DESCRIPTION (ECD SYSTEM)
Vehicle Control History is a function that captures and stores ECU data when triggered by specific vehicle behavior.
If the customer states that the engine stalled or will not start, it may be possible to diagnose the cause of the malfunction by checking the vehicle history information and freeze frame data.
The number of possible stored Freeze Frame Data sets, whether multi Freeze Frame Data is available, the number of freeze frame points, Freeze Frame Data items, the ECU internal range, etc., is different depending on the stored group.
The stored data items for Vehicle Control History Freeze Frame Data are different depending on the stored group. When the value of a data item does not change across all points, only the value of the detection point will be displayed. The content of the Freeze Frame Data is almost the same as that of the Data List.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DATA LIST / ACTIVE TEST
PRECAUTIONS (ECD SYSTEM)
As Vehicle Control History may be overwritten whenever the trigger conditions are met, make sure to save Vehicle Control History before performing any inspections.
As Vehicle Control History may be stored when performing an Active Test, learning, etc., make sure to clear the Vehicle Control History before returning the vehicle to the customer.
CHECK VEHICLE CONTROL HISTORY (ECD SYSTEM)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
It is also possible to display Vehicle Control History during the Health Check, if "Store All Data" is selected.
| Stored Group | Number of Records | Number of Freeze Frame Points | Multi Freeze Frame Data Sampling Period | Note |
|---|---|---|---|---|
| 03 | 1 code
|
7 points (1 point at detection + 6 points before detection)
|
0.5 seconds | The data can be cleared by using the GTS or by disconnecting the cable from the negative (-) battery terminal. |
| 04 | 1 code
|
7 points (1 point at detection + 6 points before detection)
|
0.5 seconds | The data can be cleared by using the GTS or by disconnecting the cable from the negative (-) battery terminal. |
| 05 | 4 codes
|
1 point (multi freeze frame data not available) | - |
·
The data can be cleared by using the GTS.
·
The data cannot be cleared by disconnecting the cable from the negative (-) battery terminal. |
| 08 | 1 codes
|
12 points (1 point at detection + 8 points before detection + 3 points after detection)
|
0.5 seconds |
·
The data can be cleared by using the GTS.
·
The data cannot be cleared by disconnecting the cable from the negative (-) battery terminal. |
| 09 | 1 code
|
7 points (1 point at detection + 3 points before detection + 3 points after detection)
|
0.5 seconds | The data can be cleared by using the GTS or by disconnecting the cable from the negative (-) battery terminal. |
Multi Freeze Frame Data makes it possible to display the engine condition (ECU data) both before and after the trigger detection point.
The number of available points differs depending on the stored group.
When the value of a data item does not change across all points, only the value at the detection point will be displayed.
Only 1 measurement point can be displayed for stored group 05 Freeze Frame Data.
CLEAR VEHICLE CONTROL HISTORY (ECD SYSTEM)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB) (Clear).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
By performing this procedure, all stored Vehicle Control History items will be cleared.
VEHICLE CONTROL HISTORY FREEZE FRAME DATA (ECD SYSTEM)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Select a vehicle control history item to access the applicable freeze frame data.
Check the freeze frame Data recorded with the Vehicle Control History.
CHECK VEHICLE CONTROL HISTORY (AUTOMATIC TRANSMISSION SYSTEM)
The vehicle control history (automatic transmission system) stores the history of system protection operations.
The number of occurrences is stored for each item.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
| Code | Tester Display | Measurement Item | Diagnostic Note |
|---|---|---|---|
| X090A | Limited Slip Differential Speed Higher than Expected | History of high differential control operation while driving |
·
Shift operation is prohibited to protect the differential when driving on a road with different friction between the left and right drive wheels and it is predicted that a large rotational difference will occur due to slip at one of the wheels.
·
It can be understood that one of the wheels slipped. |
| X090B | Lock Up On (High A/T Oil Temperature) | History of lock-up control operation due to the A/T fluid rising to a high temperature | Switches to a shift line that restricts the engine speed until the A/T fluid temperature drops, in order to protect the A/T. |
CLEAR VEHICLE CONTROL HISTORY (AUTOMATIC TRANSMISSION SYSTEM)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB) (Clear).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
By performing this procedure, all stored Vehicle Control History items will be cleared.
CLEAR VEHICLE CONTROL HISTORY (AUTOMATIC TRANSMISSION SYSTEM)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB) (Clear).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Select a vehicle control history item to access the applicable freeze frame data.
Check the freeze frame Data recorded with the Vehicle Control History.
| Tester Display | Description |
|---|---|
| Acceleration Sensor Correct Value | Acceleration sensor calibration value |
| Throttle Position for Shift Point Control | Throttle position for shift point control |
| Stop Light SW | Brake pedal operation availability |
| Shift Range Signal | Shift position |
| Turbine Rotation Speed | Input shaft speed |
| Speed (SP2) | ECT vehicle speed |
| A/T Oil Temperature No.1 | ATF temperature sensor value |
| Output Axis Speed | Output shaft speed |
| Limited Slip Differential Speed Higher than Expected Count | Occurrence count of Limited Slip Differential Speed Higher than Expected |
| Lock Up On Count (High A/T Oil Temperature) | Occurrence count of Lock Up On (High A/T Oil Temperature) |
VEHICLE CONTROL HISTORY (AIRBAG SYSTEM)
A part of the control history can be confirmed using the vehicle control history.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>VEHICLE CONTROL HISTORY