Home › Engine / Hybrid System › 1GR-FE (INTAKE / EXHAUST) › EXHAUST PIPE(for Model Code #J71, #J76 Series)
RM25T0E _51 Engine / Hybrid System _029771 1GR-FE INTAKE / EXHAUST _0135416 EXHAUST PIPE(for Model Code #J71, #J76 Series) A

1GR-FE INTAKE / EXHAUST  EXHAUST PIPE(for Model Code #J71, #J76 Series)  INSTALLATION  


PROCEDURE

Hide 17410 1.INSTALL FRONT EXHAUST PIPE ASSEMBLY

HINT:

Be sure to install the gasket so that it is flush with the installation surface and not at an angle.


a.

Inspect the compression spring.

i.
A104634

Using a vernier caliper, measure the free length of the compression spring.

Minimum free length:

38.9 mm (1.53 in.)


If the free length is less than the minimum, replace the compression spring.



b.
A104635C25
2.531,0.938 3.01,0.938 true 1.521,1.708 2.125,1.51 true 3.052,0.854 3.313,1.042 0.26,0.188 10 false *a 1.313,1.625 1.521,1.792 0.208,0.167 10 false *1
*1 Gasket
*a Wooden Block


Using a plastic-faced hammer and wooden block, tap a new gasket onto the exhaust manifold sub-assembly RH so that the gasket is flush with the exhaust manifold sub-assembly RH ends.

NOTICE:
·

Install the gasket in the correct direction.

·

Do not damage the outer surface of the gasket.

·

Do not reuse the gasket.

·

Do not push in the gasket with the front exhaust pipe assembly when connecting it.




c.

Install the exhaust pipe damper to the front exhaust pipe assembly with 2 new nuts and 2 new bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


d.

Install the exhaust pipe support cushion to the front exhaust pipe assembly with the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

HINT:
A218311C01
2.375,1.552 2.604,1.76 0.229,0.208 10 false *a
*a 40 mm (1.57 in.)


Be sure to install the exhaust pipe support cushion with a height of 40 mm (1.57 in.).



e.

Install the front exhaust pipe assembly to the exhaust manifold sub-assembly RH with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


f.

Connect the exhaust pipe support cushion with the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 17450 2.INSTALL NO. 2 FRONT EXHAUST PIPE ASSEMBLY

HINT:

Be sure to install the gasket so that it is flush with the installation surface and not at an angle.


a.

Inspect the compression spring.

i.
A104634

Using a vernier caliper, measure the free length of the compression spring.

Minimum free length:

38.9 mm (1.53 in.)


If the free length is less than the minimum, replace the compression spring.



b.
A104635C25
2.531,0.938 3.01,0.938 true 1.521,1.708 2.125,1.51 true 3.052,0.854 3.313,1.042 0.26,0.188 10 false *a 1.313,1.625 1.521,1.792 0.208,0.167 10 false *1
*1 Gasket
*a Wooden Block


Using a plastic-faced hammer and wooden block, tap new gasket onto the exhaust manifold sub-assembly LH so that the gasket is flush with the exhaust manifold sub-assembly LH ends.

NOTICE:
·

Install the gasket in the correct direction.

·

Do not damage the outer surface of the gasket.

·

Do not reuse the gasket.

·

Do not push in the gasket with the No. 2 front exhaust pipe assembly when connecting it.




c.

Install the exhaust pipe support cushion to the No. 2 front exhaust pipe assembly with the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

HINT:
A218311C01
2.375,1.552 2.604,1.76 0.229,0.208 10 false *a
*a 40 mm (1.57 in.)


Be sure to install an exhaust pipe support cushion with a height of 40 mm (1.57 in.).



d.

Install the No. 2 front exhaust pipe assembly to the exhaust manifold sub-assembly LH with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


e.

Connect the exhaust pipe support cushion with the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 17403 3.INSTALL CENTER EXHAUST PIPE ASSEMBLY

HINT:

Be sure to install the gasket so that it is flush with the installation surface and not at an angle.


a.

Inspect the compression spring.

i.
A104634

Using a vernier caliper, measure the free length of the compression spring.

Minimum free length:

38.9 mm (1.53 in.)


If the free length is less than the minimum, replace the compression spring.



b.
A104635C25
2.531,0.938 3.01,0.938 true 1.521,1.708 2.125,1.51 true 3.052,0.854 3.313,1.042 0.26,0.188 10 false *a 1.313,1.625 1.521,1.792 0.208,0.167 10 false *1
*1 Gasket
*a Wooden Block


Using a plastic-faced hammer and wooden block, tap 2 new gaskets onto the front exhaust pipe assembly and No. 2 front exhaust pipe assembly so that the gaskets are flush with the pipe ends.

NOTICE:
·

Install the gasket in the correct direction.

·

Do not damage the outer surface of the gasket.

·

Do not reuse the gasket.

·

Do not push in the gasket with the center exhaust pipe assembly when connecting it.




c.

Install the exhaust pipe support cushion to the center exhaust pipe assembly with the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

HINT:
A273234C01
0.792,1.01 0.906,1.01 0.906,1.01 1.385,1.417 false 0.573,0.917 0.771,1.125 0.198,0.208 10 false *a 2.531,1.563 2.823,1.719 0.292,0.156 10 false *b
*a Heat Resistant Plate
*b 35 mm (1.38 in.)


Be sure to install an exhaust pipe support cushion with a height of 35 mm (1.38 in.) and heat resistant plate.



d.

Install the center exhaust pipe assembly with the 4 compression springs and 4 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


e.

Connect the exhaust pipe support cushion with the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 17430 4.INSTALL TAILPIPE ASSEMBLY

a.

Install the No. 2 exhaust pipe support stay and exhaust pipe clamp to the tailpipe assembly with the 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install the exhaust pipe support cushion to the No. 2 exhaust pipe support stay with the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

HINT:
A273235C01
2.542,1.594 2.792,1.771 0.25,0.177 10 false *a
*a 30 mm (1.18 in.)


Be sure to install an exhaust pipe support cushion with a height of 30 mm (1.18 in.).



c.

Install the exhaust pipe support cushion to the tailpipe assembly with the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

HINT:
A273235C01
2.542,1.594 2.792,1.771 0.25,0.177 10 false *a
*a 30 mm (1.18 in.)


Be sure to install an exhaust pipe support cushion with a height of 30 mm (1.18 in.).



d.
A162141C01
2.417,0.333 2.25,0.333 2.25,0.333 1.938,0.667 false 2.458,0.229 2.771,0.427 0.313,0.198 10 false *a
*a New Gasket


Install a new gasket to the center exhaust pipe assembly.


e.

Install the tailpipe assembly with 2 new bolts and 2 new nuts.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)


f.

Connect the 2 exhaust pipe support cushions with the 4 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)