When the electric parking brake switch assembly is pulled, a lock request signal is sent from the No. 2 skid control ECU (brake actuator assembly) to the parking brake actuator assembly. When the electric parking brake switch assembly is pushed, a release request signal is sent from the No. 2 skid control ECU (brake actuator assembly) to the parking brake actuator assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
|---|---|---|---|---|---|
| C060962 | Electric Parking Brake Switch Signal Compare Failure |
·
Parking brake switch open or short circuit is detected for 1 second or more
·
Parking brake switch stuck malfunction |
·
Electric parking brake switch assembly
·
Wire harness or connector
·
No. 2 skid control ECU (brake actuator assembly) |
DTC stored | An electric parking brake system malfunction is displayed on the multi-information display. |
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
| Diagnosis Condition | - | - | - | - |
| Malfunction Status | Parking brake switch open circuit is detected | ○ | - | - |
| Parking brake switch short circuit is detected | - | ○ | - | |
| Parking brake switch stuck malfunction | - | - | ○ | |
| Detection Time | 1 second or more | 1 second or more | - | |
| Number of Trips | 1 trip | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
When the electric parking brake switch assembly is pulled and held for 1 second or more without being pulled fully to the lock side, both of the 2 linked contacts may turn OFF causing this DTC to be stored (this is not a system malfunction).
To ensure that the electric parking brake does not operate, wait for 4 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.
After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY
When replacing the No. 2 skid control ECU (brake actuator assembly), operate the electric parking brake switch assembly as the parking brake indicator light blinks when the ignition switch is first turned ON.
OK
NG
Disconnect the I184 electric parking brake switch assembly connector.
Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B20,I184)Location & Routingewd_type=routing;type=c,c;code=B20,I184 |
||
| B20-36 (SWI1) - I184-7 (SWI1) | Always | Below 1 Ω |
| B20-31 (SWO1) - I184-8 (SWO1) | Always | Below 1 Ω |
| B20-41 (SWI2) - I184-1 (SWI2) | Always | Below 1 Ω |
| B20-39 (SWO2) - I184-2 (SWO2) | Always | Below 1 Ω |
| B20-36 (SWI1) or I184-7 (SWI1) - Body ground | Always | 10 kΩ or higher |
| B20-31 (SWO1) or I184-8 (SWO1) - Body ground | Always | 10 kΩ or higher |
| B20-41 (SWI2) or I184-1 (SWI2) - Body ground | Always | 10 kΩ or higher |
| B20-39 (SWO2) or I184-2 (SWO2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are output | A |
| DTCs are not output | B |
A
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for RHD)>REMOVAL
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING