| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | CENTER EXHAUST PIPE ASSEMBLY | 17420 | ( ) |
- | - |
| 2 | TAIL EXHAUST PIPE ASSEMBLY | 17430 | ( ) |
- | - |
| 5 | INSPECT FOR EXHAUST GAS LEAK | - | ( ) |
- | - |
| *A | w/ DPF | - | - |
| *1 | EXHAUST PIPE SUPPORT | *2 | COMPRESSION SPRING |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 3 | CENTER EXHAUST PIPE ASSEMBLY | 17420 | ( ) |
- | - |
| 4 | TAIL EXHAUST PIPE ASSEMBLY | 17430 | ( ) |
- | - |
| 5 | INSPECT FOR EXHAUST GAS LEAK | - | ( ) |
- | - |
| *A | w/o DPF | - | - |
| *1 | EXHAUST PIPE SUPPORT | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
17420 1.INSTALL CENTER EXHAUST PIPE ASSEMBLY (w/ DPF)
Using a vernier caliper, measure the free length of the compression spring.
43 mm (1.69 in.)
If the free length is less than the minimum, replace the compression spring.
| *1 | Gasket | - | - |
| *a | Wooden Block | - | - |
Temporarily install a new gasket to the front exhaust pipe assembly.
Using a plastic-faced hammer and wooden block, tap in the gasket until its surface is flush with the front exhaust pipe assembly.
Be sure to install the gasket so that it faces the correct direction.
Do not reuse the gasket.
Do not damage the gasket.
When connecting the center exhaust pipe assembly, do not push in the gasket with the center exhaust pipe assembly.
Install the center exhaust pipe assembly to the exhaust pipe support.
Install the center exhaust pipe assembly to the front exhaust pipe assembly with the 2 compression springs and 2 bolts.
17430 2.INSTALL TAIL EXHAUST PIPE ASSEMBLY (w/ DPF)
Using a vernier caliper, measure the free length of the compression spring.
42 mm (1.65 in.)
If the free length is less than the minimum, replace the compression spring.
| *1 | Gasket | - | - |
| *a | Wooden Block | - | - |
Temporarily install a new gasket to the center exhaust pipe assembly.
Using a plastic-faced hammer and wooden block, tap in the gasket until its surface is flush with center exhaust pipe assembly.
Be sure to install the gasket so that it faces the correct direction.
Do not reuse the gasket.
Do not damage the gasket.
When connecting the tail exhaust pipe assembly, do not push in the gasket with the tail exhaust pipe assembly.
Install the tail exhaust pipe assembly to the 3 exhaust pipe supports.
Connect the tail exhaust pipe assembly to the center exhaust pipe assembly with the 2 compression springs and 2 bolts.
17420 3.INSTALL CENTER EXHAUST PIPE ASSEMBLY (w/o DPF)
Install a new gasket.
Do not reuse the gaskets.
Install the center exhaust pipe assembly to the exhaust pipe support.
Connect the center exhaust pipe assembly to the front exhaust pipe assembly with the 2 bolts.
17430 4.INSTALL TAIL EXHAUST PIPE ASSEMBLY (w/o DPF)
Install a new gasket.
Do not reuse the gaskets.
Install the tail exhaust pipe assembly to the 4 exhaust pipe supports.
Connect the tail exhaust pipe assembly to the center exhaust pipe assembly with the 2 nuts.
5.INSPECT FOR EXHAUST GAS LEAK
If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.