Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › CRANKSHAFT POSITION SENSOR › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0492065 CRANKSHAFT POSITION SENSOR A

F33A-FTV ENGINE CONTROL  CRANKSHAFT POSITION SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A516002N01
1.292,0.927 1.99,1.115 0.698,0.188 1.51,2.104 1.656,2.104 1.656,2.104 1.729,1.865 false 2.125,2.063 2.375,1.594 2.375,1.594 2.625,1.594 false 1.042,1.438 1.042,1.021 1.042,1.021 1.292,1.021 false 1.313,1.958 1.521,2.281 0.208,0.323 18 false 1 2.677,1.51 2.833,1.708 0.156,0.198 10 false ● 1.344,0.948 2.271,1.115 0.927,0.167 8 false 10 (102, 7)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 CRANKSHAFT POSITION SENSOR 11401G (Click here) - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part
V100135

Engine oil - -

A487300N24
2.635,2.927 3.438,3.115 0.802,0.188 5.906,2.698 6.656,2.896 0.75,0.198 1.958,2.458 1.958,2.938 false 0.875,1.448 1,1.01 1,1.01 1.208,1.01 false 3.729,2.219 3.729,2.688 3.729,2.688 3.906,2.688 false 5.698,1.781 5.698,2.25 false 2.948,2.438 2.948,2.917 false 6.26,2.208 6.26,2.688 false 1.667,2.708 1.927,2.896 0.26,0.188 10 false x 2 3.979,2.521 4.25,2.865 0.271,0.344 18 false 3 5.646,2.281 5.917,2.625 0.271,0.344 18 false 2 6.354,2.094 6.583,2.281 0.229,0.188 10 false x 4 1.865,2.979 2.094,3.167 0.229,0.188 10 false *1 3.052,2.323 3.323,2.5 0.271,0.177 10 false x 5 1.281,0.938 1.51,1.125 0.229,0.188 10 false *2 0.938,2.083 1.188,2.26 0.25,0.177 10 false x 2 2.74,2.948 3.396,3.104 0.656,0.156 8 false 29 (296, 21) 5.969,2.729 6.729,2.885 0.76,0.156 8 false 29 (296, 21)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 NO. 2 ENGINE UNDER COVER ASSEMBLY 51420 - - -
2 NO. 1 ENGINE UNDER COVER ASSEMBLY 51410 - - -

*1 ENGINE SIDE COVER SUB-ASSEMBLY LH *2 ENGINE SIDE COVER SUB-ASSEMBLY RH
V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part

CAUTION / NOTICE / HINT

PROCEDURE

Hide 11401G 1.INSTALL CRANK POSITION SENSOR

a.
A516003C01
2.698,0.708 2.427,0.708 false 4.688,1.854 4.688,1.635 false 4.688,3.188 4.688,2.969 false 5.792,1.729 5.792,1.51 false 5.813,3.083 5.813,2.865 false 4.708,2.438 4.906,2.135 4.906,2.135 5.073,2.135 true 6.542,2.844 6.292,2.844 false 6.365,1.781 6.177,1.781 6.177,1.781 6.052,1.656 false 6.427,0.781 6.26,0.781 6.26,0.781 6.063,0.906 false 5.469,2.344 5.75,2.344 false 4.708,1.021 4.906,0.719 4.906,0.719 5.073,0.719 true 4.625,1.885 4.938,2.042 0.313,0.156 10 false *1 2.75,0.563 3.063,0.719 0.313,0.156 10 false *b 4.177,0.656 4.49,0.813 0.313,0.156 10 false *c 4.177,2.135 4.49,2.292 0.313,0.156 10 false *d 5.146,0.625 5.458,0.781 0.313,0.156 10 false *a 4.625,3.198 4.938,3.354 0.313,0.156 10 false *1 5.719,1.74 6.031,1.896 0.313,0.156 10 false *1 5.729,3.115 6.042,3.271 0.313,0.156 10 false *1 6.5,0.677 6.813,0.833 0.313,0.156 10 false *a 6.417,1.667 6.729,1.823 0.313,0.156 10 false *a 5.313,2.24 5.625,2.396 0.313,0.156 10 false *a 6.583,2.74 6.896,2.896 0.313,0.156 10 false *a 5.115,2.052 5.427,2.208 0.313,0.156 10 false *a 4.865,1.177 5.083,1.385 0.219,0.208 10 false A 4.854,2.5 5.073,2.708 0.219,0.208 10 false B 4.427,1.167 4.563,1.333 0.135,0.167 10 true A 4.448,2.49 4.583,2.656 0.135,0.167 10 true B 5.885,0.594 6.479,0.885 0.594,0.292 10 false A - A 5.865,2.031 6.458,2.323 0.594,0.292 10 false B - B 0.448,0.083 1,0.438 0.552,0.354 18 false i, ii 0.448,1.958 0.938,2.24 0.49,0.281 18 true iii, iv
*1 O-ring - -
*a Seam *b Crankshaft Position Sensor Tip
*c Correct *d Incorrect


i.

Perform this procedure only when reusing the crankshaft position sensor.

1. Clean the O-ring groove of the crankshaft position sensor.

NOTICE:

Make sure the O-ring groove is free of foreign matter.


2. Install a new O-ring to the crankshaft position sensor.

NOTICE:

Set the O-ring on the tip of the crankshaft position sensor and roll it into the O-ring groove with bare hands to install it.


3. Check if the O-ring is twisted.

HINT:

Check the entire circumference of the seam of the O-ring for twisting.



ii.

Apply a light coat of engine oil to the O-ring of the crankshaft position sensor.


iii.

Install the crankshaft position sensor with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

If the crankshaft position sensor has been struck or dropped, replace it.

·

Make sure that the O-ring is not cracked or moved out of place when installing the crankshaft position sensor.




iv.

Connect the crankshaft position sensor connector.



Hide 51420 2.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 51410 3.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY