Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and stores the DTC.

HINT:

The normal conditions are as shown in the table below. The signals can be read using the GTS.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the GTS, both the Data List items Stop Light Switch and ST1 are ON when the brake pedalis depressed because the ST1 indication characteristic is opposite to the Stop Light Switch indication.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0504 Brake Switch "A" / "B" Correlation Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic):
(a) The ignition switch is ON.
(b) The brake pedal is released.
(c) The STP signal is OFF when the ST1- signal is OFF.
·

Short in stop light switch signal circuit

·

Stop light switch assembly

·

ECM


- DTC stored

WIRING DIAGRAM

A222283E03
0.573,0.885 1.865,1.052 1.292,0.167 10 false from Ignition Switch 1.01,1.875 1.896,2.083 0.885,0.208 10 false from Battery 2.448,1.073 2.76,1.229 0.313,0.156 10 false IGN 4.219,1.802 4.354,1.958 0.135,0.156 10 false 1 5.729,2.948 6.656,3.188 0.927,0.24 10 false A84*1, A29 *2 5.896,3.104 6.281,3.26 0.385,0.156 10 false ECM 3.094,1.802 3.229,1.958 0.135,0.156 10 false 2 4.219,0.813 4.354,0.969 0.135,0.156 10 false 4 5.313,0.813 5.51,0.969 0.198,0.156 10 false 35 5.313,1.802 5.51,1.958 0.198,0.156 10 false 36 5.594,0.813 5.938,0.969 0.344,0.156 10 false ST1- 5.594,1.802 5.938,1.958 0.344,0.156 10 false STP 3.094,0.813 3.229,0.969 0.135,0.156 10 false 3 4.656,2.063 5.063,2.219 0.406,0.156 10 false STOP 2.406,2.063 2.813,2.219 0.406,0.156 10 false STOP 3.135,2.24 3.458,2.385 0.323,0.146 10 false I19 3.135,2.396 4.25,2.844 1.115,0.448 10 false Stop Light Switch Assembly 4.24,2.823 5.313,3.021 1.073,0.198 10 false *1: for LHD 4.26,3.094 5.177,3.292 0.917,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

STP signal conditions can be checked using the GTS.

(a)

Connect the GTS to the DLC3.

(b)

Turn the ignition switch to ON.

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.

(e)

Check the STP signal when the brake pedal is depressed and released.




Brake Pedal Operation Specified Condition
Depressed STP signal ON
Released STP signal OFF

PROCEDURE

1.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE)
a.
A148738C17
1.552,0.854 1.917,1.094 0.365,0.24 0.177,0.177 0.469,0.406 0.292,0.229 10 false *a 1.604,0.896 1.875,1.042 0.271,0.146 10 false I19
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I19-2 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY)

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
a.
A148738C17
1.552,0.854 1.917,1.094 0.365,0.24 0.177,0.177 0.469,0.406 0.292,0.229 10 false *a 1.604,0.896 1.875,1.042 0.271,0.146 10 false I19
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I19-3 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - IGNITION SWITCH)

3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.


Result:
Proceed to
OK
NG



OK

4.CHECK ECM (STP AND ST1- VOLTAGE)

NG

REPLACE STOP LAMP SWITCH ASSEMBLY

4.CHECK ECM (STP AND ST1- VOLTAGE)
a.

Disconnect the ECM connector.


b.
A112585C07
0.823,2.594 1.25,2.833 0.427,0.24 1.76,2.594 2.188,2.844 0.427,0.25 1.865,3.667 2.625,3.406 true 1.771,3.667 2.563,4.375 true 0.188,0.573 0.5,0.802 0.313,0.229 10 false *a 2.698,3.333 3.354,3.563 0.656,0.229 10 false 36 (STP) 2.635,4.302 3.323,4.563 0.688,0.26 10 false 35 (ST1-) 0.906,2.635 1.198,2.813 0.292,0.177 10 false I84 1.667,0.583 1.979,0.813 0.313,0.229 10 false *b 0.5,2.323 0.813,2.552 0.313,0.229 10 false *c 1.875,2.646 2.333,2.844 0.458,0.198 10 false A29 1.26,2.49 1.573,2.688 0.313,0.198 10 false *A 2.25,2.51 2.563,2.708 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Front view of wire harness connector
(to ECM)


Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Brake Pedal Operation Specified Condition
I84-35 (ST1-) - Body ground Released 11 to 14 V
Depressed Below 1.5 V
I84-36 (STP) - Body ground Released Below 1.5 V
Depressed 11 to 14 V

for RHD
Tester Connection Brake Pedal Operation Specified Condition
A29-35 (ST1-) - Body ground Released 11 to 14 V
Depressed Below 1.5 V
A29-36 (STP) - Body ground Released Below 1.5 V
Depressed 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR