Home › Engine / Hybrid System › F33A-FTV (FUEL) › FUEL FILTER (for Fuel Tank Side) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106331 F33A-FTV FUEL _0492271 FUEL FILTER(for Fuel Tank Side) A

F33A-FTV FUEL  FUEL FILTER(for Fuel Tank Side)  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the fuel filter element assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
Battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:
·

Make sure there are no scratches or foreign objects before and after the work.

·

Check the area around the fuel filter assembly for dirt and clean it if it is, before work.



HINT:

When replacing the fuel filter element assembly, use TOYOTA genuine parts.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 3.REMOVE SPARE TIRE

Hide 4.DISCONNECT FUEL HOSE

a.
A487522

Slide the 2 clamps and disconnect the 2 fuel hoses from fuel filter assembly.


Hide 5.DRAIN FUEL

a.
A487521

Place the container under the fuel filter drain plug.


b.

Loosen the fuel filter drain plug by hand and drain fuel from the fuel filter assembly.


c.

Tighten the fuel filter drain plug by hand.


Hide 23300 6.REMOVE FUEL FILTER ASSEMBLY

a.
A487523

w/ Fuel Heater:

Disconnect the 2 connectors from the fuel filter assembly.


b.
A487524

Detach the clamp and disconnect the 2 connectors from the fuel filter assembly.


c.
A487525

Remove the 3 bolts and fuel filter assembly.


Hide 23921B 7.REMOVE FUEL FILTER BRACKET

a.
A487526

Remove the bolt and fuel filter bracket from the fuel filter assembly.


Hide 23921 8.REMOVE FUEL FILTER SUPPORT

a.
A487527

Remove the bolt and fuel filter support from the fuel filter assembly.


Hide 23931A 9.REMOVE FUEL FILTER COVER

a.
A487528

Detach the 2 clips and remove the fuel filter cover from the fuel filter assembly.


Hide 23382 10.REMOVE FUEL FILTER CASE

a.
A487529

Detach the clamp and disconnect the wire harness from the fuel filter case.


b.

Mount the fuel filter assembly in a vise between aluminum plates.

NOTICE:
·

Do not tighten the vise more than necessary.

·

Do not damage the fuel filter cap.




c.
A487537C01
2.802,1 3.052,1 true 3.083,0.896 3.323,1.094 0.24,0.198 10 false *a
*a Hexagon Part


Using the hexagonal portion, remove the fuel filter case from the fuel filter cap.


Hide 23390 11.REMOVE FUEL FILTER ELEMENT ASSEMBLY

a.
A487530

Remove the fuel filter element assembly from the fuel filter case.


Hide 23344A 12.REMOVE FUEL FILTER ELEMENT GASKET

a.
A487531

Remove the fuel filter element gasket from the fuel filter case.


Hide 23344A 13.INSTALL FUEL FILTER ELEMENT GASKET

a.

Remove any dirt and foreign matter on the mounting surface and inside of the fuel filter cap and fuel filter case.


b.

Apply a light coat of gasoline to a new fuel filter element gasket and install it to the fuel filter case.


Hide 23390 14.INSTALL FUEL FILTER ELEMENT ASSEMBLY

a.

Install a new fuel filter element assembly to the fuel filter case.


Hide 23382 15.INSTALL FUEL FILTER CASE

a.

Using the hexagonal portion, install the fuel filter case to the fuel filter cap.

Torque:
19.6 N*m (200 kgf*cm, 14 ft.*lbf)


b.

Attach the clamp and connect the wire harness to the fuel filter case.


Hide 23931A 16.INSTALL FUEL FILTER COVER

a.

Attach the 2 clips and install the fuel filter cover to the fuel filter assembly.


Hide 23921 17.INSTALL FUEL FILTER SUPPORT

a.

Install the fuel filter support to the fuel filter assembly with the bolt.

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)


Hide 23921B 18.INSTALL FUEL FILTER BRACKET

a.

Install the fuel filter bracket to the fuel filter assembly with the bolt.

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)


Hide 23300 19.INSTALL FUEL FILTER ASSEMBLY

a.

Install the fuel filter assembly with the 3 bolts.

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)


b.
A494340

Attach the clamp and connect the connector to the fuel filter assembly.


c.

w/ Fuel Heater:

Connect the 2 connectors to the fuel filter assembly.


Hide 20.CONNECT FUEL HOSE

a.

Connect the 2 fuel hoses to the fuel filter assembly, and slide the 2 clamps to secure the 2 hoses.


Hide 21.INSTALL SPARE TIRE

Hide 22.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 23.RESET FUEL SYSTEM WARNING

a.

Turn the ignition switch to ON.


b.
A492342

After turning the ignition switch to ON, connect the connector no sooner than 3 seconds have passed but no later than 60 seconds have passed.


c.

Check that the fuel system warning turns off.


Hide 25. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART