25 5.583,1.25 true 0.375,0.052 0.656,0.406 0.281,0.354 18 false i 3.854,0.063 4.135,0.417 0.281,0.354 18 false ii 1.583,0.667 1.833,0.833 0.25,0.167 10 true *a 5.583,1.167 5.833,1.333 0.25,0.167 10 true *b
*a Torque Wrench Fulcrum Length *b Sensor wire tube


i.

Using a 14 mm union nut wrench, install the No. 4 exhaust gas temperature sensor.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

HINT:

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

When using a union nut wrench (fulcrum length of 25 mm (0.984 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 26.3 N*m (268 kgf*cm, 19 ft.*lbf)



ii.

Connect the No. 4 exhaust gas temperature sensor connector and hang the sensor wire tube with the 2 wire clamps.



Hide 89439D 2.INSTALL NO. 1 SENSOR BRACKET

a.
A493037C01
2.292,0.656 2.167,0.5 2.167,0.5 2,0.5 true 0.917,0.104 2.844,0.458 1.927,0.354 18 false i - iii 4.01,0.427 4.167,0.625 0.156,0.198 10 true A 5.188,0.74 5.344,0.938 0.156,0.198 10 true B 1.667,0.917 1.917,1.083 0.25,0.167 10 true *a 1.667,0.438 2,0.583 0.333,0.146 10 true SST
*a Torque Wrench Fulcrum Length - -


i.

Temporarily install the No. 1 sensor bracket with the 2 bolts.


ii.

Using SST, tighten the bolt A.

SST
09729-00120  

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

HINT:

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

When using SST (fulcrum length of 200 mm (7.87 in.)) + torque wrench (fulcrum length of 180 mm (11.8 in.)): 14.2 N*m (145 kgf*cm, 10 ft.*lbf)



iii.

Tighten the bolt B.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)