Home › Engine / Hybrid System › 1HZ (ENGINE CONTROL) › ECD SYSTEM
RM25T0E _51 Engine / Hybrid System _029759 1HZ ENGINE CONTROL _0135351 ECD SYSTEM C

1HZ ENGINE CONTROL  ECD SYSTEM  42  Vehicle Speed Sensor Signal Circuit Malfunction  


DESCRIPTION

The vehicle speed sensor outputs a 4-pulse signal for every revolution of the rotor shaft, which is rotated by the transmitted output shaft via the driven gear. After this signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter, it is then transmitted to the emission control ECU. The emission control ECU determines the vehicle speed based on the frequency of these pulse signals.

A190471E03
3.719,1.833 5.135,2 1.417,0.167 10 false Combination Meter 2.927,0.531 3.906,0.698 0.979,0.167 10 false 4-Pulse Signal 4.813,0.531 5.771,0.698 0.958,0.167 10 false 4-Pulse Signal 5.521,1.844 7.146,2.094 1.625,0.25 10 false Emission Control ECU 1.271,1.802 2.76,2.052 1.49,0.25 10 false Vehicle Speed Sensor

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
42 Vehicle Speed Sensor Signal Circuit Malfunction All conditions below are detected continuously for 8 seconds or more:
·

Vehicle speed signal: 0 km/h (0 mph)

·

Engine speed: 2000 to 3200 rpm

·

Engine coolant temperature: 80°C (176°F) or more

·

Load driving


·

Open or short in vehicle speed sensor circuit

·

Vehicle speed sensor

·

Combination meter

·

Emission control ECU


- DTC stored

WIRING DIAGRAM

A190473E04
1.083,1.917 1.375,2.063 0.292,0.146 10 false L25 1.083,2.083 2.354,2.271 1.271,0.188 10 false Combination Meter 2.625,1.229 2.823,1.406 0.198,0.177 10 false 8 4.646,0.927 4.844,1.104 0.198,0.177 10 false 5 4.552,1.135 4.865,1.313 0.313,0.177 10 false A31 4.604,1.771 4.802,1.948 0.198,0.177 10 false 14 4.552,1.979 4.833,2.156 0.281,0.177 10 false A30 4.906,1.958 5.188,2.135 0.281,0.177 10 false E1 4.938,1.083 5.281,1.26 0.344,0.177 10 false SP1 4.865,2.698 6.615,2.896 1.75,0.198 10 false Emission Control ECU

PROCEDURE

1.CHECK OPERATION OF COMBINATION METER ASSEMBLY
a.

Drive the vehicle and check if the operation of the speedometer in the combination meter is normal.

OK:

Speedometer operation is normal.


HINT:
·

The vehicle speed sensor is operating normally if the speedometer reading is normal.

·

If the speedometer does not operate, check it by following the procedure described in Speedometer Malfunction.




Result:
Proceed to
OK
NG



OK

2.CHECK EMISSION CONTROL ECU

NG

2.CHECK EMISSION CONTROL ECU
a.

Shift the shift lever to the neutral position.


b.

Jack up the vehicle.


c.

Rotate a driving wheel slowly.


d.
A311443C02
1.948,0.323 2.365,0.615 0.417,0.292 1.25,0.323 1.667,0.615 0.417,0.292 1.677,1.708 1.844,1.031 true 2.406,1.646 2.115,0.948 true 0.104,0.24 0.417,0.438 0.313,0.198 10 false *a 1.917,4.115 2.229,4.313 0.313,0.198 10 false *b 0.229,3 2.063,3.198 1.833,0.198 10 false 4.5 to 5.5 V 0.875,3.833 1.031,4.031 0.156,0.198 10 false 0 1.531,1.75 2.188,2.167 0.656,0.417 10 false 14 (E1) 2.323,1.656 2.979,2.073 0.656,0.417 10 false 5 (SP1) 1.344,0.385 1.708,0.635 0.365,0.25 10 false A30 2.031,0.385 2.396,0.635 0.365,0.25 10 false A31
*a Component with harness connected
(to Emission Control ECU)
*b Driving Wheel Rotated


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A31-5 (SP1) - A30-14 (E1) Ignition switch ON Voltage generated intermittently


HINT:

The output voltage should fluctuate up and down similarly to the diagram when the wheel is turned slowly.



Result:
Proceed to
OK
NG



OK

NG