Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P2120  Throttle / Pedal Position Sensor / Switch "D" Circuit  P2122  Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input  P2123  Throttle / Pedal Position Sensor / Switch "D" Circuit High Input  P2125  Throttle / Pedal Position Sensor / Switch "E" Circuit  P2127  Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input  P2128  Throttle / Pedal Position Sensor / Switch "E" Circuit High Input  P2138  Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation  


DESCRIPTION

HINT:

This ETCS (Electronic Throttle Control System) does not use a throttle cable.


The accelerator pedal position sensor is built into the accelerator pedal sensor assembly and has 2 sensor circuits: VPA (main) and VPA2 (sub). This sensor is a non-contact type sensor and uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds. The voltage, which is applied to terminals VPA and VPA2 of the ECM, varies between 0.5 V and 4.75 V in proportion to the operating angle of the accelerator pedal (throttle valve). A signal from VPA indicates the actual accelerator pedal opening angle (throttle valve opening angle) and is used for engine control. A signal from VPA2 conveys the status of the VPA circuit and is used to check the accelerator pedal position sensor itself.

The ECM monitors the actual accelerator pedal opening angle (throttle valve opening angle) through the signals from VPA and VPA2, and controls the throttle actuator according to these signals.

A112620E23
0.173,3.81 2.341,3.954 2.168,0.144 10 Accelerator Pedal Position Sensor 0.759,0.75 1.239,0.932 0.480,0.181 10 Magnet 1.214,1.297 1.741,1.478 0.526,0.181 10 No. 1 IC 1.081,1.02 1.608,1.201 0.526,0.181 10 No. 2 IC 2.067,1.739 2.362,1.921 0.295,0.181 10 VPA 2.067,2.071 2.362,2.252 0.295,0.181 10 EPA 2.067,2.393 2.462,2.574 0.395,0.181 10 VCPA 2.067,2.687 2.439,2.869 0.372,0.181 10 VPA2 2.067,3.005 2.439,3.186 0.372,0.181 10 EPA2 2.067,3.327 2.447,3.508 0.380,0.181 10 VCP2 2.693,1.392 3.018,1.574 0.326,0.181 10 ECM 4.267,1.548 4.423,1.729 0.156,0.181 10 *1 5.864,1.548 6.020,1.729 0.156,0.181 10 *2 3.938,1.842 4.225,2.023 0.287,0.181 10 4.55 3.86,2.047 4.225,2.229 0.365,0.181 10 3.988 3.938,2.253 4.225,2.434 0.287,0.181 10 3.75 3.86,2.458 4.225,2.640 0.365,0.181 10 3.188 3.991,2.823 4.201,3.004 0.210,0.181 10 1.6 3.991,3.042 4.201,3.223 0.210,0.181 10 0.8 4.411,3.346 4.698,3.527 0.287,0.181 10 0.29 4.259,3.596 4.414,3.777 0.156,0.181 10 0 5.784,3.596 6.071,3.777 0.287,0.181 10 15.9 6.443,1.835 6.821,1.983 0.378,0.148 10 VPA2 6.482,2.255 6.782,2.398 0.299,0.143 10 VPA 4.682,3.587 5.606,3.748 0.924,0.160 10 Usable Range 4.299,3.896 6.889,4.098 2.590,0.202 10 Accelerator Pedal Operating Angle (°) 4.089,4.979 6.368,5.160 2.279,0.181 10 *1: Accelerator Pedal Fully Released 4.089,5.287 6.476,5.452 2.387,0.165 10 *2: Accelerator Pedal Fully Depressed 4.355,2.014 4.234,1.93 false 4.346,2.182 4.234,2.126 false 4.346,2.228 4.234,2.322 false 4.346,2.397 4.234,2.518 false 4.346,2.901 4.215,2.901 false 4.355,3.116 4.206,3.116 false 0.686,3.387 1.166,3.568 0.480,0.181 10 Magnet 0.843,2.878 0.975,1.099 0.975,1.099 1.062,1.099 false 1.74,0.629 3.979,0.954 2.239,0.325 10 Accelerator Pedal Position Sensor Output Voltage (V) 4.355,1.965 3.925,0.728 false 0.847,2.267 0.649,0.827 0.649,0.827 0.752,0.827 false 1.068,2.561 1.068,1.37 1.068,1.37 1.179,1.37 false 0.843,3.103 0.605,3.461 0.605,3.461 0.679,3.461 false

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit VPA fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic).
·

Accelerator Pedal sensor assembly

·

ECM


Comes on DTC stored
P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input VPA is 0.4 V or less for 0.5 seconds or more when the accelerator pedal is fully released (1 trip detection logic).
·

Accelerator Pedal sensor assembly

·

Open in VCPA circuit

·

Open or ground short in VPA circuit

·

ECM


Comes on DTC stored
P2123 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input VPA is 4.8 V or higher for 2.0 seconds or more (1 trip detection logic).
·

Accelerator Pedal sensor assembly

·

Open in EPA circuit

·

ECM


Comes on DTC stored
P2125 Throttle / Pedal Position Sensor / Switch "E" Circuit VPA2 fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic).
·

Accelerator Pedal sensor assembly

·

ECM


Comes on DTC stored
P2127 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input VPA2 is 1.2 V or less for 0.5 seconds or more when the accelerator pedal is fully released (1 trip detection logic).
·

Accelerator Pedal sensor assembly

·

Open in VCP2 circuit

·

Open or ground short in VPA2 circuit

·

ECM


Comes on DTC stored
P2128 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic):
(a) VPA2 is 4.8 V or higher.
(b) VPA is between 0.4 V and 3.45 V.
·

Accelerator Pedal sensor assembly

·

Open in EPA2 circuit

·

ECM


Comes on DTC stored
P2138 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic):
(a) The difference between VPA and VPA2 is 0.02 V or less.
(b) VPA is 0.4 V or less and VPA2 is 1.2 V or less.
·

Short between VPA and VPA2 circuits

·

Accelerator Pedal sensor assembly

·

ECM


Comes on DTC stored

HINT:

When any of these DTCs are output, check the Accelerator Pedal sensor assembly voltage by entering the following menus: Powertrain / Engine and ECT / Data List / ETCS / Accel Sensor Out No.1 and Accel Sensor Out No.2.

Trouble Area Accel Sensor Out No. 1
When Accelerator Pedal Released
Accel Sensor Out No. 2
When Accelerator Pedal Released
Accel Sensor Out No. 1
When Accelerator Pedal Depressed
Accel Sensor Out No. 2
When Accelerator Pedal Depressed
VCP circuit open 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V
Open or ground short in VPA circuit 0 to 0.2 V 1.2 to 2.0 V 0 to 0.2 V 3.4 to 5.0 V
Open or ground short in VPA2 circuit 0.5 to 1.1 V 0 to 0.2 V 2.6 to 4.5 V 0 to 0.2 V
EPA circuit open 4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V
Normal condition 0.5 to 1.1 V 1.2 to 2.0 V 2.6 to 4.5 V 3.4 to 4.75 V


HINT:

Accelerator pedal positions are expressed as voltages.


MONITOR DESCRIPTION

When either output voltage of VPA or VPA2 deviates from the standard range, or the difference between the output voltages of the 2 sensor circuits is below the threshold, the ECM determines that there is a malfunction in the APP sensor. The ECM then illuminates the MIL and stores a DTC.

Example:

When the output voltage of VPA drops below 0.4 V for more than 0.5 seconds when the accelerator pedal is fully depressed, DTC P2122 is stored.

CONFIRMATION DRIVING PATTERN

A199317E77
3.635,2.01 2.771,1.302 2.771,1.302 2.927,1.302 false 4.729,2.438 5.115,1.792 5.115,1.792 5.26,1.792 false 2.208,2.448 2.438,2.104 2.438,2.104 2.542,2.104 false 0.125,0.094 1.74,0.271 1.615,0.177 10 false Accelerator Pedal State 0.865,0.417 1.583,0.563 0.719,0.146 10 false Depressed 0.948,0.875 1.594,1.031 0.646,0.156 10 false Released 0.667,2.406 1.604,2.76 0.938,0.354 10 false Ignition Switch on (IG) 2.094,2.49 2.292,2.677 0.198,0.188 10 false [A] 4.417,3.438 4.635,3.615 0.219,0.177 10 false [C] 5.365,1.688 6.125,1.844 0.76,0.156 10 false Released 2.875,3.052 3.552,3.229 0.677,0.177 10 false 5 seconds 3.01,1.229 3.823,1.406 0.813,0.177 10 false Depressed 3.865,1.125 4.271,1.323 0.406,0.198 10 false [B] 2.594,2.01 3.24,2.167 0.646,0.156 10 false Released

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Fully depress and release the accelerator pedal [B].

7.

Check that 5 seconds or more have elapsed since the ignition switch ON.

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P2120, P2122, P2123, P2125, P2127, P2128 or P2138.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.




FAIL-SAFE

When DTC P2120, P2121, P2122, P2123, P2125, P2127, P2128 or P2138 is stored, the ECM enters failsafe mode. If either of the 2 sensor circuits malfunctions, the ECM limits the engine output. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles.

Fail-safe mode continues until a pass condition is detected, and the ignition switch is turned off.

WIRING DIAGRAM

A149601E38
0.448,3.188 2.083,3.615 1.635,0.427 10 false Accelerator Pedal Sensor Assembly 1.594,0.479 2.063,0.688 0.469,0.208 10 false VPA 1.594,0.896 2.063,1.104 0.469,0.208 10 false EPA 1.49,1.302 2.083,1.51 0.594,0.208 10 false VCPA 1.49,1.729 2.083,1.938 0.594,0.208 10 false VPA2 1.49,2.135 2.083,2.344 0.594,0.208 10 false EPA2 1.49,2.563 2.083,2.771 0.594,0.208 10 false VCP2 5.604,0.396 6,0.604 0.396,0.208 10 false VPA 5.333,0.375 5.51,0.583 0.177,0.208 10 false 55 5.333,0.792 5.51,1 0.177,0.208 10 false 59 5.333,1.208 5.51,1.417 0.177,0.208 10 false 57 5.333,1.635 5.51,1.844 0.177,0.208 10 false 56 5.333,2.052 5.51,2.26 0.177,0.208 10 false 60 5.333,2.479 5.51,2.688 0.177,0.208 10 false 58 5.604,0.802 6,1.01 0.396,0.208 10 false EPA 5.604,1.25 6.052,1.458 0.448,0.208 10 false VCPA 5.604,1.667 6.052,1.875 0.448,0.208 10 false VPA2 5.604,2.083 6.042,2.292 0.438,0.208 10 false EPA2 5.604,2.5 6.198,2.708 0.594,0.208 10 false VCP2 1.99,0.354 2.198,0.563 0.208,0.208 10 false 6 1.99,0.781 2.198,0.99 0.208,0.208 10 false 5 1.99,1.198 2.198,1.406 0.208,0.208 10 false 4 1.99,1.625 2.198,1.833 0.208,0.208 10 false 3 1.99,2.042 2.198,2.25 0.208,0.208 10 false 2 1.99,2.469 2.198,2.677 0.208,0.208 10 false 1 6,3.167 6.396,3.365 0.396,0.198 10 false ECM 5.76,3.021 6.771,3.208 1.01,0.188 10 false I84*1, A29*2 0.323,3.052 0.604,3.24 0.281,0.188 10 false I43 3.271,3.042 4.344,3.24 1.073,0.198 10 false *1: for LHD 3.281,3.25 4.354,3.448 1.073,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

HINT:
·

These DTCs relate to the Accelerator Pedal Position (APP) sensor.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (Accel Sensor Out)
A208621C04
0.67,1.751 0.875,1.926 0.205,0.175 10 *a 2.612,1.751 2.803,1.926 0.191,0.175 10 *b
*a Fully Depressed
*b Fully Released


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Accel Sensor Out No.1 and Accel Sensor Out No.2.

Powertrain > Engine and ECT > Data List
Tester Display
Accel Sensor Out No.1
Accel Sensor Out No.2
50003 234 280,281

e.

Read the value displayed on the GTS.

Standard Voltage:
Accelerator Pedal Operation Accel Sensor Out No.1 Accel Sensor Out No.2
Fully Released 0.5 to 1.1 V 1.2 to 2.0 V
Fully Depressed 2.6 to 4.5 V 3.4 to 4.75 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM)
2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM)
a.

Disconnect the Accelerator Pedal sensor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
I43-6 (VPA) - I84-55 (VPA) Always Below 1 Ω
I43-5 (EPA) - I84-59 (EPA) Always Below 1 Ω
I43-4 (VCPA) - I84-57 (VCPA) Always Below 1 Ω
I43-3 (VPA2) - I84-56 (VPA2) Always Below 1 Ω
I43-2 (EPA2) - I84-60 (EPA2) Always Below 1 Ω
I43-1 (VCP2) - I84-58 (VCP2) Always Below 1 Ω
I43-6 (VPA) or I84-55 (VPA) - Body ground Always 10 kΩ or higher
I43-5 (EPA) or I84-59 (EPA) - Body ground Always 10 kΩ or higher
I43-4 (VCPA) or I84-57 (VCPA) - Body ground Always 10 kΩ or higher
I43-3 (VPA2) or I84-56 (VPA2) - Body ground Always 10 kΩ or higher
I43-2 (EPA2) or I84-60 (EPA2) - Body ground Always 10 kΩ or higher
I43-1 (VCP2) or I84-58 (VCP2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
I43-6 (VPA) - A29-55 (VPA) Always Below 1 Ω
I43-5 (EPA) - A29-59 (EPA) Always Below 1 Ω
I43-4 (VCPA) - A29-57 (VCPA) Always Below 1 Ω
I43-3 (VPA2) - A29-56 (VPA2) Always Below 1 Ω
I43-2 (EPA2) - A29-60 (EPA2) Always Below 1 Ω
I43-1 (VCP2) - A29-58 (VCP2) Always Below 1 Ω
I43-6 (VPA) or A29-55 (VPA) - Body ground Always 10 kΩ or higher
I43-5 (EPA) or A29-59 (EPA) - Body ground Always 10 kΩ or higher
I43-4 (VCPA) or A29-57 (VCPA) - Body ground Always 10 kΩ or higher
I43-3 (VPA2) or A29-56 (VPA2) - Body ground Always 10 kΩ or higher
I43-2 (EPA2) or A29-60 (EPA2) - Body ground Always 10 kΩ or higher
I43-1 (VCP2) or A29-58 (VCP2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK Terminal Voltage (Power Source of Accelerator Pedal Sensor Assembly)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK Terminal Voltage (Power Source of Accelerator Pedal Sensor Assembly)
a.
A115666C06
0.344,1.625 0.729,1.875 0.385,0.25 0.708,2.5 1.302,1.854 false 1.354,2.5 1.469,1.875 false 1.99,2.5 1.74,1.875 false 2.5,2.479 1.885,1.865 false 0.208,0.167 0.594,0.396 0.385,0.229 10 false *a 1.781,2.563 2.177,2.729 0.396,0.167 10 false VCPA 0.479,2.542 0.938,2.771 0.458,0.229 10 false VCP2 2.427,2.552 2.75,2.719 0.323,0.167 10 false EPA 1.135,2.552 1.583,2.75 0.448,0.198 10 false EPA2 0.417,1.677 0.792,1.885 0.375,0.208 10 false I43
*a Front view of wire harness connector
(to Accelerator Pedal Position Sensor)


Disconnect the Accelerator Pedal sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I43-4 (VCPA) - I43-5 (EPA) Ignition switch ON 4.5 to 5.5 V
I43-1 (VCP2) - I43-2 (EPA2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.REPLACE ACCELERATOR PEDAL(W/SENSOR) ROD ASSEMBLY

NG

4.REPLACE ACCELERATOR PEDAL(W/SENSOR) ROD ASSEMBLY
a.

Replace the accelerator pedal sensor assembly.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL SENSOR ASSEMBLY DTCS)
5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL SENSOR ASSEMBLY DTCS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Turn the ignition switch ON and turn the GTS on.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

h.

Read the DTCs.

Result:
Result Proceed to
DTC P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138 are output A
DTC is not output B




A

B

END