Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484891 ECD SYSTEM(w/o DPF) J

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  Turbocharger Noise  


DESCRIPTION

HINT:

Turbocharger noise is classified into two types. These are whistling sound and chattering sound. During troubleshooting, first determine the type of noise.


Type of Abnormal Noise Outline of Abnormal Noise Major Trouble Area
Whistling sound (airflow sound) The whistling sound volume and pitch are proportional to the turbocharger or engine speed. The abnormal noise level becomes clear when the engine speed is increased.
·

Turbocharger (example: unstable shaft)

·

Engine gear (oil pump gear, etc.)

·

Transmission gears

·

Leak in intake system

·

Damaged intake system


HINT:

*: Refer to the illustration


Chattering sound (metallic sound) The chattering sound pitch is lower than the whistling sound pitch. Has a comparatively constant pitch that is independent of the engine speed and vehicle speed. Turbocharger
HINT:
·

The turbocharger vibrations are transmitted to the exhaust pipe, causing noise and resonance.

·

The turbocharger vibrations are transmitted through the exhaust pipe to the chassis (floor), causing noise and resonance in the chassis.




A478404E03
2.5,2.427 4.313,2.948 1.813,0.521 0.115,2.156 1.865,3.219 1.75,1.063 4.917,2.156 6.667,3.219 1.75,1.063 3.396,6 3.396,5.052 true 1.771,5.865 2.646,5.177 true 5.01,5.885 4.167,5.156 true 1.271,4.958 1.844,5.167 0.573,0.208 10 false Intake 1.031,5.896 2.479,6.115 1.448,0.219 10 false Compressor Wheel 4.896,5.917 6.26,6.094 1.365,0.177 10 false Turbine Wheel 3.208,6.031 4.292,6.26 1.083,0.229 10 false Shaft 5.24,4.948 5.896,5.167 0.656,0.219 10 false Exhaust 2.948,2.604 4.427,3.24 1.479,0.635 10 false Shaft vibrates 0.177,2.448 1.792,3.042 1.615,0.594 10 false Turbine wheel/compressor wheel rotate 5.073,2.448 6.531,3.177 1.458,0.729 10 false Turbocharger operating sound 0.135,0.104 5.281,0.302 5.146,0.198 10 false [Turbocharger Operating Sound Generating Mechanism] 0.146,0.521 5.354,0.719 5.208,0.198 10 false The turbocharger makes an operating sound due to the shaft vibration. 0.177,0.885 5.042,1.135 4.865,0.25 10 false Note that this sound may get louder due to deterioration of parts.

Faults and Symptoms of Diesel Engine Components



Turbocharger System
Main fault
·

Unstable turbocharger turbine shaft (interference, seizing, poor balance, etc.)


Symptom
·

High-pitched whistling sound

HINT:

The volume and pitch are proportional to the turbocharger speed.


·

Metallic sound due to looseness



Intake System
Main fault Leak
Symptom Abnormal noise during intake leak

Engine Gear
Symptom Gear noise
HINT:

The volume and pitch are proportional to the engine speed.



Transmission Gears
Symptom Gear noise
HINT:

The volume and pitch are proportional to the transmission gear speed.



PROCEDURE

1.CONFIRM CONDITION IN WHICH NOISE OCCURRED
a.

Confirm with the customer the condition when noise occurred.

HINT:

To clearly understand the conditions in which the noise occurred, the items in the table below are useful.


Item Note
Engine speed Engine speed range
Vehicle speed Vehicle speed range
Transaxle gear Which gear?
Accelerator pedal position During acceleration or deceleration?
Temperature
·

Ambient temperature

·

Engine temperature (cold, warmed up, etc.)


Road conditions
·

City or highway driving

·

Uphill or downhill


Noise level
·

Did the noise occur suddenly, or build gradually?

·

Has the noise gradually been getting louder?


Other symptoms
·

Lack of power

·

High fuel consumption, etc.


Noise recognition What made the customer determine that the sound was a malfunction?


Result:
Proceed to
NEXT



NEXT

2.PERFORM SIMULATION TEST
2.PERFORM SIMULATION TEST
a.

Check whether the noise described by the customer occurs.

HINT:

If an abnormal noise is heard, check whether it matches the noise described by the customer.


Result:
Result Proceed to
Abnormal noise generated while idling (ticking or rattling (metallic sound)) A
Abnormal noise generated while driving B




A

3.CHECK FOR NOISE FROM SOURCE OTHER THAN TURBOCHARGER

B

8.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE AIR BYPASS VALVE)
3.CHECK FOR NOISE FROM SOURCE OTHER THAN TURBOCHARGER
a.

Check for the noise source with a sound scope.


b.

The source of the noise is not the turbocharger, but a part other than the turbocharger (e.g. a part inside the engine, transmission, or vacuum pump).


c.

Sometimes gear noise may be mistaken for turbocharger noise. For gear noise, pay attention to the gear inside the engine and transmission gear.


d.

Increase the engine speed and check if the noise decreases at the same time the engine speed decreases. If the noise decreases at the same time the engine speed decreases, the noise is generated in the gears. If the noise decreases immediately after the engine speed decreases, the noise is generated in the turbocharger.

A478405E06
4.031,1.448 3.438,0.604 true 3.24,1.979 2.646,1.135 true 5.323,2.094 5.635,0.927 true 0.635,1.5 1.865,1.698 1.229,0.198 10 false Noise Level (dB) 1.281,2.938 2.51,3.135 1.229,0.198 10 false 3000 rpm 3.979,4.146 5.208,4.344 1.229,0.198 10 false Time (Second) 0.521,3.427 1.75,3.625 1.229,0.198 10 false Engine Speed 3.156,0.438 4.021,0.635 0.865,0.198 10 false Gear Noise 2.24,0.917 3.313,1.115 1.073,0.198 10 false Engine Noise 5.49,0.708 6.958,0.958 1.469,0.25 10 false Turbocharger Noise 1.125,3.958 2.354,4.156 1.229,0.198 10 false Idling


e.

Check whether the noise described by the customer occurs.

Result:
Result Proceed to
Abnormal noise generated from turbocharger A
Abnormal noise generated from parts other than turbocharger B




A

4.CHECK TURBOCHARGER SUB-ASSEMBLY

B

5.CHECK FOR NOISE FROM SOURCE OTHER THAN TURBOCHARGER (PROCEDURE 5)
4.CHECK TURBOCHARGER SUB-ASSEMBLY
a.

Check for damage to the compressor impeller.


b.

Check for interference between the compressor impeller and the compressor housing.


Result:
Result Proceed to
No damage or interference A
Damage or interference exists B



A

END (CAUSE CHECK EXCEPT THE TURBOCHARGER)

B

5.CHECK FOR NOISE FROM SOURCE OTHER THAN TURBOCHARGER (PROCEDURE 5)
a.

Check for the noise source.

CAUTION:

When performing this check, make sure that the sound scope, your body, etc., do not get caught on the V-belt.


HINT:
·

The source of the noise is not the turbocharger sub-assembly, but a part other than the turbocharger sub-assembly (e.g. a part inside the engine, transmission, or vacuum pump).

·

Sometimes gear noise may be mistaken for turbocharger noise.

For gear noise, pay attention to the gear inside the engine and transmission gear.

·

Rev the engine up and check if the noise reduces at the same time the engine speed decreases. If the noise reduces at the same time the engine speed decreases, it is gear noise. If the noise reduces a short time after the engine speed decreases, it is turbocharger noise.




Result:
Proceed to
NEXT



NEXT

6.REPLACE THE PARTS DETECTED IN PROCEDURE 5
6.REPLACE THE PARTS DETECTED IN PROCEDURE 5
a.

Replace the parts detected in procedure 5 as the noise source.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER THE NOISE PROBLEM HAS BEEN SUCCESSFULLY SOLVED
7.CONFIRM WHETHER THE NOISE PROBLEM HAS BEEN SUCCESSFULLY SOLVED
a.

Check whether the noise problem has been successfully solved.


Result:
Proceed to
NEXT



NEXT

END

8.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE AIR BYPASS VALVE)
a.

Enter the following menus: Powertrain / Engine / Active Test / Activate the Air Bypass Valve.

Powertrain > Engine > Active Test
Tester Display
Activate the Air Bypass Valve
50004 372 42039 264,265

b.

Turn the Active Test ON and OFF, and check that the air bypass valve makes an operating sound.

HINT:
·

When turning the air bypass valve from ON to OFF, the valve makes a sitting sound.

·

If it is difficult to distinguish the operating sound, repeat the Active Test and check again.

·

If no DTC related to the air bypass valve is output and an operating sound cannot be confirmed, the air bypass valve is stuck.




Result:
Result Proceed to
There is an operating sound A
There is no operating sound B



A

9.CONFIRM NOISE SOURCE (FROM TURBOCHARGER SUB-ASSEMBLY OR NOT)

B

REPLACE AIR BY-PASS VALVE ASSEMBLY

9.CONFIRM NOISE SOURCE (FROM TURBOCHARGER SUB-ASSEMBLY OR NOT)
a.

Start the engine and warm it up.


b.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VN Turbo 1 and 2 Open.

Powertrain > Engine > Active Test
Tester Display
Activate the VN Turbo 1 and 2 Open
50004 372 102

c.

Perform the Active Test under the conditions* from the time the noise occurred described by the customer and compare the noise to the noise heard when not performing the Active Test and check if the noise is reduced.

HINT:

*: Some examples of conditions are idling, racing the engine and driving at full throttle.


Result:
Result Proceed to
The noise is reduced (or disappears) A
The noise is the same as in Procedure 2 (The noise does not change) B


HINT:
·

By performing "Activate the VN Turbo 1 and 2 Open" Active Test, the variable nozzle of the turbocharger sub-assembly becomes fully open regardless of the engine condition, and the turbocharger speed does not increase.

·

If the turbocharger sub-assembly is the cause of the noise, the noise will be reduced when "Activate the VN Turbo 1 and 2 Open" Active Test is performed because turbocharger speed does not increase.





A

10.PERFORM SIMULATION TEST

B

5.CHECK FOR NOISE FROM SOURCE OTHER THAN TURBOCHARGER (PROCEDURE 5)
10.PERFORM SIMULATION TEST
a.

Check whether the noise described by the customer occurs.

HINT:

If an abnormal noise is heard, check whether it matches the noise described by the customer.



b.

If an abnormal noise is confirmed, determine which system emits it.


Result:
Result Proceed to
Noise occurs (squealing (metallic sound) when driving) A
Noise occurs (hissing (airflow sound) when driving) B
Noise occurs (whistling or foghorn-like (airflow sound) during acceleration) C
Noise occurs (whistling (airflow sound) during deceleration) D



A

11.CHECK TURBOCHARGER SUB-ASSEMBLY

B

16.CHECK TURBOCHARGER SUB-ASSEMBLY

C

22.CHECK TURBOCHARGER SUB-ASSEMBLY

D

27.CHECK GEAR NOISE
11.CHECK TURBOCHARGER SUB-ASSEMBLY
a.

Check that the turbine shaft rotates smoothly, without catching.

Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>TURBOCHARGER>INSPECTION


b.

Check for loose turbine mounting nuts and for axial play in the turbine shaft.

Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>TURBOCHARGER>INSPECTION

HINT:

If the turbine shaft catches or if there no play or excessive play, it could indicate poor sliding due to seal damage due to seizing or a deposit build-up.



Result:
Result Proceed to
No turbine shaft malfunction A
Turbine shaft malfunction B



A

12.CHECK TURBOCHARGER SUB-ASSEMBLY

B

12.CHECK TURBOCHARGER SUB-ASSEMBLY
a.

Check for damage to the compressor impeller.


b.

Check for interference between the compressor impeller and the compressor housing.


Result:
Result Proceed to
Damage or interference exists A
No damage or interference B



A

13.REPLACE TURBOCHARGER SUB-ASSEMBLY

B

15.CHECK TURBOCHARGER SUB-ASSEMBLY
13.REPLACE TURBOCHARGER SUB-ASSEMBLY
a.

Replace the turbocharger sub-assembly.

Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>TURBOCHARGER>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.PERFORM SIMULATION TEST
14.PERFORM SIMULATION TEST
a.

Check that the abnormal noise has disappeared.


Result:
Proceed to
NEXT



NEXT

END

15.CHECK TURBOCHARGER SUB-ASSEMBLY
a.

Check for interference between the turbine wheel and the turbine housing.


Result:
Result Proceed to
No damage or interference* A
Damage or interference exists B


HINT:

*: Replace the turbocharger sub-assembly, as the abnormal noise may have been caused by interference between the turbine blades and housing.



A

B

16.CHECK TURBOCHARGER SUB-ASSEMBLY
a.

Check that no soot or oil adheres to the turbocharger sub-assembly connectors.

A490896

HINT:

If adhering soot or an oil leak exists, air leaking at that position may be the cause of the abnormal noise.



Result:
Result Proceed to
No adhering soot or an oil* A
Soot adhering around the turbine housing, flange, or exhaust pipe clamp B
Oil leak from the contact surface between the compressor housing and bearing housing C
Oil adhering to the compressor flange D


HINT:

*: Since abnormal noise may be the result of airflow noise from the blades, replace the turbocharger sub-assembly.



A

17.REPLACE TURBOCHARGER SUB-ASSEMBLY

B

19.CHECK EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

C

D

REPLACE GASKET

17.REPLACE TURBOCHARGER SUB-ASSEMBLY
a.

Replace the turbocharger sub-assembly.

Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>TURBOCHARGER>REMOVAL


Result:
Proceed to
NEXT



NEXT

18.PERFORM SIMULATION TEST
18.PERFORM SIMULATION TEST
a.

Check that the abnormal noise has disappeared.


Result:
Proceed to
NEXT



NEXT

END

19.CHECK EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
a.

Check for deformation or cracks in the mounting surfaces on the exhaust manifold converter sub-assembly and the turbine with valve housing sub-assembly.

HINT:

Deformation or cracks on a mounting surface may allow exhaust gas to leak from the damaged position.


Standard:

No deformation or cracks on a mounting surface.


Result:
Result Proceed to
No problem with the mounting surface A
Deformation or cracks on the exhaust manifold converter sub-assembly mounting surface B
Deformation or cracks on the turbine with valve housing sub-assembly mounting surface C




A

20.REPLACE EXHAUST PIPE CLAMP AND GASKET

B

C

20.REPLACE EXHAUST PIPE CLAMP AND GASKET
a.

Replace the exhaust pipe clamp and the gasket.


Result:
Proceed to
NEXT



NEXT

21.PERFORM SIMULATION TEST
21.PERFORM SIMULATION TEST
a.

Check that the abnormal noise has disappeared.


Result:
Proceed to
NEXT



NEXT

END

22.CHECK TURBOCHARGER SUB-ASSEMBLY
a.

Check that the turbine shaft rotates smoothly, without catching.

Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>TURBOCHARGER>INSPECTION


b.

Check for loose turbine mounting nuts and for axial play in the turbine shaft.

Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>TURBOCHARGER>INSPECTION

HINT:

If the turbine shaft catches or if there no play or excessive play, it could indicate poor sliding due to seal damage due to seizing or a deposit build-up.



Result:
Result Proceed to
No turbine shaft malfunction A
Turbine shaft malfunction B



A

23.CHECK TURBOCHARGER SUB-ASSEMBLY

B

23.CHECK TURBOCHARGER SUB-ASSEMBLY
a.

Check for damage to the compressor impeller.


b.

Check for interference between the compressor impeller and the compressor housing.

HINT:

If the previous checks find no malfunction, replace the turbocharger sub-assembly and determine if the noise improved.



Result:
Result Proceed to
Damage or interference exists A
No damage or interference B



A

24.REPLACE TURBOCHARGER SUB-ASSEMBLY

B

26.CHECK TURBOCHARGER SUB-ASSEMBLY
24.REPLACE TURBOCHARGER SUB-ASSEMBLY
a.

Replace the turbocharger sub-assembly.

Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>TURBOCHARGER>REMOVAL


Result:
Proceed to
NEXT



NEXT

25.PERFORM SIMULATION TEST
25.PERFORM SIMULATION TEST
a.

Check that the abnormal noise has disappeared.


Result:
Proceed to
NEXT



NEXT

END

26.CHECK TURBOCHARGER SUB-ASSEMBLY
a.

Check for interference between the turbine wheel and the turbine housing.


Result:
Result Proceed to
No damage or interference* A
Damage or interference exists B


HINT:

*: Replace the turbocharger sub-assembly, as the abnormal noise may have been caused by loss of rotational balance and deterioration over time.



A

B

27.CHECK GEAR NOISE
a.

Check if gear noise is the source of the abnormal noise (not noise from the turbocharger).

Result:
Proceed to
NEXT




NEXT

ELIMINATE THE CAUSE OF THE NOISE