Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (w/o Emergency Call Service) › from 2022.11
RM38G0E _56 Audio / Visual / Telematics _100608 TELEMATICS _0562784 TELEMATICS SYSTEM(w/o Emergency Call Service) J

TELEMATICS  TELEMATICS SYSTEM(w/o Emergency Call Service)  Warning Notification Function Malfunction  


PROCEDURE

1.CHECK PROBLEM SYMPTOM (WARNING NOTIFICATION FUNCTION)
a.

Check the problem symptom.

i.

Check the problem symptom of the warning notification function.

Result:
Result Proceed to
The multi-display screen does not show a warning message even though a warning light turns on or the multi-information display indicates a warning. A
The multi-display screen shows a warning message even though a warning light is not on and the multi-information display does not indicate a warning. B
The multi-display screen shows a warning message different from the warning light or the multi-information display.


HINT:
·

The warning notification function sends information to the service center through communication.

·

Carefully confirm the conditions that caused the malfunction in order to determine if a temporary problem with the radio wave signal conditions caused the malfunction.






A

2.INSPECT WARNING LIGHT

B

7.CHECK METER WARNING LIGHT
2.INSPECT WARNING LIGHT
a.

Check if the indicated warning light or message is listed in the following table.

HINT:

Only messages listed in the table are included in the warning notification function.


Warning Name
Engine warning
Brake system warning
ABS warning
VSC warning
ECB warning
Suspension control system warning
KDSS warning
Multi-terrain select warning
EPS warning
Charging system warning
Airbag warning
Pedestrian detection warning
Drive start control system
Brake override system warning
Entry and start system with push-button start warning
Front-lighting adaptive system warning
Automatic headlight beam level control system warning
Automatic high beam system warning
LED headlight warning
Shift control system warning
Fuel system warning
Transmission fluid temperature warning
4WD system warning
Tire pressure system warning
Electric parking brake warning
Auto hold warning
BSM system warning
Secondary collision brake warning
Parking support brake system warning
Engine maintenance waring
Electric outer mirror warning
IMT warning
Engine oil level warning
Brake fluid level warning
Engine oil pressure warning
Tire pressure low warning
Washer fluid level warning
Engine oil maintenance warning
High coolant temperature warning
Fuel filter warning
DPF warning
Incorrect AdBlue warning
AdBlue level warning
Integrated system warning
Rear side rader system warning
Parking support system warning
GPF maintenance warning
Transmission system warning

Result:
Result Proceed to
Warning light or message is listed in the table. A
Warning light or message is not listed in the table. B




A

3.CHECK CAN COMMUNICATION SYSTEM

B

END

3.CHECK CAN COMMUNICATION SYSTEM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Bus Check.


e.

Check that all ECUs and sensors that use CAN communication are connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
There are no connection problems. A
There is a connection problem. B



A

4.CHECK METER WARNING LIGHT

B

4.CHECK METER WARNING LIGHT
a.

Check that the warning light of the combination meter assembly illuminates and a message displays on the multi-information display when there is a malfunction, and do not when there is not a malfunction.

OK:

There are no problems with warning lights or warning messages.


HINT:

The warning notification function of the telematics system uses the warning notification signals sent and received by the meter/gauge system. Therefore, if the meter/gauge system is not operating normally, the warning notification function will not operate normally.



Result:
Result Proceed to
OK (w/ Navigation System) A
OK (w/o Navigation System) B
NG C



A

5.CHECK NAVIGATION SYSTEM

B

6.CHECK AUDIO AND VISUAL SYSTEM

C

5.CHECK NAVIGATION SYSTEM
a.

Check if the navigation system is operating and functioning normally.

OK:

The navigation system is normal.



Result:
Proceed to
OK
NG



OK

NG

6.CHECK AUDIO AND VISUAL SYSTEM
a.

Check if the audio and visual system is operating and functioning normally.

OK:

The audio and visual system is normal.



Result:
Proceed to
OK
NG



OK

NG

7.CHECK METER WARNING LIGHT
a.

Check that the warning light of the combination meter assembly illuminates and a message displays on the multi-information display when there is a malfunction, and do not when there is not a malfunction.

OK:

There are no problems with warning lights or warning messages.


HINT:

The warning notification function of the telematics system uses the warning notification signals sent and received by the meter/gauge system. Therefore, if the meter/gauge system is not operating normally, the warning notification function will not operate normally.



Result:
Proceed to
OK
NG



OK

NG