Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › CRANKSHAFT POSITION SENSOR › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0492065 CRANKSHAFT POSITION SENSOR A

F33A-FTV ENGINE CONTROL  CRANKSHAFT POSITION SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A487300N23
1.958,2.458 1.958,2.938 false 0.875,1.448 1,1.01 1,1.01 1.208,1.01 false 3.729,2.219 3.729,2.688 3.729,2.688 3.906,2.688 false 5.698,1.781 5.698,2.25 false 1.51,2.875 1.74,3.063 0.229,0.188 10 false x 2 3.969,2.542 4.24,2.885 0.271,0.344 18 false 1 5.646,2.281 5.917,2.625 0.271,0.344 18 false 2 6.198,2.219 6.427,2.406 0.229,0.188 10 false x 4 1.885,2.969 2.115,3.156 0.229,0.188 10 false *1 2.906,2.479 3.177,2.656 0.271,0.177 10 false x 5 1.26,0.938 1.49,1.125 0.229,0.188 10 false *2 0.781,2.25 1.01,2.438 0.229,0.188 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 NO. 1 ENGINE UNDER COVER ASSEMBLY 51410 - - -
2 NO. 2 ENGINE UNDER COVER ASSEMBLY 51420 - - -

*1 ENGINE SIDE COVER SUB-ASSEMBLY LH *2 ENGINE SIDE COVER SUB-ASSEMBLY RH

A495099N01
1.51,2.104 1.656,2.104 1.656,2.104 1.729,1.865 false 2.125,2.063 2.375,1.594 2.375,1.594 2.625,1.594 false 1.313,1.958 1.521,2.281 0.208,0.323 18 false 3 2.677,1.531 2.833,1.729 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

3 CRANKSHAFT POSITION SENSOR 11401G (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

PROCEDURE

Hide 51410 1.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 51420 2.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 11401G 3.REMOVE CRANKSHAFT POSITION SENSOR

a.
A495101N01
0.604,0.021 1.021,0.354 0.417,0.333 18 true i, ii 4.49,0.219 4.906,0.552 0.417,0.333 18 false iii

i.

Disconnect the crankshaft position sensor connector.


ii.

Remove the bolt and crankshaft position sensor.

NOTICE:

If the crankshaft position sensor has been struck or dropped, replace it.



iii.

Perform this procedure only when reusing the crankshaft position sensor.

1. Remove the O-ring from the crankshaft position sensor.

NOTICE:
·

Make sure to only remove the O-ring with bare hands.

·

When removing the O-ring, be careful not to damage the O-ring groove of the crankshaft position sensor.

·

If the O-ring groove of the crankshaft position sensor is damaged, replace the crankshaft position sensor with a new one.