Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P2237  Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)  P2238  Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)  P2239  Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)  P2240  Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 2 Sensor 1)  P2241  Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 2 Sensor 1)  P2242  Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 2 Sensor 1)  P2252  Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)  P2253  Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)  P2255  Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 2 Sensor 1)  P2256  Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 2 Sensor 1)  


DESCRIPTION

Refer to DTC P0031.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0031

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1) An open in the circuit between terminals A1A+ and A1A- of the A/F sensor while the engine is running (2 trip detection logic).
·

Open in air fuel ratio sensor (bank 1 sensor 1) circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

ECM


Comes on DTC stored
P2238 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1) Any of the following conditions are met (2 trip detection logic):
·

The A/F sensor output drops while the engine is running.

·

The voltage at terminal A1A+ is 0.5 V or less.

·

The voltage difference between terminals A1A+ and A1A- is 0.1 V or less.


·

Open or short in air fuel ratio sensor (bank 1 sensor 1) circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

ECM


Comes on DTC stored
P2239 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1) The A1A+ voltage is higher than 4.5 V (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1 sensor 1) circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

ECM


Comes on DTC stored
P2240 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 2 Sensor 1) An open in the circuit between terminals A2A+ and A2A- of the A/F sensor while the engine is running (2 trip detection logic).
·

Open in air fuel ratio sensor (bank 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

ECM


Comes on DTC stored
P2241 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 2 Sensor 1) Any of the following conditions are met (2 trip detection logic):
·

The A/F sensor output drops while the engine is running.

·

The voltage at terminal A2A+ is 0.5 V or less.

·

The voltage difference between terminals A2A+ and A2A- is 0.1 V or less.


·

Open or short in air fuel ratio sensor (bank 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

ECM


Comes on DTC stored
P2242 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 2 Sensor 1) The A2A+ voltage is higher than 4.5 V (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

ECM


Comes on DTC stored
P2252 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1) The A1A- voltage is 0.5 V or less (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1 sensor 1) circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

ECM


Comes on DTC stored
P2253 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1) The A1A- voltage is higher than 4.5 V (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1 sensor 1) circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

ECM


Comes on DTC stored
P2255 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 2 Sensor 1) The A2A- voltage is 0.5 V or less (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

ECM


Comes on DTC stored
P2256 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 2 Sensor 1) The A2A- voltage is higher than 4.5 V (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

These DTCs are stored when there is an open or short in the air fuel ratio sensor circuit, or if air fuel ratio sensor output drops. To detect these problems, the voltage of the air fuel ratio sensor is monitored when turning the ignition switch to ON, and the admittance (admittance is an electrical term that indicates the ease of flow of current) is checked while driving. If the voltage of the air fuel ratio sensor is between 0.5 V and 4.5 V, it is considered normal. If the voltage is out of the specified range, or the admittance is less than the standard value, the ECM will determine that there is a malfunction in the air fuel ratio sensor. If the same malfunction is detected in next driving cycle, the MIL will be illuminated and a DTC will be stored.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine and wait 5 minutes.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, idle the engine for 5 minutes and check the DTC judgment result again.




WIRING DIAGRAM

A333591E01
6.031,0.563 6.344,0.76 0.313,0.198 10 false 86 6.021,0.729 6.479,0.927 0.458,0.198 10 false C39 6.021,1.198 6.479,1.396 0.458,0.198 10 false C39 6.031,2.271 6.49,2.469 0.458,0.198 10 false C39 6.021,2.896 6.479,3.094 0.458,0.198 10 false C39 6.021,3.385 6.479,3.583 0.458,0.198 10 false C39 6.031,4.427 6.49,4.625 0.458,0.198 10 false C39 5.698,5.229 6.156,5.427 0.458,0.198 10 false I84 6.052,5.219 6.51,5.417 0.458,0.198 10 false A29 6.052,1.031 6.365,1.229 0.313,0.198 10 false 93 6.01,2.083 6.469,2.281 0.458,0.198 10 false 116 6.021,2.729 6.479,2.927 0.458,0.198 10 false 109 6.031,3.198 6.49,3.396 0.458,0.198 10 false 120 6,4.24 6.458,4.438 0.458,0.198 10 false 119 5.615,5.052 6.385,5.25 0.771,0.198 10 false 44*1 5.969,5.052 6.74,5.25 0.771,0.198 10 false 44*2 4.938,1.042 5.25,1.24 0.313,0.198 10 false *3 4.948,3.208 5.26,3.406 0.313,0.198 10 false *3 6.333,0.594 6.948,0.792 0.615,0.198 10 false HA1A 4.229,0.594 4.844,0.792 0.615,0.198 10 false HA1A 6.354,1.198 6.969,1.396 0.615,0.198 10 false A1A+ 6.354,2.25 6.969,2.448 0.615,0.198 10 false A1A- 6.344,2.771 6.958,2.969 0.615,0.198 10 false HA2A 4.229,2.792 4.844,2.99 0.615,0.198 10 false HA2A 6.354,3.375 6.969,3.573 0.615,0.198 10 false A2A+ 6.354,4.417 6.969,4.615 0.615,0.198 10 false A2A- 6.354,5.448 6.969,5.646 0.615,0.198 10 false MREL 6.469,6.073 6.927,6.271 0.458,0.198 10 false ECM 4.656,3.281 4.813,3.479 0.156,0.198 10 false 3 4.646,2.771 4.802,2.969 0.156,0.198 10 false 1 3.375,2.76 3.531,2.958 0.156,0.198 10 false 2 3.375,3.229 3.531,3.427 0.156,0.198 10 false 4 4.24,3.292 4.854,3.49 0.615,0.198 10 false A2A+ 3.604,2.781 3.917,2.979 0.313,0.198 10 false +B 3.583,3.271 4.198,3.469 0.615,0.198 10 false A2A- 4.25,1.115 4.865,1.313 0.615,0.198 10 false A1A+ 4.656,0.615 4.813,0.813 0.156,0.198 10 false 1 4.646,1.073 4.802,1.271 0.156,0.198 10 false 3 3.594,0.594 3.906,0.792 0.313,0.198 10 false +B 3.583,1.104 4.198,1.302 0.615,0.198 10 false A1A- 3.365,0.615 3.521,0.813 0.156,0.198 10 false 2 3.385,1.073 3.542,1.271 0.156,0.198 10 false 4 3.344,1.531 3.802,1.729 0.458,0.198 10 false C21 3.375,1.719 4.719,2.167 1.344,0.448 10 false Air Fuel Ratio Sensor (Bank 1 Sensor 1) 3.344,3.698 3.802,3.896 0.458,0.198 10 false C19 3.406,3.865 4.75,4.208 1.344,0.344 10 false Air Fuel Ratio Sensor (Bank 2 Sensor 1) 2.156,0.615 2.313,0.813 0.156,0.198 10 false 3 2.156,1.021 2.313,1.219 0.156,0.198 10 false 1 1.563,0.573 1.719,0.771 0.156,0.198 10 false 5 1.552,1.021 1.708,1.219 0.156,0.198 10 false 2 1.844,1.396 2.302,1.594 0.458,0.198 10 false A/F 0.917,0.885 1.375,1.083 0.458,0.198 10 false A/F 2.156,4.667 2.313,4.865 0.156,0.198 10 false 3 1.594,4.667 1.75,4.865 0.156,0.198 10 false 5 2.146,5.073 2.302,5.271 0.156,0.198 10 false 1 1.563,5.115 1.719,5.313 0.156,0.198 10 false 2 1.656,5.469 2.885,5.667 1.229,0.198 10 false EFI MAIN 0.542,6 1.615,6.198 1.073,0.198 10 false Battery 0.417,5.292 1.49,5.49 1.073,0.198 10 false FL MAIN 0.708,4.635 1.167,4.833 0.458,0.198 10 false EFI 3.354,5.604 5.042,5.802 1.688,0.198 10 false *1: for LHD 3.365,5.927 5.052,6.125 1.688,0.198 10 false *2: for RHD 3.365,6.26 5.198,6.458 1.833,0.198 10 false *3: Shielded

CAUTION / NOTICE / HINT

HINT:
·

A low Air Fuel ratio (A/F) sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.


·

A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.


·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.


·

Bank 2 refers to the bank that does not include the No. 1 cylinder.


·

Sensor 1 refers to the sensor closest to the engine assembly.


·

Sensor 2 refers to the sensor farthest away from the engine assembly.


·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, andother data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor (bank 1 sensor 1) connector.


b.

Disconnect the air fuel ratio sensor (bank 2 sensor 1) connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C21-1 (HA1A) - C39-86 (HA1A) Always Below 1 Ω
C21-3 (A1A+) - C39-93 (A1A+) Always Below 1 Ω
C21-4 (A1A-) - C39-116 (A1A-) Always Below 1 Ω
C19-1 (HA2A) - C39-109 (HA2A) Always Below 1 Ω
C19-3 (A2A+) - C39-120 (A2A+) Always Below 1 Ω
C19-4 (A2A-) - C39-119 (A2A-) Always Below 1 Ω
C21-1 (HA1A) or C39-86 (HA1A) - Body ground Always 10 kΩ or higher
C21-3 (A1A+) or C39-93 (A1A+) - Body ground Always 10 kΩ or higher
C21-4 (A1A-) or C39-116 (A1A-) - Body ground Always 10 kΩ or higher
C19-1 (HA2A) or C39-109 (HA2A) - Body ground Always 10 kΩ or higher
C19-3 (A2A+) or C39-120 (A2A+) - Body ground Always 10 kΩ or higher
C19-4 (A2A-) or C39-119 (A2A-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REPLACE AIR FUEL RATIO SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE AIR FUEL RATIO SENSOR

Result:
Proceed to
NEXT



NEXT

3.CHECK WHETHER DTC OUTPUT RECURS
3.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Drive the vehicle in accordance with the driving pattern described in the Confirmation DrivingPattern.


g.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

h.

Read the pending DTCs.

Result:
Result Proceed to
NORMAL (DTCs are not output) A
ABNORMAL (DTC P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256 is output) B




A

END

B