Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0657  Actuator Supply Voltage Circuit / Open  


DESCRIPTION

The ECM monitors the output voltage to the throttle actuator. This self-check ensures that the ECM is functioning properly. The output voltage is usually 0 V when the ignition switch is turned off. If the output voltage is higher than 7 volts when the ignition switch is turned off, the ECM will illuminate the MIL and store a DTC when the ignition switch is turned ON.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0657 Actuator Supply Voltage Circuit / Open A throttle actuator power supply error (1 trip detectionlogic). ECM Comes on DTC stored

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the GTS off.

5.

Turn the ignition switch off.

6.

Disconnect the GTS.

7.

Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

8.

Connect the cable to the negative (-) battery terminal.

9.

Turn the ignition switch on (IG).

10.

Wait 10 seconds or more.

11.

Turn the ignition switch off.

12.

Wait 15 seconds or more.

13.

Connect the GTS to the DLC3.

14.

Turn the ignition switch on (IG) and turn the GTS on.

15.

Wait 5 seconds or more.

16.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

17.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



18.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

19.

Input the DTC: P0657.

20.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ OUTPUT DTC (DTC P0657)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.


g.

Connect the cable to the negative (-) battery terminal.


h.

Turn the ignition switch ON for 10 seconds.


i.

Turn the ignition switch off.


j.

Wait 15 seconds or more.


k.

Turn the ignition switch to ON.


l.

Turn the GTS on.


m.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

n.

Read the DTCs.

Result:
Result Proceed to
DTC is not output A
DTC P0657 is output B




A

B