Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0351  Ignition Coil "A" Primary / Secondary Circuit  P0352  Ignition Coil "B" Primary / Secondary Circuit  P0353  Ignition Coil "C" Primary / Secondary Circuit  P0354  Ignition Coil "D" Primary / Secondary Circuit  P0355  Ignition Coil "E" Primary / Secondary Circuit  P0356  Ignition Coil "F" Primary / Secondary Circuit  


DESCRIPTION

HINT:
·

These DTCs indicate malfunctions relating to the primary circuit.

·

If DTC P0351 is output, check the No. 1 ignition coil circuit.

·

If DTC P0352 is output, check the No. 2 ignition coil circuit.

·

If DTC P0353 is output, check the No. 3 ignition coil circuit.

·

If DTC P0354 is output, check the No. 4 ignition coil circuit.

·

If DTC P0355 is output, check the No. 5 ignition coil circuit.

·

If DTC P0356 is output, check the No. 6 ignition coil circuit.



A Direct Ignition System (DIS) is used on this vehicle.

The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil, and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The sparks of the spark plugs pass from the center electrode to the ground electrodes.

The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.

A209715E07
3.323,8 3.677,8.167 0.354,0.167 10 false ECM 0.333,2.031 2.052,2.198 1.719,0.167 10 false Crankshaft Position Sensor 0.771,4.083 1.563,4.25 0.792,0.167 10 false VVT Sensor 0.229,5.656 2.115,6.396 1.885,0.74 10 false Other Sensors (Engine Coolant Temperature Sensor, Mass Air Flow Meter, Throttle Position Sensor, etc.) 3.177,1.563 3.563,1.75 0.385,0.188 10 false IGT1 3.229,2 3.615,2.188 0.385,0.188 10 false IGF 3.177,2.927 3.563,3.115 0.385,0.188 10 false IGT2 3.177,4.01 3.563,4.198 0.385,0.188 10 false IGT3 3.177,5.083 3.563,5.271 0.385,0.188 10 false IGT4 3.177,6.167 3.563,6.354 0.385,0.188 10 false IGT5 3.177,7.25 3.563,7.438 0.385,0.188 10 false IGT6 5.302,0.969 6.167,1.167 0.865,0.198 10 false from Battery 5.698,1.313 6.865,1.51 1.167,0.198 10 false No. 1 Ignition Coil 4.458,2.906 5.625,3.094 1.167,0.188 10 false No. 2 Ignition Coil 5.771,2.115 6.854,2.313 1.083,0.198 10 false No. 1 Spark Plug 5.771,3.302 6.854,3.5 1.083,0.198 10 false No. 2 Spark Plug 4.458,3.99 5.625,4.177 1.167,0.188 10 false No. 3 Ignition Coil 5.771,4.385 6.854,4.583 1.083,0.198 10 false No. 3 Spark Plug 4.458,5.073 5.625,5.25 1.167,0.177 10 false No. 4 Ignition Coil 5.771,5.479 6.854,5.677 1.083,0.198 10 false No. 4 Spark Plug 4.458,6.156 5.625,6.344 1.167,0.188 10 false No. 5 Ignition Coil 5.771,6.542 6.854,6.74 1.083,0.198 10 false No. 5 Spark Plug 4.458,7.229 5.625,7.417 1.167,0.188 10 false No. 6 Ignition Coil 5.771,7.646 6.854,7.844 1.083,0.198 10 false No. 6 Spark Plug 3.01,7.74 3.417,7.906 0.406,0.167 10 false TACH 1.479,8.219 2.031,8.417 0.552,0.198 10 false to DLC3

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0351 Ignition Coil "A" Primary / Secondary Circuit No IGF signal is sent to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF or IGT1 circuit between ignition coil and ECM

·

No. 1 ignition coil

·

ECM


Comes on DTC stored
P0352 Ignition Coil "B" Primary / Secondary Circuit No IGF signal is sent to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF or IGT2 circuit between ignition coil and ECM

·

No. 2 ignition coil

·

ECM


Comes on DTC stored
P0353 Ignition Coil "C" Primary / Secondary Circuit No IGF signal is sent to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF or IGT3 circuit between ignition coil and ECM

·

No. 3 ignition coil

·

ECM


Comes on DTC stored
P0354 Ignition Coil "D" Primary / Secondary Circuit No IGF signal is sent to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF or IGT4 circuit between ignition coil and ECM

·

No. 4 ignition coil

·

ECM


Comes on DTC stored
P0355 Ignition Coil "E" Primary / Secondary Circuit No IGF signal is sent to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF or IGT5 circuit between ignition coil and ECM

·

No. 5 ignition coil

·

ECM


Comes on DTC stored
P0356 Ignition Coil "F" Primary / Secondary Circuit No IGF signal is sent to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF or IGT6 circuit between ignition coil and ECM

·

No. 6 ignition coil

·

ECM


Comes on DTC stored

A112406E01
0.45,0.258 2.451,0.434 2.001,0.176 10 IGT and IGF Signal Waveform 1.064,2.613 1.968,2.789 0.904,0.176 10 20 msec./DIV. 2.713,0.733 3.251,0.917 0.539,0.184 10 2 V/DIV. 2.919,1.592 3.263,1.776 0.344,0.184 10 GND 0.242,1.369 0.512,1.553 0.27,0.184 10 IGT 0.242,2.073 0.502,2.257 0.261,0.184 10 IGF 2.919,2.4 3.263,2.584 0.344,0.184 10 GND


Reference: Inspection using an oscilloscope.

While cranking or idling the engine, check the waveform between terminals IGT (1 to 6) and E1, and IGF and E1 of the ECM connector.

Item Content
Terminal CH1: IGT1, IGT2, IGT3, IGT4, IGT5, IGT6 - E1
CH2: IGF - E1
Equipment Setting 2 V/DIV.
20 msec./DIV.
Condition Idling


MONITOR DESCRIPTION

A220081E04
4.716,2.416 5.484,2.6 0.767,0.184 10 Ignition Coil 4.118,1.542 4.781,1.726 0.663,0.184 10 Igniter 5.33,1.367 6.278,1.53 0.948,0.163 10 Ignition Coil 0.324,2.902 1.458,3.266 1.134,0.365 10 Ignition Signal (IGT) 0.331,3.624 1.171,4.171 0.84,0.547 10 Ignition Confirmation Signal (IGF) 1.61,3.511 2.169,3.688 0.559,0.177 10 Normal 1.386,3.896 2.167,4.073 0.781,0.177 10 Malfunction 3.66,4.52 4.608,4.707 0.948,0.188 10 Circuit Open 5.825,4.984 6.349,5.148 0.524,0.163 10 Time 1.805,1.668 2.204,1.844 0.399,0.175 10 ECM 2.918,1.337 3.245,1.523 0.327,0.186 10 IGT 2.918,1.751 3.245,1.937 0.327,0.186 10 IGF

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.

If the malfunction is not repaired successfully, a DTC is stored 1 second after the engine is next started.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Idle the engine for 10 seconds or more [A].

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0351, P0352, P0353, P0354, P0355 or P0356.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.




WIRING DIAGRAM

A221924E02
0.396,7.948 1.167,8.135 0.771,0.188 10 false Noise Filter 0.396,7.792 0.677,7.958 0.281,0.167 10 false C10 3.135,1.708 4.302,1.875 1.167,0.167 10 false No. 1 Ignition Coil 3.135,2.958 4.302,3.125 1.167,0.167 10 false No. 2 Ignition Coil 3.135,4.219 4.302,4.385 1.167,0.167 10 false No. 3 Ignition Coil 3.135,5.521 4.302,5.688 1.167,0.167 10 false No. 4 Ignition Coil 3.135,8.281 4.302,8.448 1.167,0.167 10 false No. 6 Ignition Coil 3.135,6.781 4.302,6.948 1.167,0.167 10 false No. 5 Ignition Coil 0.073,1.625 1.385,1.813 1.313,0.188 10 false from Ignition Switch 3.125,2.823 3.417,2.969 0.292,0.146 10 false C14 3.125,1.563 3.417,1.708 0.292,0.146 10 false C5 0.813,1.073 1.052,1.219 0.24,0.146 10 false INJ 3.125,4.063 3.417,4.208 0.292,0.146 10 false C6 3.125,5.385 3.417,5.531 0.292,0.146 10 false C13 3.125,6.646 3.417,6.792 0.292,0.146 10 false C7 3.125,8.156 3.417,8.302 0.292,0.146 10 false C12 3.229,0.927 3.469,1.073 0.24,0.146 10 false +B 3.219,1.271 3.552,1.438 0.333,0.167 10 false GND 3.823,1.281 4.083,1.427 0.26,0.146 10 false IGF 3.76,0.917 4.094,1.073 0.333,0.156 10 false IGT1 3.229,2.208 3.469,2.354 0.24,0.146 10 false +B 3.219,2.563 3.552,2.729 0.333,0.167 10 false GND 3.823,2.563 4.083,2.708 0.26,0.146 10 false IGF 5.563,7.719 5.896,7.865 0.333,0.146 10 false IGF 3.75,2.198 4.083,2.354 0.333,0.156 10 false IGT2 3.229,3.458 3.469,3.604 0.24,0.146 10 false +B 3.219,3.792 3.552,3.958 0.333,0.167 10 false GND 3.823,3.792 4.083,3.938 0.26,0.146 10 false IGF 3.75,3.448 4.083,3.604 0.333,0.156 10 false IGT3 3.229,4.708 3.469,4.865 0.24,0.156 10 false +B 3.219,5.052 3.552,5.219 0.333,0.167 10 false GND 3.823,5.052 4.083,5.198 0.26,0.146 10 false IGF 3.75,4.698 4.083,4.854 0.333,0.156 10 false IGT4 3.229,6.01 3.469,6.156 0.24,0.146 10 false +B 3.219,6.365 3.552,6.531 0.333,0.167 10 false GND 3.823,6.365 4.083,6.51 0.26,0.146 10 false IGF 3.75,6.01 4.083,6.167 0.333,0.156 10 false IGT5 3.229,7.281 3.469,7.427 0.24,0.146 10 false +B 3.219,7.833 3.552,8 0.333,0.167 10 false GND 3.823,7.833 4.083,7.979 0.26,0.146 10 false IGF 3.75,7.271 4.083,7.427 0.333,0.156 10 false IGT6 5.563,0.844 5.896,1 0.333,0.156 10 false IGT1 5.563,2.125 5.896,2.281 0.333,0.156 10 false IGT2 5.563,3.365 5.896,3.521 0.333,0.156 10 false IGT3 5.563,4.646 5.896,4.802 0.333,0.156 10 false IGT4 5.563,5.927 5.896,6.083 0.333,0.156 10 false IGT5 5.563,7.198 5.896,7.354 0.333,0.156 10 false IGT6 5.792,8.396 6.146,8.563 0.354,0.167 10 false ECM 5.792,8.24 6.146,8.406 0.354,0.167 10 false C39 3.042,0.844 3.146,1.01 0.104,0.167 10 false 1 4.146,0.854 4.26,1.021 0.115,0.167 10 false 3 3.052,1.198 3.156,1.365 0.104,0.167 10 false 4 4.156,1.188 4.281,1.354 0.125,0.167 10 false 2 3.042,2.115 3.146,2.281 0.104,0.167 10 false 1 4.146,2.125 4.26,2.292 0.115,0.167 10 false 3 3.052,2.469 3.156,2.635 0.104,0.167 10 false 4 4.156,2.458 4.281,2.625 0.125,0.167 10 false 2 3.042,3.365 3.146,3.531 0.104,0.167 10 false 1 4.146,3.365 4.26,3.531 0.115,0.167 10 false 3 3.052,3.719 3.156,3.885 0.104,0.167 10 false 4 4.156,3.708 4.281,3.875 0.125,0.167 10 false 2 3.042,4.625 3.146,4.792 0.104,0.167 10 false 1 4.146,4.635 4.26,4.802 0.115,0.167 10 false 3 3.052,4.979 3.156,5.146 0.104,0.167 10 false 4 4.156,4.979 4.281,5.146 0.125,0.167 10 false 2 3.042,5.927 3.146,6.094 0.104,0.167 10 false 1 4.146,5.927 4.26,6.094 0.115,0.167 10 false 3 3.052,6.281 3.156,6.448 0.104,0.167 10 false 4 4.156,6.271 4.281,6.438 0.125,0.167 10 false 2 3.042,7.198 3.146,7.365 0.104,0.167 10 false 1 4.146,7.198 4.26,7.365 0.115,0.167 10 false 3 3.052,7.76 3.156,7.927 0.104,0.167 10 false 4 4.156,7.75 4.281,7.917 0.125,0.167 10 false 2 5.271,0.854 5.448,1.01 0.177,0.156 10 false 40 5.271,2.115 5.448,2.271 0.177,0.156 10 false 39 5.271,3.354 5.458,3.521 0.188,0.167 10 false 38 5.198,7.719 5.469,7.875 0.271,0.156 10 false 106 5.271,4.656 5.469,4.813 0.198,0.156 10 false 37 5.271,5.927 5.469,6.083 0.198,0.156 10 false 36 5.271,7.208 5.469,7.365 0.198,0.156 10 false 35 1.427,7.49 1.542,7.656 0.115,0.167 10 false 1 1.427,8.271 1.542,8.438 0.115,0.167 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)
a.
A115969C08
0.135,1.51 0.458,1.729 0.323,0.219 0.146,1.844 0.469,2.063 0.323,0.219 0.146,2.177 0.469,2.396 0.323,0.219 0.615,1.51 0.938,1.729 0.323,0.219 0.615,1.844 0.938,2.063 0.323,0.219 0.615,2.177 0.938,2.396 0.323,0.219 1.354,2.302 0.833,2.813 true 0.167,0.094 0.458,0.354 0.292,0.26 10 false *a 0.656,2.813 1.26,3.073 0.604,0.26 10 false +B (+) 0.208,2.208 0.604,2.49 0.396,0.281 10 false C7 0.677,1.875 1,2.094 0.323,0.219 10 false C13 0.688,2.219 1.042,2.427 0.354,0.208 10 false C14 0.677,1.542 1.01,1.729 0.333,0.188 10 false C12 0.208,1.542 0.604,1.823 0.396,0.281 10 false C5 0.208,1.875 0.542,2.063 0.333,0.188 10 false C6
*a Front view of wire harness connector
(to Ignition Coil Assembly)


Disconnect the ignition coil assembly connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C5-1 (+B) - Body ground Ignition switch ON 11 to 14 V
C14-1 (+B) - Body ground Ignition switch ON 11 to 14 V
C6-1 (+B) - Body ground Ignition switch ON 11 to 14 V
C13-1 (+B) - Body ground Ignition switch ON 11 to 14 V
C7-1 (+B) - Body ground Ignition switch ON 11 to 14 V
C12-1 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - IGNITION SWITCH)

2.CHECK HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
a.

Disconnect the ignition coil assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C5-4 (GND) - Body ground Always Below 1 Ω
C14-4 (GND) - Body ground Always Below 1 Ω
C6-4 (GND) - Body ground Always Below 1 Ω
C13-4 (GND) - Body ground Always Below 1 Ω
C7-4 (GND) - Body ground Always Below 1 Ω
C12-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the ignition coil assembly connectors.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C5-2 (IGF) - C39-106 (IGF) Always Below 1 Ω
C14-2 (IGF) - C39-106 (IGF) Always Below 1 Ω
C6-2 (IGF) - C39-106 (IGF) Always Below 1 Ω
C13-2 (IGF) - C39-106 (IGF) Always Below 1 Ω
C7-2 (IGF) - C39-106 (IGF) Always Below 1 Ω
C12-2 (IGF) - C39-106 (IGF) Always Below 1 Ω
C5-3 (IGT1) - C39-40 (IGT1) Always Below 1 Ω
C14-3 (IGT2) - C39-39 (IGT2) Always Below 1 Ω
C6-3 (IGT3) - C39-38 (IGT3) Always Below 1 Ω
C13-3 (IGT4) - C39-37 (IGT4) Always Below 1 Ω
C7-3 (IGT5) - C39-36 (IGT5) Always Below 1 Ω
C12-3 (IGT6) - C39-35 (IGT6) Always Below 1 Ω
C5-2 (IGF) or C39-106 (IGF) - Body ground Always 10 kΩ or higher
C14-2 (IGF) or C39-106 (IGF) - Body ground Always 10 kΩ or higher
C6-2 (IGF) or C39-106 (IGF) - Body ground Always 10 kΩ or higher
C13-2 (IGF) or C39-106 (IGF) - Body ground Always 10 kΩ or higher
C7-2 (IGF) or C39-106 (IGF) - Body ground Always 10 kΩ or higher
C12-2 (IGF) or C39-106 (IGF) - Body ground Always 10 kΩ or higher
C5-3 (IGT1) or C39-40 (IGT1) - Body ground Always 10 kΩ or higher
C14-3 (IGT2) or C39-39 (IGT2) - Body ground Always 10 kΩ or higher
C6-3 (IGT3) or C39-38 (IGT3) - Body ground Always 10 kΩ or higher
C13-3 (IGT4) or C39-37 (IGT4) - Body ground Always 10 kΩ or higher
C7-3 (IGT5) or C39-36 (IGT5) - Body ground Always 10 kΩ or higher
C12-3 (IGT6) or C39-35 (IGT6) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353, P0354, P0355 OR P0356)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353, P0354, P0355 OR P0356)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

d.

Shuffle the arrangement of the ignition coil assemblies (among No. 1 to No. 6 cylinders).

NOTICE:

Do not change the location of the connectors.



e.

Perform a simulation test.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

g.

Read the DTCs.

Result:
Result Engine Condition
Same DTC output A
Different ignition coil DTC output B




A

B