Home › Engine / Hybrid System › 1HZ (LUBRICATION) › OIL AND OIL FILTER › 2014.08–2021.07
RM25T0E _51 Engine / Hybrid System _029209 1HZ LUBRICATION _0133936 OIL AND OIL FILTER A

1HZ LUBRICATION  OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

·

Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners or solvents.

·

In order to protect the environment, used oil and used oil filter sub-assemblies must be disposed of at designated disposal sites.



PROCEDURE

Hide 1.DRAIN ENGINE OIL

a.

Remove the oil filler cap sub-assembly.


b.

Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.


c.

Wipe the oil pan sub-assembly and oil pan drain plug.


d.

Install a new gasket and the oil pan drain plug.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)


Hide 15601 2.REMOVE OIL FILTER SUB-ASSEMBLY

a.
A326397N01
0.583,0.167 0.75,0.167 0.75,0.167 1.583,0.833 true 0.302,0.073 0.76,0.271 0.458,0.198 10 false SST

Using SST, remove the oil filter sub-assembly.

SST
09228-10002  


Hide 15601 3.INSTALL OIL FILTER SUB-ASSEMBLY

a.

Check and clean the oil filter sub-assembly installation surface.


b.

Apply clean engine oil to the gasket of a new oil filter sub-assembly.


c.

Lightly screw the oil filter sub-assembly into place by hand. Tighten it until the gasket contacts the seat.


d.
A326398N01
0.5,0.917 1.333,0.917 true 0.208,0.823 0.667,1.021 0.458,0.198 10 false SST

Using SST, tighten the oil filter sub-assembly. Depending on the space available, choose from the following.

SST
09228-10002  

i.

If enough space is available, use a torque wrench to tighten the oil filter sub-assembly.

Torque:
17.6 N*m (179 kgf*cm, 13 ft.*lbf)


ii.

If enough space is not available to use a torque wrench, tighten the oil filter sub-assembly 3/4 of a turn by hand or with a common wrench.



Hide 4.ADD ENGINE OIL

a.

Add new engine oil.

Standard Oil Grade:
Oil Grade Oil Viscosity (SAE)
API CF-4, CF or ACEA B1 - 5W-30
- 10W-30
- 15W-40
- 20W-50


Standard Capacity:
Item Specified Condition
Drain and refill without oil filter sub-assembly change 10.0 liters (10.6 US qts, 8.8 Imp. qts)
Drain and refill with oil filter sub-assembly change 11.3 liters (11.9 US qts, 9.9 Imp. qts)
Dry fill 11.6 liters (12.3 US qts, 10.2 Imp. qts)



b.

Install the oil filler cap sub-assembly.


Hide 5.INSPECT FOR OIL LEAK

a.

Start the engine. Make sure that there are no oil leaks from the areas that were worked on.