Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0500  Vehicle Speed Sensor "A"  


DESCRIPTION

Manual Transmission Models:
·

Vehicles which are equipped with a manual transmission detect the vehicle speed using the speed sensor. The speed sensor transmits a 4-pulse signal for every revolution of the rotor shaft, which is rotated by the transmission output shaft via the driven gear. The 4-pulse signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter. The signal is then transmitted to the ECM. The ECM determines the vehicle speed based on the frequency of the pulse signal.


A115900E01
3.722,1.871 5.142,2.034 1.420,0.163 10 Combination Meter 3.113,0.568 3.921,0.731 0.809,0.163 10 4-Pulse 5.039,0.568 5.848,0.731 0.809,0.163 10 4-Pulse 6.055,1.31 6.502,1.473 0.448,0.163 10 ECM 1.859,1.831 2.823,2.202 0.964,0.371 10 No. 1 Vehicle Speed Sensor

Automatic Transmission Models:
·

Vehicles, which are equipped with ABS (Anti-lock Brake System), detect the vehicle speed using the skidcontrol ECU and wheel speed sensor. The wheel speed sensor monitors the wheel rotation speed andsends a signal to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter. The ECM determines the vehiclespeed based on the frequency of the pulse signal.


A115899E20
0.43,1.047 1.579,1.425 1.149,0.378 10 from Wheel Speed Sensor 1.817,1.96 3.237,2.123 1.420,0.163 10 Skid Control ECU 3.722,1.96 5.142,2.123 1.420,0.163 10 Combination Meter 2.976,0.599 3.784,0.776 0.809,0.177 10 Pulse Signal 4.902,0.599 5.711,0.776 0.809,0.177 10 Pulse Signal 6.045,1.324 6.492,1.486 0.448,0.163 10 ECM

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0500 Vehicle Speed Sensor "A" Conditions (a), (b), (c) and (d) are met for 8 seconds or more (2 trip detection logic):

(a) Engine coolant temperature is 70°C (158°F) or higher.

(b) Engine speed is 1,500 to 4,000 rpm

(c) Engine load is 31.6% or more

(d) No speed signal is input to the ECM.


Conditions (a) and (b) are met for 5 seconds or more (2 trip detection logic):

(a) During the fuel-cut operation.

(b) No speed signal is input to the ECM.


·

Open or short in speed signal circuit

·

Combination meter assembly

·

Speedometer Sensor

·

Skid control ECU

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

Automatic Transmission Models:

The ECM assumes that the vehicle is being driven when the indicated vehicle speed is 9 km/h (5.59 mph) or more. If there is no speed signal from the combination meter despite these conditions being met, theECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL andstores the DTC.

Manual Transmission Models:

The ECM assumes that the vehicle is being driven when the indicated engine speed is 2000 to 5000 rpm and the engine load calculated by the ECM is more than a certain level or the idle fuel-cut operation* is being executed. If there is no signal from the vehicle speed sensor, despite these conditions being met,the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL andsets the DTC.

*: Idle fuel-cut is executed when the throttle valve is fully closed and engine speed is over 2800 rpm.

WIRING DIAGRAM

A288657E02
5.323,1.01 5.688,1.167 0.365,0.156 10 false SPD 1.219,1.198 1.448,1.354 0.229,0.156 10 false SE 1.177,0.646 1.5,0.802 0.323,0.156 10 false IG+ 1.51,0.563 1.635,0.719 0.125,0.156 10 false 1 1.51,0.844 1.635,1 0.125,0.156 10 false 3 2.542,0.844 2.667,1 0.125,0.156 10 false 9 4.208,0.76 4.333,0.917 0.125,0.156 10 false 8 5.146,0.76 5.271,0.917 0.125,0.156 10 false 8 2.469,0.552 2.656,0.708 0.188,0.156 10 false 13 2.542,1.646 2.823,1.802 0.281,0.156 10 false L25 1.51,1.115 1.635,1.271 0.125,0.156 10 false 2 1.135,2.719 1.448,2.875 0.313,0.156 10 false SP1 1.51,2.635 1.708,2.792 0.198,0.156 10 false 22 1.25,0.917 1.479,1.073 0.229,0.156 10 false SI 2.542,1.781 4.406,1.948 1.865,0.167 10 false Combination Meter Assembly 5.635,1.656 6.875,1.917 1.24,0.26 10 false I84*3, A29*4 5.844,1.813 6.188,1.99 0.344,0.177 10 false ECM 0.188,1.604 0.479,1.771 0.292,0.167 10 false C96 0.188,1.781 1.667,1.948 1.479,0.167 10 false Speedometer Sensor*1 1.594,3.146 1.885,3.313 0.292,0.167 10 false A20 1.594,3.323 2.938,3.49 1.344,0.167 10 false Skid Control ECU*2 4.354,2.323 5.146,2.49 0.792,0.167 10 false *1: w/o ABS 4.354,2.698 5.146,2.865 0.792,0.167 10 false *2: w/ ABS 4.354,3.021 5.427,3.219 1.073,0.198 10 false *3: for LHD 4.354,3.365 5.427,3.563 1.073,0.198 10 false *4:for RHD 3.896,0.865 4.208,1.063 0.313,0.198 10 false +S 2.729,0.677 3.188,0.875 0.458,0.198 10 false IG+ 2.729,0.979 3.042,1.177 0.313,0.198 10 false SI

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OPERATION OF SPEEDOMETER
a.

Drive the vehicle and check whether the operation of the speedometer in the combination meter assembly is normal.

HINT:
·

The vehicle speed sensor is operating normally if the speedometer reading is normal.


·

If the speedometer does not operate, check it by following the procedure described in Speedometer Malfunction.




Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (VEHICLE SPEED)

NG

2.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Vehicle Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Vehicle Speed
50003 234 10

e.

Drive the vehicle.


f.

Read the value displayed on the GTS.

OK:

Vehicle speeds displayed on GTS and speedometer display are equal.


Result:
Proceed to
OK
NG




OK

NG

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
L25-8 - I84-8 (SPD) Always Below 1 Ω
L25-8 or I84-8 (SPD) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
L25-8 - A29-8 (SPD) Always Below 1 Ω
L25-8 or A29-8 (SPD) - Body ground Always 10 kΩ or higher


HINT:

If the wire has a short, check the speed signal circuit in other systems related to the vehicle speed signal (e.g. tire pressure warning system, audio system, etc.).



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (OTHER SYSTEM RELATED TO SPEEDOMETER)