Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for RHD) › from 2021.07
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0467251 BRAKE ACTUATOR(for RHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C455213N02
4.125,0.271 4.542,0.271 false 6.698,0.229 6.865,0.229 false 6.698,0.604 6.865,0.604 false 5.479,0.885 5.854,1.594 5.854,1.594 6.021,1.594 true 4.188,2.052 4.635,2.688 4.635,2.688 4.802,2.688 false 1.177,1.375 1.677,1.375 1.677,1.375 1.938,1.177 true 1.438,1.375 1.656,1.198 true 2.906,0.677 3.833,0.677 3.833,0.677 3.906,0.5 true 3.74,0.667 3.813,0.5 true 3.646,0.667 3.719,0.51 true 3.563,0.667 3.635,0.521 true 3.656,3.365 4.25,4.167 4.25,4.167 4.417,4.167 false 1.365,3.781 1.813,3.167 1.813,3.167 1.979,3.167 false 6.177,0.073 6.667,0.448 0.49,0.375 18 false 1, 2 6.458,0.469 6.74,0.823 0.281,0.354 18 false 3 2.042,3.031 2.323,3.385 0.281,0.354 18 false 4 6.333,1.479 6.615,1.833 0.281,0.354 18 false 5 0.698,1.198 1.385,1.75 0.688,0.552 18 false 6, 7 2.625,0.552 3.229,0.927 0.604,0.375 18 false 6 5.031,0.146 5.313,0.5 0.281,0.354 18 false 8 5.146,2.573 5.427,2.927 0.281,0.354 18 false 9 4.719,4.063 5.25,4.438 0.531,0.375 18 false 10 2.365,1.531 2.646,1.885 0.281,0.354 10 false x3 4.667,3.573 4.948,3.927 0.281,0.354 10 false x 2 4.885,0.188 5.167,0.542 0.281,0.354 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 PERFORM ACCUMULATOR PRESSURE ZERO DOWN - (Click here) - -
3 DRAIN BRAKE FLUID - - (Click here) -
4 ENGINE SIDE COVER RH 51473C - - -
5 ENGINE ROOM MAIN WIRE 82111 (Click here) - -
6 DISCONNECT BRAKE TUBE - (Click here) - -
7 REMOVE BRAKE TUBE - (Click here) - -
8 NO. 2 BRAKE TUBE CLAMP 47372 (Click here) - -
9 BRAKE ACTUATOR WITH BRACKET - (Click here) - -
10 NO. 3 BRAKE ACTUATOR BRACKET 44593 (Click here)

● Non-reusable part - -

C455219N04
1.833,3.927 2.417,3.927 false 2,3.083 2,2.719 2,2.719 2.365,2.719 false 5.438,1.896 5.771,1.896 false 3.823,3.615 4.156,3.615 false 1.854,3.094 2.438,3.094 false 2,2.917 3,2.917 true 2.031,3.927 2.031,3.563 2.031,3.563 2.396,3.563 false 2.031,3.75 3.031,3.75 true 3.031,0.938 3.281,0.76 3.281,0.76 3.417,0.76 false 2.854,2.354 3.25,2.135 3.25,2.135 3.385,2.135 false 6.188,1.76 6.854,2.26 0.667,0.5 18 false 11 1.479,3.76 2.146,4.26 0.667,0.5 18 false 12 1.479,2.938 2.146,3.438 0.667,0.5 18 false 13 4.229,3.51 4.646,3.76 0.417,0.25 10 false *1 3.427,2.042 3.844,2.292 0.417,0.25 10 false *3 1.729,0.354 2.146,0.604 0.417,0.25 10 false x 3 3.469,0.667 3.885,0.917 0.417,0.25 10 false *2

Procedure Part Name Code
Z101186

Z101188

Z101187

11 BRAKE ACTUATOR ASSEMBLY 44510 (Click here) - -
12 NO. 1 BRAKE ACTUATOR CASE COLLAR 44521A (Click here) - -
13 BRAKE ACTUATOR BRACKET CUSHION 44547B (Click here) - -

*1 BRAKE ACTUATOR BRACKET ASSEMBLY *2 NO. 1 BRAKE ACTUATOR BRACKET
*3 NO. 2 BRAKE ACTUATOR BRACKET - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake actuator assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
No. 2 skid control ECU (brake actuator assembly) ECU configuration - (Click here)
Update ECU security key Vehicle control history (RoB) are stored (Click here)
1.

Bleed air

2.

Perform "Calibration"


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

Electronically controlled brake system disabled or malfunctions


(Click here)
Operate the electric parking brake switch (electric parking brake switch assembly) Parking brake indicator light blinks when the ignition switch is first turned to ON (Click here)
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -




CAUTION / NOTICE / HINT

NOTICE:

While the battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the battery is connected.


PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click here(Click here)



Hide 2.PERFORM ACCUMULATOR PRESSURE ZERO DOWN

a.
C438176N01
0.479,0.115 0.76,0.469 0.281,0.354 18 false i

i.

Using the GTS, perform the accumulator pressure zero down operation.

1. Select "Motor Deactivate" on the "ECB Utility" screen.

Chassis > Brake/EPB > Utility
Tester Display
ECB Utility
50005 435 2617

2. Perform "Motor Deactivate" according to the display on the GTS.

3. Select "ECB Deactivate" on the "ECB Utility" screen.

Chassis > Brake/EPB > Utility
Tester Display
ECB Utility
50005 435 3617

4. Perform "ECB Deactivate" according to the display on the GTS.

5. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

HINT:

A buzzer may sound due to low accumulator pressure. As this is not a malfunction, continue the procedure.


6. Check that the brake pedal is firm.

NOTICE:

If the brake pedal is not firm or the pump motor continues to operate even after depressing the brake pedal 40 times or more, the accumulator pressure zero down operation is not complete.


7. Disconnect the cable from the negative (-) battery terminal.


CAUTION:
B422343

·

Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.





b.
C455215N02
0.417,0.083 0.833,0.5 0.417,0.417 18 false i

i.

When the accumulator pressure zero down could not be performed using the GTS.

NOTICE:

If DTCs are output, the accumulator pressure zero down operation may not be complete. In this case, perform the following procedure.


1. Remove the engine side cover RH.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL

2. With the ignition switch off, disconnect the brake master cylinder with pump assembly connector.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.


3. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

4. Check that the brake pedal is firm.

NOTICE:

If the brake pedal is not firm or the pump motor continues to operate even after depressing the brake pedal 40 times or more, the accumulator pressure zero down operation is not complete.


5. Disconnect the cable from the negative (-) battery terminal.


CAUTION:
B422343

·

Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.





Hide 3.DRAIN BRAKE FLUID

Z101186

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.



Hide 51473C 4.REMOVE ENGINE SIDE COVER RH

Hide 82111 5.DISCONNECT ENGINE ROOM MAIN WIRE

a.
C455217C02
0.396,0.083 0.615,0.396 0.219,0.313 18 true i 3.854,0.083 4.031,0.417 0.177,0.333 18 true ii
V113147

Release the lock lever
V113148

Disconnect the connector


i.

Disconnect the brake master cylinder with pump assembly connector.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



ii.

Release the lock lever and disconnect the connector from the brake actuator assembly.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.




Hide 6.DISCONNECT BRAKE TUBE

Z101186

NOTICE:
·

Do not kink or damage the brake tubes.

·

Do not allow any foreign matter such as dirt or dust to enter the brake tubes from the connecting parts.




a.
C455221C03
3.792,0.625 4.271,0.344 4.271,0.344 4.438,0.344 true 3.323,0.5 3.073,0.333 3.073,0.333 2.656,0.333 true 2.813,1.042 2.563,1.125 2.563,1.125 2.146,1.125 true 3.094,1.385 2.844,1.573 2.844,1.573 2.51,1.573 true 4.125,1.094 3.792,1.094 3.792,1.094 3.708,0.927 true 3.563,0.521 3.969,0.146 3.969,0.146 4.135,0.146 true 1.938,1.031 2.146,1.198 0.208,0.167 10 false *a 2.25,1.479 2.479,1.656 0.229,0.177 10 true *b 2.427,0.229 2.656,0.406 0.229,0.177 10 true *c 4.135,0.063 4.365,0.229 0.229,0.167 10 true *d 4.469,0.271 4.698,0.458 0.229,0.188 10 true *e 4.156,1.021 4.406,1.188 0.25,0.167 10 true *f 0.396,0.083 0.729,0.5 0.333,0.417 18 false i
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly *b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Wheel Cylinder Assembly RH *d To Front Wheel Cylinder Assembly LH
*e To Rear Wheel Cylinder Assembly RH *f To Rear Wheel Cylinder Assembly LH


i.

Use tags or make a memo to identify the places to reconnect the brake tubes.



b.
C455225N02
0.396,0.083 0.677,0.438 0.281,0.354 18 false i

i.

Using a union nut wrench, disconnect the 6 brake tubes from the brake actuator assembly and brake booster with master cylinder assembly.



Hide 7.REMOVE BRAKE TUBE

a.
C457193N02
0.385,0.125 0.667,0.625 0.281,0.5 18 false i 0.396,2.146 0.677,2.646 0.281,0.5 18 false ii

i.

Using a union nut wrench, disconnect the 2 brake tubes from the brake booster with master cylinder assembly.

NOTICE:
·

Do not kink or damage the brake tubes.

·

Do not allow any foreign matter such as dirt or dust to enter the brake tubes from the connecting parts.




ii.

Disengage the clamps and separate the 2 brake tubes.

NOTICE:

Do not kink or damage the brake tubes.




Hide 47372 8.REMOVE NO. 2 BRAKE TUBE CLAMP

Z101186

NOTICE:

Do not kink or damage the brake tubes.



a.
C457159


Hide 9.REMOVE BRAKE ACTUATOR WITH BRACKET

Z101186

NOTICE:
·

Do not kink or damage the brake tubes.

·

Do not allow any foreign matter such as dirt or dust to enter the brake tubes from the connecting parts.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not hold the brake actuator with bracket by the connector.

·

Do not drop the brake actuator with bracket when carrying it.



HINT:

Remove the brake actuator with bracket while avoiding the brake tubes.



a.
C455229


Hide 44593 10.REMOVE NO. 3 BRAKE ACTUATOR BRACKET

Z101186

HINT:

Perform this procedure only when replacement of the No. 3 brake actuator bracket is necessary.



a.
C455231


Hide 44510 11.REMOVE BRAKE ACTUATOR ASSEMBLY

Z101186

NOTICE:
·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator assembly when carrying it.




a.
C457167


Hide 44521A 12.REMOVE NO. 1 BRAKE ACTUATOR CASE COLLAR

Z101186

HINT:

Perform this procedure only when replacement of the No. 1 brake actuator case collars is necessary.



a.
C455234


Hide 44547B 13.REMOVE BRAKE ACTUATOR BRACKET CUSHION

Z101186

HINT:

Perform this procedure only when replacement of the brake actuator bracket cushions is necessary.



a.
C455236