Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, the positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High When conditions (a), (b) and (c) met, positive (+B) battery voltage 10.5 V or more applied to ECM for 20 seconds (1 trip detection logic)

(a) Vehicle speed 20 km/h (12.4 mph) or more

(b) Engine speed 1000 rpm or more

(c) STA signal ON


·

Starter relay (ST) circuit

·

Ignition switch

·

ECM


Comes on DTC stored

WIRING DIAGRAM

A331587E02
6.156,1.906 6.615,2.104 0.458,0.198 10 false STA 5.521,1.917 5.979,2.115 0.458,0.198 10 false I84 5.865,1.917 6.323,2.115 0.458,0.198 10 false A29 5.448,1.74 6.219,1.938 0.771,0.198 10 false 48*1 5.802,1.75 6.573,1.948 0.771,0.198 10 false 48*2 4.719,1.125 5.031,1.323 0.313,0.198 10 false ST 4.135,0.302 4.292,0.5 0.156,0.198 10 false 3 3.823,0.521 4.281,0.719 0.458,0.198 10 false ST1 3.281,0.531 3.74,0.729 0.458,0.198 10 false AM1 1.521,0.594 1.979,0.792 0.458,0.198 10 false AM1 0.615,1.115 1.073,1.313 0.458,0.198 10 false ALT 1.531,2.094 1.99,2.292 0.458,0.198 10 false AM2 3.229,2.24 3.385,2.438 0.156,0.198 10 false 1 3.24,3.094 3.396,3.292 0.156,0.198 10 false 2 2.573,2.26 2.729,2.458 0.156,0.198 10 false 5 2.552,3.083 2.708,3.281 0.156,0.198 10 false 3 3.438,2.667 3.75,2.865 0.313,0.198 10 false ST 2.656,3.729 2.969,3.927 0.313,0.198 10 false D2 1.625,4.365 1.938,4.563 0.313,0.198 10 false D3 2.771,3.521 2.927,3.719 0.156,0.198 10 false 1 1.667,4.135 1.823,4.333 0.156,0.198 10 false 1 2.323,4.833 3.396,5.031 1.073,0.198 10 false Starter 0.615,2.583 1.688,2.781 1.073,0.198 10 false FL MAIN 0.771,4.948 1.844,5.146 1.073,0.198 10 false Battery 3.083,0.271 3.24,0.469 0.156,0.198 10 false 4 5.073,4.417 6.146,4.615 1.073,0.198 10 false *1: for LHD 5.083,4.677 6.156,4.875 1.073,0.198 10 false *2: for RHD 3.208,0.906 3.667,1.104 0.458,0.198 10 false L21 3.229,1.073 4.135,1.406 0.906,0.333 10 false Ignition Switch Assembly 6.333,2.844 6.792,3.042 0.458,0.198 10 false ECM

CAUTION / NOTICE / HINT

HINT:
·

The following troubleshooting flowchart is based on the premise that the engine is cranked normally.

If the engine will not crank, proceed to the Problem Symptoms Table.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>PROBLEM SYMPTOMS TABLE

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

OK:
Condition GTS Display
Driving at 20 km/h (12.4 mph) or more OFF (Starter signal off)



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT IGNITION SWITCH ASSEMBLY
2.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>1GR-FE (STARTING)>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT ECM (STA TERMINAL VOLTAGE)

NG

REPLACE IGNITION SWITCH ASSEMBLY

3.INSPECT ECM (STA TERMINAL VOLTAGE)
a.
A182543C03
1.094,0.844 1.469,1.073 0.375,0.229 1.906,0.854 2.292,1.094 0.385,0.24 2.208,2.073 2.604,2.885 false 0.156,0.177 0.479,0.365 0.323,0.188 10 false *a 1.146,0.875 1.448,1.042 0.302,0.167 10 false I84 2.646,2.896 3.24,3.083 0.594,0.188 10 false 48 (STA) 2,0.896 2.458,1.094 0.458,0.198 10 false A29 1.156,0.667 1.469,0.865 0.313,0.198 10 false *A 2.01,0.667 2.323,0.865 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in thetable below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
I84-48 (STA) - Body ground Ignition switch ON 11 to 14 V

for RHD
Tester Connection Condition Specified Condition
A29-48 (STA) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - IGNITION SWITCH, ST RELAY)