Home › Engine / Hybrid System › 1VD-FTV (ENGINE MECHANICAL) › CYLINDER HEAD
RM25T0E _51 Engine / Hybrid System _029207 1VD-FTV ENGINE MECHANICAL _0132957 CYLINDER HEAD G

1VD-FTV ENGINE MECHANICAL  CYLINDER HEAD  INSPECTION  


PROCEDURE

Hide 11101 1.CLEAN CYLINDER HEAD SUB-ASSEMBLY

a.

Using a gasket scraper, remove all the gasket material from the cylinder block sub-assembly contact surface.

NOTICE:

Be careful not to scratch the cylinder block sub-assembly contact surface.



b.
A164826

Using a wire brush, remove all the carbon from the combustion chambers.

NOTICE:

Be careful not to damage the combustion chambers and valve seats.



c.
A164841

Using a valve guide bushing brush and solvent, clean all the valve guide bushes.


d.

Using a soft brush and solvent, thoroughly clean the cylinder head sub-assembly.


Hide 11101 2.INSPECT CYLINDER HEAD SUB-ASSEMBLY

a.

Using a precision straightedge and feeler gauge, measure the warpage of the contact surface between the cylinder head sub-assembly and cylinder block sub-assembly, and the cylinder head sub-assembly and manifolds.

Standard Warpage:
Item Specified Condition
Cylinder Block Sub-assembly Side 0 to 0.05 mm (0 to 0.00197 in.)
Intake Manifold Side 0 to 0.08 mm (0 to 0.00315 in.)
Exhaust Manifold Side 0 to 0.08 mm (0 to 0.00315 in.)


Maximum Warpage:
Item Specified Condition
Cylinder Block Sub-assembly Side 0.05 mm (0.00197 in.)
Intake Manifold Side 0.08 mm (0.00315 in.)
Exhaust Manifold Side 0.08 mm (0.00315 in.)


A316798C01
3.917,0.302 4.229,0.458 0.313,0.156 10 false *a 3.917,1.719 4.229,1.875 0.313,0.156 10 false *b 3.917,2.688 4.229,2.844 0.313,0.156 10 false *c
*a Cylinder Block Sub-assembly Side *b Exhaust Manifold Side
*c Intake Manifold Side - -


If the warpage is more than the maximum, replace the cylinder head sub-assembly.


b.

Using a dye penetrant, check the intake ports, exhaust ports and cylinder surface for cracks.

If there are cracks, replace the cylinder head sub-assembly.


Hide 13711B 3.INSPECT INNER COMPRESSION SPRING

a.

Inspect the inner compression spring deviation.

i.
A101393C13
1.26,0.104 1.573,0.26 0.313,0.156 10 false *a
*a Deviation


Using a steel square, measure the deviation of the inner compression spring.

Maximum deviation:

1.5 mm (0.0591 in.)


If the deviation is more than the maximum, replace the inner compression spring.



b.

Inspect the inner compression spring free length.

i.
A101392

Using a vernier caliper, measure the free length of the inner compression spring.

Standard free length:

45.9 mm (1.81 in.)


If the free length is not as specified, replace the inner compression spring.



c.

Inspect the inner compression spring tension.

i.
EM00281

Using a spring tester, measure the tension of the inner compression spring at the specified installed length.

Installed tension:

219 to 242 N (22 to 25 kgf, 49.2 to 54.4 lbf) at 31.0 mm (1.22 in.)


If the installed tension is not as specified, replace the inner compression spring.



Hide 13711 4.CLEAN VALVE

a.

Using a gasket scraper, chip off any carbon from the valve head.

NOTICE:

Be careful not to damage the valve seats.



b.

Using a wire brush, thoroughly clean the valve.


Hide 13711 5.INSPECT VALVE

a.

Inspect the valve stem diameter.

i.

Using a micrometer, measure the diameter of the valve stem.

Standard Valve Stem Diameter:
Item Specified Condition
Intake 5.970 to 5.985 mm (0.2350 to 0.2356 in.)
Exhaust 5.960 to 5.975 mm (0.2346 to 0.2352 in.)




b.

Inspect the valve face angle.

i.
A075611N01
2.969,1.531 3.427,1.729 0.458,0.198 10 false 45.5°

Grind the valve enough to remove pits and carbon.


ii.

Check that the valve is ground to the correct valve face angle.

Standard valve face angle:

45.5°




c.

Inspect the valve head margin thickness.

i.
A131998C03
0.458,1.698 0.771,1.854 0.313,0.156 10 false *a
*a Margin Thickness


Using a vernier caliper, measure the valve head margin thickness.

Standard margin thickness:

1.0 mm (0.0394 in.)


Minimum margin thickness:

0.5 mm (0.0197 in.)


If the margin thickness is less than the minimum, replace the valve.



d.

Inspect the valve overall length.

i.

Using a vernier caliper, measure the overall length.

Standard Overall Length:
Item Specified Condition
Intake 104.4 mm (4.11 in.)
Exhaust 104.1 mm (4.10 in.)


Minimum Overall Length:
Item Specified Condition
Intake 104.1 mm (4.10 in.)
Exhaust 103.8 mm (4.09 in.)


If the overall length is less than the minimum, replace the valve.



e.

Inspect the valve stem tip.

i.

Check the surface of the valve stem tip for wear.

NOTICE:

Do not grind the valve so it becomes shorter than the minimum overall length.


If the valve stem tip is worn, resurface the tip with a grinder or replace the valve.



Hide 11122 6.INSPECT VALVE GUIDE BUSH OIL CLEARANCE

a.
A164580

Using a caliper gauge, measure the inside diameter of the valve guide bush.

Standard valve guide bush inside diameter:

6.01 to 6.03 mm (0.2366 to 0.2374 in.)



b.

Subtract the valve stem diameter measurement from the valve guide bush inside diameter measurement.

Standard Oil Clearance:
Item Specified Condition
Intake 0.025 to 0.060 mm (0.000984 to 0.00236 in.)
Exhaust 0.035 to 0.070 mm (0.00138 to 0.00276 in.)


Maximum Oil Clearance:
Item Specified Condition
Intake 0.120 mm (0.00472 in.)
Exhaust 0.130 mm (0.00512 in.)


If the oil clearance is more than the maximum, replace the valve guide bush.


Hide 7.CLEAN VALVE SEAT

a.

Using a 45° carbide cutter, resurface the valve seats.

NOTICE:

Be careful not to damage the combustion chambers and valve seats.



b.

Clean the valve seats.


Hide 8.INSPECT INTAKE VALVE SEAT

a.
A164578C01
1.396,1.385 1.708,1.542 0.313,0.156 10 false *a
*a Width


Apply a light coat of Prussian blue to the intake valve face.


b.

Lightly press the intake valve face against the intake valve seat.

NOTICE:

Do not rotate the intake valve while pressing the intake valve.



c.

Check the intake valve face and intake valve seat.

i.

Check that the contact surfaces of the intake valve seat and intake valve face are in the middle area of their respective surfaces, with the width between 1.0 to 1.4 mm (0.0394 to 0.0551 in.).

If not, correct the intake valve seat.


ii.

Check that the contact surfaces of the intake valve seat and intake valve face are even around the entire intake valve seat.

If not, correct the intake valve seat.



Hide 9.INSPECT EXHAUST VALVE SEAT

a.
A164579C01
1.385,1.385 1.698,1.542 0.313,0.156 10 false *a
*a Width


Apply a light coat of Prussian blue to the exhaust valve face.


b.

Lightly press the exhaust valve face against the exhaust valve seat.

NOTICE:

Do not rotate the exhaust valve while pressing the exhaust valve.



c.

Check the exhaust valve face and exhaust valve seat.

i.

Check that the contact surfaces of the exhaust valve seat and exhaust valve face are in the middle area of their respective surfaces, with the width between 1.0 to 1.4 mm (0.0394 to 0.0551 in.).

If not, correct the exhaust valve seat.


ii.

Check that the contact surfaces of the exhaust valve seat and exhaust valve face are even around the entire exhaust valve seat.

If not, correct the exhaust valve seat.



Hide 13512 10.INSPECT NO. 2 AND NO. 3 CAMSHAFT THRUST CLEARANCE (for Intake Camshaft)

a.

Install the No. 2 and No. 5 camshaft bearing caps to the cylinder head sub-assembly.


b.

Place the No. 2 and No. 3 camshaft on the cylinder head sub-assembly.


c.
A164896

Temporarily install the No. 1 and No. 4 camshaft bearing caps with the 4 bolts by hand.

NOTICE:

Do not turn the No. 2 and No. 3 camshaft.



d.

Install the No. 3 camshaft bearing caps.

i.
A164898C01
0.125,0.021 0.438,0.177 0.313,0.156 10 false *A 0.115,2.813 0.427,2.969 0.313,0.156 10 false *B
*A for Bank 1
*B for Bank 2


Confirm the marks and numbers on the No. 3 camshaft bearing caps and place them in their proper position and direction.


ii.

Temporarily install the 16 bolts.



e.
A164897C01
0.052,0.042 0.365,0.198 0.313,0.156 10 false *A 0.052,2.323 0.365,2.479 0.313,0.156 10 false *B 1.479,0.833 1.615,1.01 0.135,0.177 10 true 1 1.49,1.938 1.74,2.115 0.25,0.177 10 false 2 2.094,0.854 2.24,1.021 0.146,0.167 10 true 3 2.083,1.927 2.313,2.198 0.229,0.271 10 false 4 0.896,0.823 1.052,1.01 0.156,0.188 10 true 5 0.896,1.927 1.125,2.198 0.229,0.271 10 false 6 2.698,0.844 2.875,1.031 0.177,0.188 10 true 7 2.698,1.938 2.927,2.208 0.229,0.271 10 false 8 0.229,1.469 0.365,1.646 0.135,0.177 10 true 9 0.271,1.958 0.5,2.135 0.229,0.177 10 false 10 0.198,0.688 0.427,0.958 0.229,0.271 10 false 11 0.25,0.271 0.469,0.469 0.219,0.198 10 false 12 0.156,4.208 0.375,4.406 0.219,0.198 10 false 12 0.125,3.781 0.354,4.052 0.229,0.271 10 false 11 0.135,3.042 0.271,3.219 0.135,0.177 10 true 9 0.146,2.563 0.375,2.74 0.229,0.177 10 false 10 0.99,3.635 1.146,3.823 0.156,0.188 10 true 5 1.583,3.646 1.719,3.823 0.135,0.177 10 true 1 2.198,3.635 2.344,3.802 0.146,0.167 10 true 3 2.802,3.646 2.979,3.833 0.177,0.188 10 true 7 0.99,2.573 1.219,2.844 0.229,0.271 10 false 6 1.583,2.573 1.833,2.75 0.25,0.177 10 false 2 2.198,2.573 2.427,2.844 0.229,0.271 10 false 4 2.792,2.573 3.021,2.844 0.229,0.271 10 false 8
*A for Bank 1
*B for Bank 2


Uniformly tighten the 24 bolts in several steps in the order shown in the illustration.

Torque:
for 12 mm head bolt of No. 1 and No. 4 camshaft bearing cap : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for 10 mm head bolt of No. 3 camshaft bearing cap : 10 N*m (102 kgf*cm, 7 ft.*lbf)


f.
A164551

Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

Standard thrust clearance:

0.035 to 0.160 mm (0.00138 to 0.00630 in.)


Maximum thrust clearance:

0.180 mm (0.00709 in.)


If the thrust clearance is more than the maximum, replace the No. 2 and No. 3 camshaft.

If necessary, replace the cylinder head sub-assembly.


Hide 13511 11.INSPECT NO. 1 AND NO. 4 CAMSHAFT THRUST CLEARANCE (for Exhaust Camshaft)

a.

Install the No. 2 and No. 5 camshaft bearing caps to the cylinder head sub-assembly.


b.

Place the No. 1 and No. 4 camshaft on the cylinder head sub-assembly.


c.
A164958

Temporarily install the No. 1 and No. 4 camshaft bearing caps with the 4 bolts by hand.

NOTICE:

Do not turn the No. 1 and No. 4 camshaft.



d.

Install the No. 3 camshaft bearing caps.

i.
A164959C01
0.177,0.552 0.49,0.708 0.313,0.156 10 false *A 0.177,2.198 0.49,2.354 0.313,0.156 10 false *B
*A for Bank 1
*B for Bank 2


Confirm the marks and numbers on the No. 3 camshaft bearing caps and place them in their proper position and direction.


ii.

Temporarily install the 16 bolts.



e.
A164947C01
0.094,0.219 0.406,0.375 0.313,0.156 10 false *A 1.49,1.49 1.625,1.667 0.135,0.177 10 true 1 1.479,0.448 1.615,0.615 0.135,0.167 10 true 2 2.104,1.479 2.25,1.646 0.146,0.167 10 true 3 2.083,0.458 2.198,0.615 0.115,0.156 10 true 4 0.906,1.469 1.052,1.635 0.146,0.167 10 true 5 0.885,0.438 1.01,0.594 0.125,0.156 10 true 6 2.688,1.49 2.813,1.667 0.125,0.177 10 true 7 2.688,0.448 2.823,0.625 0.135,0.177 10 true 8 0.24,0.927 0.365,1.104 0.125,0.177 10 true 9 0.344,0.417 0.656,0.573 0.313,0.156 10 false 10 0.229,1.625 0.542,1.781 0.313,0.156 10 false 11 0.344,2.073 0.656,2.229 0.313,0.156 10 false 12 0.146,2.552 0.458,2.708 0.313,0.156 10 false 12 0.115,3.031 0.427,3.188 0.313,0.156 10 false 11 0.167,3.615 0.292,3.792 0.125,0.177 10 true 9 0.24,4.198 0.552,4.354 0.313,0.156 10 false 10 1.052,4.156 1.177,4.313 0.125,0.156 10 true 6 1.635,4.177 1.771,4.344 0.135,0.167 10 true 2 2.219,4.167 2.333,4.323 0.115,0.156 10 true 4 2.802,4.177 2.938,4.354 0.135,0.177 10 true 8 2.792,3.104 2.917,3.281 0.125,0.177 10 true 7 2.219,3.125 2.365,3.292 0.146,0.167 10 true 3 1.615,3.094 1.75,3.271 0.135,0.177 10 true 1 1.063,3.104 1.208,3.271 0.146,0.167 10 true 5 0.104,2.344 0.417,2.5 0.313,0.156 10 false *B
*A for Bank 1
*B for Bank 2


Uniformly tighten the 24 bolts in several steps in the order shown in the illustration.

Torque:
for 12 mm head bolt of No. 1 and No. 4 camshaft bearing cap : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for 10 mm head bolt of No. 3 camshaft bearing cap : 10 N*m (102 kgf*cm, 7 ft.*lbf)


f.
A164550

Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

Standard thrust clearance:

0.035 to 0.160 mm (0.00138 to 0.00630 in.)


Maximum thrust clearance:

0.180 mm (0.00709 in.)


If the thrust clearance is more than the maximum, replace the No. 1 and No. 4 camshaft.

If necessary, replace the cylinder head sub-assembly.


Hide 13511 12.INSPECT CAMSHAFT OIL CLEARANCE