Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0115  Engine Coolant Temperature Circuit Malfunction  P0117  Engine Coolant Temperature Circuit Low Input  P0118  Engine Coolant Temperature Circuit High Input  


DESCRIPTION

A thermistor, whose resistance value varies according to the Engine Coolant Temperature (ECT), is built into the Engine Coolant Temperature (ECT) sensor.

The structure of the sensor and its connection to the ECM are the same as those of the Intake Air Temperature (IAT) sensor.

HINT:

When any of DTCs P0115, P0117 and P0118 are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECT is estimated to be 80°C (176°F) by the ECM. Fail-safe mode continues until a pass condition is detected.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0115 Engine Coolant Temperature Circuit Malfunction An open or short in the Engine Coolant Temperature (ECT) sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open or short in Engine Coolant Temperature (ECT) sensor circuit

·

ECT sensor

·

ECM


Comes on DTC stored
P0117 Engine Coolant Temperature Circuit Low Input A short in the ECT sensor circuit for 0.5 seconds (1 trip detection logic).
·

Short in ECT sensor

·

ECT sensor

·

ECM


Comes on DTC stored
P0118 Engine Coolant Temperature Circuit High Input An open in the ECT sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open in ECT sensor circuit

·

ECT sensor

·

ECM


Comes on DTC stored

HINT:

When any of these DTCs are output, check the ECT by entering the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


GTS Display Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or higher Short circuit

MONITOR DESCRIPTION

The Engine Coolant Temperature (ECT) sensor is used to monitor the ECT. The ECT sensor has a thermistor with a resistance that varies according to the temperature of the engine coolant. When the coolant temperature is low, the resistance in the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are reflected in the output voltage from the sensor. The ECM monitors the sensor voltage and uses this value to calculate the ECT. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a fault in the ECT sensor and stores a DTC.

Example:

If the sensor output voltage is higher than 4.91 V for 0.5 seconds or more, the ECM determines that there is an open in the ECT sensor circuit, and stores DTC P0118. Conversely, if the voltage output is below 0.14 V for 0.5 seconds or more, the ECM determines that there is a short in the sensor circuit, and stores DTC P0117.

If the malfunction is not repaired successfully, a DTC is stored 0.5 seconds after the engine is next started.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait 0.5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0115, P0117 or P0118.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again




WIRING DIAGRAM

A147856E27
2.604,1.021 2.74,1.177 0.135,0.156 10 false 2 2.604,1.719 2.74,1.875 0.135,0.156 10 false 1 5.375,1.021 5.75,1.177 0.375,0.156 10 false THW 5.375,1.719 5.865,1.875 0.49,0.156 10 false ETHW 5.094,1.021 5.292,1.177 0.198,0.156 10 false 79 5.104,1.719 5.302,1.875 0.198,0.156 10 false 78 1.5,2.208 1.813,2.365 0.313,0.156 10 false C1 1.5,2.385 3.854,2.542 2.354,0.156 10 false Engine Coolant Temperature Sensor 6.021,0.646 6.281,0.792 0.26,0.146 10 false 5 V 5.427,2.354 5.771,2.51 0.344,0.156 10 false C39 5.427,2.521 5.844,2.677 0.417,0.156 10 false ECM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 234 8

e.

Read the value displayed on the GTS.

Standard value:

Between 75 and 100°C (167 and 212°F) with warm engine.


Result:
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
Between 80°C and 100°C (176°F and 212°F) with warm engine C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F) or higher.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A208643C20
0.625,2.656 0.99,2.948 0.365,0.292 0.667,0.396 0.979,0.594 0.313,0.198 10 false *1 2.573,0.271 2.823,0.479 0.25,0.208 10 false *2 0.167,2.146 0.479,2.344 0.313,0.198 10 false *a 0.688,2.708 1,2.906 0.313,0.198 10 false C1 2.51,1.021 2.969,1.219 0.458,0.198 10 false THW 2.458,1.469 2.917,1.667 0.458,0.198 10 false ETHW
*1 Engine Coolant Temperature Sensor
*2 ECM
*a Front view of wire harness connector
(to Engine Coolant Temperature Sensor)


Disconnect the engine coolant temperature sensor connector.


b.

Connect terminals 1 and 2 of the engine coolant temperature sensor connector on the wire harness side.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 234 8

g.

Read the value displayed on the GTS.

Standard value:

140°C (284°F) or higher



Result:
Proceed to
OK
NG



OK

CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR

NG

3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C1-2 - C39-79 (THW) Always Below 1 Ω
C1-1 - C39-78 (ETHW) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
A255925C06
0.662,0.158 0.817,0.312 0.155,0.154 10 *1 2.57,0.158 2.725,0.312 0.155,0.154 10 *2 2.226,0.805 2.566,0.958 0.34,0.154 10 THW 2.226,1.183 2.657,1.337 0.431,0.154 10 ETHW
*1 Engine Coolant Temperature Sensor
*2 ECM


a.

Disconnect the engine coolant temperature sensor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 234 8

f.

Read the value displayed on the GTS.

Standard value:

-40°C (-40°F)



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C1-2 or C39-79 (THW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR