Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P060A  Internal Control Module Monitoring Processor Performance  


DESCRIPTION

The main CPU and sub CPU of the ECM perform data communication between each other. The main CPU monitors the communication and WDC pulses from the sub CPU. When the signal malfunctions below are detected, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P060A Internal Control Module Monitoring Processor Performance A CPU reset is performed after one of the following conditions is met (1 trip detection logic):
·

There is an ECM main CPU error.

·

There is an ECM sub CPU error.

·

There is an electronic throttle monitoring CPU error.


ECM Comes on DTC stored

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the GTS off.

5.

Turn the ignition switch off.

6.

Disconnect the GTS.

7.

Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

8.

Connect the cable to the negative (-) battery terminal.

9.

Connect the GTS to the DLC3.

10.

Turn the ignition switch to ON and turn the GTS on.

11.

Wait 16 seconds or more.

12.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

15.

Input the DTC: P060A.

16.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ OUTPUT DTC (DTC P060A)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.


g.

Connect the cable to the negative (-) battery terminal.


h.

Turn the ignition switch to ON.


i.

Turn the GTS on.


j.

Wait for 16 seconds or more.


k.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

l.

Read the DTCs.

Result:
Result Proceed to
DTC is not output A
DTC P060A is output B




A

B