Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P2118  Throttle Actuator Control Motor Current Range / Performance  


DESCRIPTION

The ETCS (Electronic Throttle Control System) has a dedicated power supply circuit. The voltage (+BM) is monitored and when it is low (below 4 V), the ECM determines that there is a malfunction in the ETCS and cuts off the current to the throttle actuator.

When the voltage becomes unstable, the ETCS itself becomes unstable. For this reason, when the voltage is low, the current to the throttle actuator is cut. If repairs are made and the system returns to normal, turn the ignition switch off. The ECM then allows the current to flow to the throttle actuator so that it can be restarted.

HINT:

The ETCS does not use a throttle cable.


A112629E98
0.24,1.76 0.844,2.135 0.604,0.375 10 false from Battery 0.792,3.5 2.01,3.698 1.219,0.198 10 false Throttle Actuator 1.229,2.01 2.167,2.208 0.938,0.198 10 false ETCS 5.604,4.219 6.052,4.417 0.448,0.198 10 false ECM 4.76,1.698 5.208,1.896 0.448,0.198 10 false +BM 4.76,3.75 5.281,3.948 0.521,0.198 10 false ME01 4.76,2.427 5.073,2.625 0.313,0.198 10 false M+ 4.76,3.063 5.073,3.26 0.313,0.198 10 false M- 5.938,2.438 6.552,3.156 0.615,0.719 10 false Throttle Actuator Control Circuit 4.76,0.917 5.208,1.115 0.448,0.198 10 false +B 0.229,0.802 0.781,1.344 0.552,0.542 10 false from EFI MAIN Relay 5.938,0.75 6.479,1.469 0.542,0.719 10 false Power Source Circuit for CPU

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2118 Throttle Actuator Control Motor Current Range / Performance An open in the ETCS power source (+BM) circuit (1 trip detection logic).
·

Open in ETCS power source circuit

·

Battery

·

Battery terminals

·

ETCS fuse

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM monitors the battery supply voltage applied to the throttle actuator.

When the power supply voltage (+BM) drops below 4 V for 0.8 seconds or more, the ECM interprets this as an open in the power supply circuit (+BM). The ECM illuminates the MIL and stores the DTC.

CONFIRMATION DRIVING PATTERN

A199315E63
0.983,0.548 1.63,0.76 0.647,0.212 10 3000 rpm 1.24,1.924 1.621,2.142 0.381,0.219 10 Idling 0.451,2.211 1.64,2.381 1.189,0.17 10 Ignition Switch ON 3.146,2.21 4.716,2.347 1.571,0.138 10 Approximately 5 seconds 3.468,2.799 4.791,2.983 1.323,0.184 10 16 seconds or more 2.015,2.309 2.218,2.539 0.203,0.23 10 [A] 6.014,3.229 6.242,3.415 0.228,0.186 10 [C] 4.603,0.413 4.831,0.599 0.228,0.186 10 [B]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch ON and turn the GTS on [A].

6.

Start the engine.

7.

Slowly depress the accelerator pedal, raise the engine speed to approximately 3000 rpm over approximately 5 seconds, and then idle the engine [B].

8.

Check that 16 seconds or more have elapsed since the engine was started.

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P2118.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.




FAIL-SAFE

When this DTC, or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

A333588E01
4.271,1.271 4.729,1.469 0.458,0.198 10 false I84 4.573,1.271 5.031,1.469 0.458,0.198 10 false A29 4.573,1.938 5.031,2.135 0.458,0.198 10 false C39 4.573,2.771 5.031,2.969 0.458,0.198 10 false C39 4.563,3.406 5.021,3.604 0.458,0.198 10 false C39 4.573,3.958 5.031,4.156 0.458,0.198 10 false C39 4.552,4.448 5.01,4.646 0.458,0.198 10 false C39 4.229,1.052 4.844,1.25 0.615,0.198 10 false 3*1 4.573,1.063 5.188,1.26 0.615,0.198 10 false 3*2 4.594,1.74 4.906,1.938 0.313,0.198 10 false 19 4.615,2.583 4.927,2.781 0.313,0.198 10 false 18 4.615,3.219 4.927,3.417 0.313,0.198 10 false 41 4.615,3.781 4.927,3.979 0.313,0.198 10 false 20 4.604,4.281 4.917,4.479 0.313,0.198 10 false 81 4.885,1.156 5.344,1.354 0.458,0.198 10 false +BM 4.896,1.823 5.208,2.021 0.313,0.198 10 false M+ 4.885,2.656 5.198,2.854 0.313,0.198 10 false M- 4.885,3.375 5.5,3.573 0.615,0.198 10 false GE01 4.896,3.844 5.51,4.042 0.615,0.198 10 false ME01 4.906,4.438 5.219,4.635 0.313,0.198 10 false E1 3.365,3.156 4.896,3.354 1.531,0.198 10 false (Shielded) 1.75,3.135 2.063,3.333 0.313,0.198 10 false C4 1.771,3.302 3.229,3.927 1.458,0.625 10 false Throttle Actuator (Built into Throttle with motor body assembly) 3.063,1.813 3.219,2.01 0.156,0.198 10 false 2 3.052,2.615 3.208,2.813 0.156,0.198 10 false 1 2.656,2.052 2.969,2.25 0.313,0.198 10 false M+ 2.688,2.844 3,3.042 0.313,0.198 10 false M- 1.677,1.448 2.292,1.646 0.615,0.198 10 false ETCS 1,2.844 2.073,3.042 1.073,0.198 10 false FL MAIN 1.125,4.49 2.198,4.688 1.073,0.198 10 false Battery 5.427,1.854 6.479,2.375 1.052,0.521 10 false Throttle Actuator Control Circuit 5.563,5.156 6.021,5.354 0.458,0.198 10 false ECM 3.76,4.927 4.833,5.125 1.073,0.198 10 false *1: RHD 3.771,5.135 4.844,5.333 1.073,0.198 10 false *2: LHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (+BM VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Ptrl Throttle / +BM Voltage.

Powertrain > Engine and ECT > Data List
Tester Display
+BM Voltage
50003 234 279

e.

Read the value displayed on the GTS.

Result:
Result Proceed to
Less than 4 V A
11 to 14 V B




A

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY, BODY GROUND)

B

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY, BODY GROUND)
a.

Disconnect the ECM connector.


A333590C01
0.958,0.292 1.427,0.521 0.469,0.229 1,2.354 1.458,2.583 0.458,0.229 1.99,2.354 2.469,2.583 0.479,0.229 2.188,0.927 2.417,0.396 2.417,0.396 2.604,0.396 true 2,1.302 2.219,1.885 2.219,1.885 2.49,1.885 true 1.688,2.99 2.438,4.042 2.438,4.042 2.677,4.042 true 1.052,0.302 1.51,0.5 0.458,0.198 10 false C39 1.115,2.385 1.573,2.583 0.458,0.198 10 false I84 2.156,2.375 2.615,2.573 0.458,0.198 10 false A29 1.104,2.146 1.417,2.344 0.313,0.198 10 false *A 2.146,2.167 2.458,2.365 0.313,0.198 10 false *B 2.677,0.323 3.406,0.521 0.729,0.198 10 false 20 (ME01) 2.531,1.802 3,2.021 0.469,0.219 10 false 81 (E1) 2.719,3.958 3.281,4.188 0.563,0.229 10 false 3 (+BM) 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to ECM)


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
I84-3 (+BM) - Body ground Always 11 to 14 V

for RHD
Tester Connection Condition Specified Condition
A29-3 (+BM) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C39-20 (ME01) - Body ground Always Below 1 Ω
C39-81 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR