Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › CAMSHAFT POSITION SENSOR › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0492064 CAMSHAFT POSITION SENSOR A

F33A-FTV ENGINE CONTROL  CAMSHAFT POSITION SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A516000N01
2.031,0.125 2.667,0.323 0.635,0.198 1.979,0.969 2.469,0.677 2.469,0.677 2.99,0.677 false 2.177,1.25 2.854,1.25 false 1.51,0.458 1.51,0.219 1.51,0.219 2.031,0.219 false 3.313,0.542 3.594,0.896 0.281,0.354 18 false 1 2.917,1.188 3.073,1.385 0.156,0.198 10 false ● 2.063,0.135 2.74,0.302 0.677,0.167 8 false 10 (102, 7)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 CAMSHAFT POSITION SENSOR 11101E (Click here) - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part
V100135

Engine oil - -

CAUTION / NOTICE / HINT

PROCEDURE

Hide 11101E 1.INSTALL CAMSHAFT POSITION SENSOR

a.
A516001C01
3.021,1.115 2.625,1.115 false 4.698,1.854 4.698,1.635 false 4.677,3.156 4.677,2.938 false 5.792,1.708 5.792,1.49 false 5.813,3.094 5.813,2.875 false 4.708,2.427 4.875,2.188 4.875,2.188 5.042,2.188 true 6.552,2.844 6.302,2.844 false 6.354,1.76 6.167,1.76 6.167,1.76 6.042,1.635 false 6.417,0.802 6.25,0.802 6.25,0.802 6.052,0.927 false 5.479,2.354 5.76,2.354 false 4.708,1.104 4.906,0.802 4.906,0.802 5.073,0.802 true 4.615,1.875 4.927,2.031 0.313,0.156 10 false *1 3.083,1.01 3.396,1.167 0.313,0.156 10 false *b 4.146,0.833 4.458,0.99 0.313,0.156 10 false *c 4.167,2.229 4.479,2.385 0.313,0.156 10 false *d 5.135,0.688 5.448,0.844 0.313,0.156 10 false *a 4.604,3.177 4.917,3.333 0.313,0.156 10 false *1 5.708,1.719 6.021,1.875 0.313,0.156 10 false *1 5.75,3.115 6.063,3.271 0.313,0.156 10 false *1 6.5,0.698 6.813,0.854 0.313,0.156 10 false *a 6.417,1.677 6.729,1.833 0.313,0.156 10 false *a 5.333,2.26 5.646,2.417 0.313,0.156 10 false *a 6.573,2.76 6.885,2.917 0.313,0.156 10 false *a 5.094,2.104 5.406,2.26 0.313,0.156 10 false *a 4.844,1.188 5.063,1.396 0.219,0.208 10 false A 4.844,2.521 5.063,2.729 0.219,0.208 10 false B 4.427,1.198 4.563,1.365 0.135,0.167 10 true A 4.427,2.531 4.563,2.698 0.135,0.167 10 true B 5.854,0.625 6.448,0.917 0.594,0.292 10 false A - A 5.896,1.979 6.49,2.271 0.594,0.292 10 false B - B 0.458,0.188 1.01,0.542 0.552,0.354 18 false i, ii 0.417,1.958 0.969,2.313 0.552,0.354 18 true iii, iv
*1 O-ring - -
*a Seam *b Camshaft Position Sensor Tip
*c Correct *d Incorrect


i.

Perform this procedure only when reusing the camshaft position sensor.

1.

Clean the O-ring groove of the camshaft position sensor.

NOTICE:

Make sure the O-ring groove is free of foreign matter.


2.

Install a new O-ring to the camshaft position sensor.

NOTICE:

Set the O-ring on the tip of the camshaft position sensor and roll it into the O-ring groove with bare hands to install it.


3.

Check if the O-ring is twisted.

HINT:

Check the entire circumference of the seam of the O-ring for twisting.




ii.

Apply a light coat of engine oil to the O-ring of the camshaft position sensor.


iii.

Install the camshaft position sensor with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

If the camshaft position sensor has been struck or dropped, replace it.

·

Make sure that the O-ring is not cracked or moved out of place when installing the camshaft position sensor.




iv.

Connect the camshaft position sensor connector.